ZURN AquaSense Z6922-XL Series User manual

®
LIMITED WARRANTY
All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from
the date of purchase. Decorative nishes warranted for one year. We will replace at no costs goods that prove defective provided
we are notied in writing of such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been
properly maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or
damages whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replace-
ment of the defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended
use and the purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of
merchantability is expressly excluded. If the products sold hereunder are “consumer products,” the implied warranty of merchantabi-
lity is limited to a period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our
catalogs and lists are approximate and are not guaranteed.
Sensor-Operated Battery-Powered
Lavatory Faucets
Z6922-XL
Z6922-XL
AquaSense®
Z6922-XL Series
Sensor-Operated Lavatory Faucets for
Battery or Plug-In Installations.
Installation,
Operation, Maintenance
and Parts Manual
Patented and Patents Pending
WARNING: Cancer and Reproducve Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproducvo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et eets néfastes sur la reproducon - www.P65Warnings.ca.gov

FV351 Rev. F 7/11/2018
Page 2
IMPORTANT:
• ALL PLUMBING IS TO BE INSTALLED IN ACCORDANCE
WITH APPLICABLE CODES AND REGULATIONS.
• FLUSH ALL WATER LINES PRIOR TO INSTALLATION.
• SENSOR UNITS SHOULD NOT BE LOCATED ACROSS
FROM EACH OTHER OR IN CLOSE PROXIMITY TO HIGH-
LY REFLECTIVE SURFACES.
1.- Spout Installation
If there is an exsisting faucet, turn off water supply and remove
the old faucet. Assure supply lines are completely ushed and
free of debris. Clean lavatory surface around
the mounting area for the new sensor faucet.
Place the sensor connector wire and shank through the rubber
o-ring and hole in the lavatory. Place moon shaped washer
over shank from the back of the lavatory and secure the entire
assembly to the lavatory with the mounting nut. *Be careful
not to pinch Sensor wires.
Once the spout is in place and tightened, attach the 90º elbow
and nipple provided. Teon tape is preferred at this connection
to ensure a watertight connection. Be sure to tighten so that
the nipple is straight down.
2.- Electronics Module Installation
Attach electronics module to the shank using the hex nut and
gasket provided. Orient the electronics in a convenient location
and tighten hex nut. DO NOT USE THREAD SEALANT.
Attach sensor connector wire from the faucet to the mating sen-
sor connector wire from the eletronics module. Orient connectors
so that the pins are properly aligned before pressing connectors
together. Do not force together, damage to pins may occur.
Secure the cable connectors with the locking ring provided.
Be certain that the cable connection is made before the
batteries are installed.
3a.- Battery Installation
Loosen the battery cover screw with the supplied allen wrench.
Remove the cover and install the batteries as indicated on the
battery case. Replace the battery cover and secure.
3b.- ACA Plug-In Adapter Installation
When using the -ACA plug-in power supply remove sticker
at location (A) and plug in adapter.
4.- Filter or Mixing Tee or Mixing Valve
Installation
The supplied inlet lter, (item 4) must be used with every faucet
unless a mixing tee or mixing valve is ordered. The inlet lter is
attached directly to the electronics module’s water inlet. Tem-
pered water is then supplied to the lter using a standard 3/8”
x 1/2” ball riser (supplied by others.)
The optional mixing tee assembly (-MT) or mixing valve (-MV)
have integral lters and back checks. These take the place of
the standard inlet lter when ordered. The mixing tee or mixing
valve outlet attaches to the electronics module with a 3/8” x
1/2” ball riser (supplied by others). Hot and cold water is then
supplied to the appropriate 3/8” compression inlets.
1
2
3

