Zte MF920US User manual

MF920U
Quick Start Guide

1
Getting to Know Your Device
Appearance
The following gure is for your reference only.
1. Charging/micro-USB jack
2. Indicator light
3. Power key
• Press and hold for about 2 seconds to power on/
o󰀨 your device.
• Press and hold for about 10 seconds to power o󰀨
your device, if it is in abnormal status. And then
press and hold for about 2 seconds to power on
your device again.

2
4. WPS key
Press and hold for about 2 seconds to activate the WPS
function.
5. micro-SIM card slot and reset hole
Reset hole: Press and hold for about 2 seconds to restore
your device to the factory settings.
Getting to Know Your Device
Indicator lights
Indicator Status Description
Battery
Red solid /
blinking
The battery is low. Please
charge the battery.
Green
blinking
The battery is being charged.
Green
solid
The battery level is middle or
high.
Light o󰀨 Your device is powered o󰀨 and
not being charged.
Wi-Fi
Blue solid Wi-Fi is active.
Blue
blinking
WPS is active.
Light o󰀨 Wi-Fi is o󰀨.

3
SMS
Blue solid You have unread messages.
Blue
blinking
You have new messages or the
message storage is full.
Light o󰀨 There is neither an unread
message nor a new message.
Network
Red The device is in error status.
• The device is not
registered to the mobile
network.
• There is no micro-SIM card
inserted.
• There is no network
service available.
Green
solid
The device is registered to the
2G/3G mobile network.
Green
blinking
The device is connected to the
2G/3G mobile network and data
is being transferred.
Blue solid The device is registered to the
4G LTE network.
Blue
blinking
The device is connected to the
4G LTE network and data is
being transferred.

4
Getting to Know Your Device
Connection Scenarios
The device uses your micro-SIM card to access the
Internet. It allows multiple clients to surf on the Internet at
the same time. The following gure is for your reference
only.

5
Installing the micro-SIM Card
1. Open the micro-SIM card slot cover.
NOTE:
Do not remove the cover rudely, because it is connected
with the device.
2. Install a micro-SIM card to the micro-SIM card slot.
WARNING!
Your device does not support SIM cards, nano-SIM cards or
any other non-standard micro-SIM cards. To avoid damage
to the device, do not use those cards or any card holders.
3. Close the micro-SIM card slot cover.

6
Connecting to Your Device
Using Wi-Fi
1. Power on your device.
2. Ensure that your computer or other client devices
have enabled Wi-Fi, and search for available wireless
networks.
NOTE:
Refer to your Wi-Fi-enabled client device manual for further
details on how to search for wireless networks. If you use
a computer, you need to set your computer to obtain an IP
address automatically.
3. Select the Wi-Fi name (SSID) of your device, and click
Connect.
4. Enter the Wi-Fi password if necessary, and click OK.
NOTE:
Refer to the chapter Getting to Know the Wi-Fi SSID and
Password to get the default Wi-Fi SSID and password.
5. Wait until the client device is connected to your device
successfully.

7
Using a USB Cable
1. Connect a computer to your device with a USB cable.
2. Power on your device. The operating system detects
and identies new hardware, and automatically installs
the software.
NOTE:
If the system does not automatically launch installation,
you can double-click the device installation icon in My
Computer > ZTEMODEM to install the software.
3. Wait until the computer is connected to your device
successfully.
Getting to Know the Wi-Fi SSID and
Password
You can view the label on the device to get the default Wi-Fi
SSID and password.

8
Logging in to the 4G Mobile Hotspot
Conguration Page
1. Ensure that the connection between your device and the
client device is correct.
2. Launch the Internet browser and enter http://192.168.0.1
or http://u.ztedevice.com in the address bar.
3. Enter the password to log in to the 4G Mobile Hotspot
conguration page.
NOTE:
You can view the label on the device to get the default
password.
Changing the Wi-Fi SSID or Password
1. Log in to the 4G Mobile Hotspot conguration page.
2. Select Wi-Fi Settings.
3. Change the Network Name (SSID) or the Password in
the Main SSID area.
4. Click Apply.