ZKTeco SBTL9000 Series User manual

Installation Guide
SBTL9000 Series
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.

It is recommended that the swing barrier must be installed on a horizontal solid platform with a
height of 50mm to 100mm.
1.
2.
3.
After installation, check if the connection is done correctly at the connecting points of the ground
wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part
of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in
time to avoid any failures caused by long-time operations.
4.
1
1 Installation Requirements
The installation position of the swing barrier turnstile depends on its size. A distance of 100mm between
the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the
machine to perform maintenance and adjustment. The reference €gure is shown below:
2 Installation Position
Figure 2-1 SBTL9000 Series Dual-lane
Make sure the ground wire of the system is reliably connected to avoid personal injuries or other
accidents.
It is also recommended that the swing barrier turnstile should not be used in the corrosive
environment.

3 Preparation
Below is the outline and dimensions of SBTL9000:
2
Figure 3-1
Tools: A measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included in
the package).
1.
2.
3.
The power and signal wires should be set separately to easily distinguish strong and weak power.
Please invite professional personnel to complete the wiring. The device must be connected to the
ground.
4.
Thread the connection wire of the device through the tube before assembly.
Material: A PVC anti-€re and insulation tube (diameter∫ 25mm), standard three-core power
extension wire, tether cable (random con€guration), M12 expansion screws (included in the
package).
1080
271
1184
780

4 Installation
Prepare the tools for product installation and sort out the auxiliaries according to the packing list.
Mark the screw hole at the centre of the stand, and the edge of the chassis base on the ground
according to the sizes as shown on the Figure 4-1.
1.
2.
3
Drill the holes with Ј14 and embed M12 anchor screws or expansion screws. As shown on the
Figure 4-2.
3.
Figure 4-2
Figure 4-1
1. Drill hole 2. Implantation of
the screw
3. Fix screw
SBTL9000
110
110
896
65 65
897
1152 1107

4
4. Place the swing barrier turnstile according to the sizes and positions as shown in the €gure before
installation and €xing.
For the outlets of the concealed cables, please refer the below diagram indicating the mounting
holes. The input voltage for this swing barrier turnstile is AC100V-120V/200V-240V and its master
and slave are connected by an 8-core cable (signal) and a 2-core cable (power). When installing the
swing barrier turnstile, the user only needs to connect it to the corresponding ports. Note that the
PVC conduits are laid 100mm under the ground, with the height of the exposed part not exceeding
100mm. In addition, the conduit outlet is bent back to prevent the ingress of water into the conduit.
5.
SBTL9000 series installation holes and cabling positions is shown in Figure 4-3:
A
Air Switch
Power 24V and network
communication line
Figure 4-3
100 142
1184
780
900
1080
100
273
990
M12Concrete
Anchor
Tether Cable
Power Line
Network Cable
φ25mm PVC pipe

5
Connect the online cables and perform the power-on test. Wait for 10 seconds for the turnstile to
complete the self-test program. At the same time, check if the indicators work properly. If
everything works €ne, you can tighten the screws and €x the device. If an exception occurs, please
contact your vendor.
6.
It is recommended that a warning line be marked on the ground after installing the device, so as
to prompt the pedestrian to stand behind the warning line when swiping the card. As shown in
Figure 4-4:
7.
WarningLine
WarningLine
Figure 4-4

5 Wiring Diagram
Below is the wiring diagram:
6

24V Power
Slave motor driving controller
Electromagnetic clutch
switch
Master machine board
switch
Master motor driving controller
Indicator light
RJ45
RJ45
GNDR1 G1 R2 G2
GND 12V GND BEEP
GLED
WD1
WD0
GND
12V GND
GND 485A
485B PE 485+
485- GND12V 12V GND WD0 WD1
GLED
BEEP
IN1 IN2 GND
B
G
R
12V G4R4
G3
R3
12V
K2
GND
K1
24V PE
GND12V
GND
SPK-
SPK+
InBio-PGates
B1 A1
B2 A2
B A
B/L A/H
RJ45
RJ45
GND
24V
GND
24V
K1
J9
J15
GND
24V
GND
24V
PHSD 2*4
GND
24V
GND
24V
PHSD 2*5
1 3 5
642
RS485
CANH
CANL
CAND
VCC
GND
RBR+
NC
RBR-
W
V
U
PE
BR-
BR+
24VB
GNDB
DO1
DO2
DO3
DO4
COMO
DI5
DI4
DI3
DI2
DI1
COM
SW1 SW2 SW3 SW4
1 3 5
642
GND
24V
GND
24V
PHSD 2*5
1 3 5
642
RS485
CANH
CANL
CAND
VCC
GND
RBR+
NC
RBR-
W
V
U
PE
BR-
BR+
24VB
GNDB
DO1
DO2
DO3
DO4
COMO
DI5
DI4
DI3
DI2
DI1
COM
SW1 SW2 SW3 SW4
1 3 5
642
J10
J11
J9
J6
H2
LED
LED
LED
WD0WD1
GLEDBEEP 12VGND 12VGND485+485- GND
GND 24V
GND
K1
K1CL 485- 485+ BEEP GLED
WD1 12V
WD0
TFT
19
LCD
5V
IR2
IR1 IR3 IR4 IR5 IR6
IR7 IR8 IR9 IR10 IR11 IR12
IR2
IR1 IR3 IR4 IR5 IR6
IR7 IR8 IR9 IR10 IR11 IR12
J10
J11
J9
J6
H2
LED
LED
LED
WD0WD1
GLEDBEEP 12VGND 12VGND485+485- GND
GND 24V
GND
K1
K1CL 485- 485+ BEEP GLED
WD1 12V
WD0
´þ•·Éä 1
´þ•·Éä 2
‰ÓÉ䶸 1 ‰ÓÉ䶸 2 ‰ÓÉ䶸 3 ‰ÓÉ䶸 4
‰ÓÉ䶸 5 ‰ÓÉ䶸 6 ‰ÓÉ䶸 7 ‰ÓÉ䶸 8
SBTH5000_IR1
SBTH5000_IR2
SBTH5000_IR4
SBTH5000_IR1
SBTH5000_IR2
SBTH5000_IR4
SBTH5000_TCB
SBTH5000_TCB
B1 A1 Reader485
B2 A2 MCU IR485
B/L A/H
Master/Slave motor driving controller
B A Motor driving controller
B1 A1 Reader485
B2 A2 MCU IR485
B/L A/H
Master/Slave motor driving controller
B A Motor driving controller
Indicator light
Indicator light
Indicator light
switch
Indicator light
Indicator light
Indicator light
Indicator light
Electromagnetic clutch
1 3 5
642
IR13 IR14
SBTH5000_IR3
TFT
19
LCD
IR13IR14
SBTH5000_IR3
1 3 5
642
Indicator light

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com