ZKTeco SBT1000S User manual

1
Swing Barrier Turnstile Installation Guide
Applicable Models: SBT1000S
Version: 1.2Date: May. 2018

1
Chapter 1 Overview
1.1 Preparation
1) Cut a slot from the floor with a proper tool. The depth and width should be approximately
100mm and 30mm.
2) Put the wire through the pipe.
3) In order to avoid the impact on communication, 220V/110V power line (high voltage) and signal
line (low voltage) should be separated. The ground wire must be connected.
SBT1000S series appearances and sizes as shown in Figure 1-1
Figure 1-1
Chapter 2 Installation
2.1 Before the installation, it is necessary to check the device first:
1) Connect the wires to power supply.
2) Open the air switch to test whether the device is working properly, wait for 10 seconds for the
gate to complete self-test program. If everything is normal, you can start the installation
procedures. If an exception occurs, please contact your vendor for information.
2.2 Cables installation
For the outlets of the concealed cables, please refer to the drawing showing the mounting holes.
The input voltage for this swing barrier turnstile is AC100-120V/200-240V. Note that the PVC conduits
are buried 100mm below the ground, with the height of the exposed part more than 100mm.As
shown in Figure 2-2.

2
Figure 2-2
2.3 Chassis installation
1) Verify the accessories on the list and gather tools.
2) Posit the machine on the right place.
3) Drill on the ground according to the positioning tape.
4) Embedding four expansion bolts (M12) into the positioning holes.
5) Remove the access cover, as shown in Figure 2-4A.
6) Put pads and use a wrench to tighten nuts, as shown in Figure 2-4B.
7) Close the access cover, as shown in Figure2-4C.
8) Install the barrier arm (glass baffle or U-shaped stainless steel pipes), as shown in Figure2-4D.
1
Figure 2-3A
2
Figure 2-3B
Screw pad
Chassis
Ground
Expansion bolt
4-M12
Ground
Base concrete

3
Chapter 3 Wiring diagram and menu instruction
3.1 Wiring diagram
Check circuit according to the following wiring diagram:
Figure 3-1
C
o
nt
r
o
l
l
e
r
UP DOWN ENT ESC
Reader
R
e
ad
e
r
1
Reader 2
485 Reader
GND
1
2
V
Lock1
Lock2
1
2
V
PO
W
E
R
M
+
M
-
RX
G
ND
T
X
485A EGND 458B
C
AN
L
E
GN
D
CA
NH
IR7
IR8
IR6
IR5
IR3
IR4
IR2
IR1
NC
C
OM
NO
G
ND
1
2VN
C
CO
M
N
O
GN
D
12
V5V
G
ND
A
B
Z
1
2V
LE
DG
L
ED
R
L
ED
Y
GN
D
ZUO YOU GND 12V
EC
_L
1
G
ND
E
C_
H1
IN SW IN SW IN SW
E
C-
L
EC
-H
24VOUT GND BA
T
GN
D
2
4V
IN
E
GN
D
G
ND
V
CC
GN
D
VC
C
GN
D
V
CC
GN
D
V
CC
GN
D
VC
C
GN
D
VC
C
GN
D
V
CC
G
ND
V
CC
G
ND
Encoder
E
lectromagne
ticclutch
VC
C
G
NDVC
C
G
ND
VCC GND VCC GND
V
CC
GN
DV
CC
G
N
DVC
C
G
ND
VCC GND
AP-R：IR3
IR3 on the top
SPK
C
OM
N
O
CO
M
NO
12
V
OU
T
GN
D
24V
Po
we
r
Firefighting port
SBT1000S series
Wiring diagram
C
o
n
t
r
o
l
b
o
a
rd
Firefightingboa
rd
LED light
KR800
Infrared sensor
Motor
3
Figure 2-3C
4
Figure 2-3D

4
3.2 Menu instruction
There are 4 keys on the control panel, including "UP", "DOWN", "ENT" and "ESC".
Press the ENT button, enter the password input interface, the default password is: UP, UP, DOWN,
DOWN, DOWN, DOWN. If any step fails please press the ESC button to get back.
3.3 Modify the menu
After enter the menu operation system, press “UP” or “DOWN” to select an item and then press “ENT”
to enter the menu, press “UP” or “DOWN” to modify the menu. Finally press “ENT” to confirm.
Chapter 4 Troubleshooting
Number Failure description Analysis and solution
1Gate open, but it is not in place
Motor resistance may be too large,
Increase the value of minimum
compensation speed.
2No sound 1. Check if the speaker wire is loose.
2. Check if voice is turned off.
3Swing arm is not centered Enter the menu of "Swing arm zero
correction" to adjust the zero position.
4The control panel LCD shows
"Encoder wiring error"
Please check if the wiring of encoder A, B
phase is reversed, If yes, replace it.
5The direction of gate open is
inconsistent with swiping card.
Access controller left and right gate
signal line is reversed, right and left can
be adjusted
6Swipe card, but gate does not
open.
1. Check if the menu setting interface
does not exit.
2. Check if the gate signal of the access
controller is connected to the gate
controller.
3. Enter menu to see if current mode is
set to card unavailable.