ZURN Sundara Reef Z5001.01 User manual

Sundara® Reef Single Basin
Hand Washing System
LIMITED WARRANTY
All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the
date of purchase. Decorative nishes warranted for one year. We will replace at no costs goods that prove defective provided we are
notied in writing of such defect and the goods are returned to us prepaid at Atlanta, GA, with evidence that they have been properly
maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages
whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replacement of the
defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended use and the
purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of merchantabi-
lity is expressly excluded. If the products sold hereunder are “consumer products,” the implied warranty of merchantability is limited to
a period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our catalogs and lists
are approximate and are not guaranteed.
NOTE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT.
NOTE: The information in this manual is subject to change at any time without notice. Installations may
be performed at different times of construction by different individuals. For this reason, these instructions
should be left on-site with the facility or maintenance manager.
Z5001.01
Sundara®Reef Single Basin
Hand Washing System
Installation,
Operation, Maintenance
and Parts Manual
Patented and Patents Pending
WARNING: Cancer and Reproducve Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproducvo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et eets néfastes sur la reproducon - www.P65Warnings.ca.gov
ZURN INDUSTRIES, LLC 5900 Elwin Buchanan Drive, Sanford, NC U.S.A. 27330, Ph. 1-800-997-3876, Fax [phone]
In Canada: ZURN INDUSTRIES LIMITED 7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, Ph. 905-405-8272, Fax [phone]
Rev. A Date: 8/6/2018 C.N. No. SAN008335 Prod. | Dwg. No. FV605

FV605 Rev. A 8/6/2018
Page 2
Be sure the sink/lavatory/basin is clear from any objects upon making the sensor to electronics connection initiating the self-
calibration feature. The sink must be clear of any and all objects in order to calibrate appropriately (calibration time approx 30-
60sec). Note: Not applicable to manual faucet installations.
S’assurer qu’aucun objet ne se trouve sur l’évier/le lavabo/le bac lors du branchement du capteur sur l’électronique, ce qui lance la
fonction d’auto-étalonnage. Rien ne doit se trouver sur le lavabo pour permettre son auto-étalonnage correct (temps
d’étalonnage de 30 à 60 s environ).
Overview:
Designed for modern commercial restrooms, the Sundara system delivers a superior user experience in both form and func-
tion. Crafted by world-class industrial designers Sundara combines seamless basin designs with curated faucets and soap
dispensers, delivering a complete, easy to install hand washing solution.
Specications:
Sundara®Reef single basin lavatory system manufactured by Zurn Industries. Lavatory shall be mounted at standard height
to conform with ANSI, UFAS, TAS and ADA Accessibility Standards. Counter and integral basin to be constructed of Sundara®
solid surface resin with aluminum trihydrate and other additives conforming to CSA B45.5 / IAPMO Z124 and IAPMO IGC 156
standards. Shroud enclosure is constructed of satin nished type 304, 18 gage stainless steel designed for easy access with
vandal resistant hardware. Lavatory is furnished complete with 0.5 gpm spray aerator faucet (specify model in sensor manual)
and optional liquid soap dispenser (specify model), ½” quarter turn supply stops, 3/8” exible supply risers, chrome 1 ¼” tail
piece, and chrome 1 ¼” p-trap for complete system operation.
Paired Faucet Typical Specication
(Refer to faucet manual for more details on specic model)
Voltage: 6 VDC Series [4 “AA” (Alkaline or Lithium) and/or external power option]
Sensor Range: Self-calibrated, dependent upon sink depth and nish.
Operating Water Pressure: 10-125 psi
Operational Water Temperature: 33°F to 140°F (1°C to 60°C)
Aerator: 0.5 GPM Vandal-Resistant (Standard)
Paired Soap Dispenser Typical Specication
(Refer to soap dispenser manual for more details on specic model)
Power Supply: AC 110 V; DC 6V
Soap Viscosity: 100-3800 cps
Operating Temperature: 340- 1310F
Typical Dispensed Volume: 1.25 ml
Prior to Installation:
• If applicable, carrier (Z1240 series) is installed behind the wall.
• Hot and cold water supply lines are installed as per building codes.
• Care shall be taken when installing this product to prevent damage of any exposed or decorative surfaces.
• Measure the drain outlet from the oor.
Important Safety Information:
• Installer is responsible for ensuring the product is installed and conforms to all plumbing codes and ordinances.
• Do not convert or modify this Zurn product yourself. All warranties will be voided.
• Water supply lines must be sized according to building design in order to provide adequate water supply for each xture.
• Flush all water lines prior to making connections.
• Minimum 2 people required for the sink installation
• Au minimum, 2 personnes sont requises pour l’installation du lavabo.

