ZKTeco SBT2000S User manual

Installation Guide
SBT2000S Swing Barrier Turnstile
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.

It is recommended that the swing barrier turnstile be installed on a horizontal solid platform with
50 mm to 100 mm in height, the horizontal angle must not be greater than ±0.7°.
1.
2.
3.
After installation, check if the connection is done correctly at the connecting points of the ground
wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part
of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in
time to avoid any failures caused by long-time operations.
4.
1
1 Installation Requirements
The installation position of the swing barrier turnstile depends on its size. A distance of 100mm between
the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the
machine to perform maintenance and adjustment. The reference figure is shown below:
2 Installation Position
Figure 2-1 SBT2000S Series Dual-lane
Make sure the ground wire of the system is reliably connected to avoid personal injuries or other
accidents.
It is also recommended that the swing barrier turnstile should not be used in the corrosive
environment.
2274.02
2174.02
900
592
800

3 Preparation
Below is the outline and dimensions of SBT2000S:
2
Figure 3-1
Tools: A measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included in
the package).
1.
2.
3.
The power and signal wires should be set separately to easily distinguish strong and weak power.
Please invite professional personnel to complete the wiring. The device must be connected to the
ground.
4.
Thread the connection wire of the device through the tube before assembly.
Material: A PVC anti-fire and insulation tube (diameter≥25mm), standard three-core power
extension wire, tether cable (random configuration), M12 expansion screws (included in the
package).
202
187
531 814
1109
592
800

4 Installation
Prepare the tools for product installation and sort out the auxiliaries according to the packing list.
Mark the screw hole at the centre of the stand, and the edge of the chassis base on the ground
according to the sizes as shown on the Figure 4-1.
1.
2.
3
Drill the holes with Ф14 and embed M12 anchor screws or expansion screws. As shown on the
Figure 4-2.
3.
Figure 4-2
Figure 4-1
1. Drill hole 2. Implantation of
the screw
3. Fix screw
SBT2000S
148
51

M12Concrete
Anchor
Power Line φ25mm PVC pipe
1019.15
1225.00
120.50
2274.02
2174.02
900
800
592
4
4. Place the swing barrier turnstile according to the sizes and positions as shown in the figure before
installation and fixing.
For the outlets of the concealed cables, please refer the below diagram indicating the mounting
holes. The input voltage for this swing barrier turnstile is AC100V-120V/200V-240V and its master
and slave are connected by an 2-core cable (signal) and a 2-core cable (power). When installing the
swing barrier turnstile, the user only needs to connect it to the corresponding ports. Note that the
PVC conduits are laid 100mm under the ground, with the height of the exposed part not exceeding
100mm. In addition, the conduit outlet is bent back to prevent the ingress of water into the conduit.
5.
SBT2000S series installation holes and cabling positions is shown in Figure 4-3:
Air Switch
Figure 4-3

WarningLine
WarningLine
Figure 4-4
5
6. Connect the online cables and perform the power-on test. Wait for 10 seconds for the turnstile to
complete the self-test program. At the same time, check if the indicators work properly. If
everything works fine, you can tighten the screws and fix the device. If an exception occurs, please
contact your vendor.
7. It is recommended that a warning line be marked on the ground after installing the device, so as to
prompt the pedestrian to stand behind the warning line when swiping the card. As shown in Figure
4-4:

5 Wiring Diagram
Below is the wiring diagram:
6