FV351 Rev. F 7/11/2018
Page 3
Z6922 Repair Kits
Item Product No. Description
1P6922-XL-1 No Lead Spout Base with Sensor
Assembly
2
P6900-B-L Electronics Box with Solenoid
P6900-XL-B-L No Lead Electronics Box with Solenoid
P6900X-B-L Extended Range Electronics Box with
Solenoid
3P6900-SRK Solenoid Rebuild Kit (Diaphram,
plunger and plunger spring)
4P6900-120 Filter Kit
5P6900-MV-7 Filter Screen
6P6920-43 Mounng Kit
Item Product No. Description
7 P6900-ACA Oponal Plug-In Power Converter
8
P6900-GB 5 3/8” Gooseneck Spout with Nut
P6900XL-GB 5 3/8” No Lead Gooseneck Spout with
Nut
9P6900-20A-GN 1.5 GPM Vandal Resistant Aerator
10 P6900-SG Shank Gasket
11
P6900-MT Mixing Tee w/Filters and Back Checks
P6900-MT-XL No Lead Mixing Tee w/Filters and Back
Checks
12 P6900-MV-ZL Mixing Valve w/Filter

OPERATION
1.) Invisible light rays are continually emitted from the
faucet sensor.
2.) When the user’s hands come into range of the sen-
sor’s detection zone (8” approx.), the beam is reected
back to the sensor’s reciever and converted to a low
voltage electrical signal activating a solenoid valve.
3.) After the user removes their hands, the absense of re-
ected light stops the low voltage electrical signal, closing
the valve. The circuit automatically resets for the next user.
4.) If an object is in view continuously for thirty seconds,
the faucet will automatically shut off. The faucet will remain
off until the object is removed. After the object is removed,
the faucet functions normally.
CARE AND CLEANING INSTRUCTIONS
DO NOT use abrasive or chemical cleaners to clean faucets as they will dull the luster and attack the chrome or spe-
cial decorative nishes. Use only mild soap and water, then wipe dry with a clean cloth or towel. While cleaning the
bathroom tile and oor, the faucet and electronics should be protected from splattering of water, cleaner, acids and
cleaning uids that can damage the sensor faucet.
TROUBLESHOOTING GUIDE
SPECIFICATION
Voltage: 6 VDC
(4 “AA” Alkaline)
Sensor Range: 8” Approximate
Operating Water
Pressure: 20-80 psi
Ambient
Temperature: 32ºF to 122ºF (0ºC to 50ºC)
Operational Water
Temperature: 35°F to 140°F (2°C to 60°C)
Aerator: 1.5 GPM Vandal-Resistant
(Standard)
PROBLEM POSSIBLE CAUSE TO DIAGNOSE REMEDY
Faucet will not ow
water
Water supply not turned
on.
Check supply stops. Turn on water.
Batteries not connected. Check connections. Reconnect batteries.
Cable connection is not
fully engaged.
Check cable
connection.
Remove battery, and disengage
the cable connection. Check cable
connection for broken pins and
reconnect cable.Check battery for
voltage level and reinstall.
Low battery. Flashing red light in
sensor eye indicates
low battery.
Remove batteries and replace with
4 new alkaline batteries.
Solenoid valve
inoperative.
Move hand in front of
faucet to see if solenoid
valve is clicking.
If clicking, open solenoid valve and
clean it.
If not clicking, replace solenoid
valve.
Sensor/electronics are
inoperative
Move hand in front of
faucet to see if solenoid
valve is clicking. See
note in Step 4.
Remove the battery and short
circuit the battery terminals with
allen wrench. This will reset the
electronics. Replace battery.
Filter is plugged. Shut off water supply.
Remove clean out cap.
Clean the lter and reassemble.
Faucet continues to
run for more than
30 seconds or drips
Solenoid valve is dirty. Open the solenoid valve
and check for debris.
Carefully observe
the way valve goes
together for reassembly.
Shut off water supply. Disassemble
solenoid and remove debris from
diaphragm and/or plunger tip.
Reassemble solenoid.
AquaSense®is a registered trademark of Zurn Industries, LLC.
Printed in the U.S.A.
ZURN INDUSTRIES, LLC 5900 Elwin Buchanan Drive, Sanford, NC U.S.A. 27330, Ph. 1-800-997-3876, Fax [phone]
In Canada: ZURN INDUSTRIES LIMITED 7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, Ph. 905-405-8272, Fax [phone]
Rev. F Date: 7/11/2018 C.N. No. SAN008311 Prod. | Dwg. No. FV351