FV605 Rev. A 8/6/2018
Page 3
Z5001.01 Parts List
5
9
8
7
4
Item Name QTY
1 Basin 1
2 Shroud Wall Bracket 1
3 Shroud 1
4 Mounting (L) Bracket 2
5 "Wall Hanger Bracket
(Available only for Retrot)" 1
6 Grid drain 1
7 Water Supply Items 2
8Drain Adapter Assembly 1
9P Trap Assembly 1
10 Sensor Faucet 1
11 Soap Dispenser (If Ordered) 1
12 "5/16-18 Screw for Mounting
L Bracket to Basin" 4
13 #10-24 Screw for Drain Adapter
and Shroud 6
14 #6-32 Screw for Grid Drain 2
15 Coarse Screw for Wall Bracket 2
16 Flanged Socket Head Screw for
Shroud 2
17 Oversize 5/16 Washer 4
18 #10 Flat Washer for Drain Adapter
and Shroud 8
19 3/8-16 Hex Bolt with washer 14
20 3/8" Toggle Never Drop Anchor 14
21 3/8 Fender Washer 8
5
9
8
7
4
5
9
8
7
4
5
9
8
7
4
5
9
8
7
4
Optional
5
9
8
7
4
5
9
8
7
4
5
9
8
7
4

FV605 Rev. A 8/6/2018
Page 4
Plumbing and Electrical Rough-In
Note: InstallingtheP-trapoutletlowerthan19.5”fromnished
oorwillpreventthevandalshroudfrombeinginstalled.
6 [152]
15 [381]
30 [762]
34 [863]
291
2[752]
283
4[733]
143
4[378]
11
4[29]
31
4[84]
191
2[493]
29 [735]
23
4[71]
20 [508]
11
2[36]
21
4[57]
73
4[195] 73
4[195]
21
4[57] 16 [404]

FV605 Rev. A 8/6/2018
Page 5
L Brackets Installation
Required Tools:
For ease of installion, lay basin on its top surface on a cush-
ioned surface.
Use socket wrench to torque the screws (approximately 4-5
complete turns bottom out approximately 5 ft-lbs of torque).
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.
Drain Adapter Assembly
Installation
Torx Wrench:
T10 & T25
Socket Wrench:
5/16” & 3/8”
Non-toothed WrenchAllen Wrench:
3mm
12
17
13
18
For ease of installion, lay basin on its top surface on a cush-
ioned surface.
Use T25 torx wrench to torque the screws (approximately
4-5 complete turns and squeeze the gasket, approximately
2-3 ft-lbs of torque).
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.

FV605 Rev. A 8/6/2018
Page 6
Faucet Installation
Soap Dispenser Installation
For ease of installion, lay basin on its back.
Refer to faucet installation guide for details.
For ease of installion, lay basin on its back.
Install the soap spout on right or left soap hole as applicable.
Refer to soap dispenser installation guide for details.

FV605 Rev. A 8/6/2018
Page 7
Installing Mounting Bracket
• Secure the mounting bracket to the plywood cut-out with supplied washers, bolts and toggle an-
chors on the plywood.
Retrotting Hanger Bracket
Installation
Recommended for retrot:
• Measure the rough in dimensions on the wall. Top edge of the
cutout marked must be 2” below the basin top back edge.
• Cut the drywall to suitable size (30”x20”) and attach a min-
imum of 1/2” thick plywood to the wall stud and ush to the
drywall.
• Drill four ¾” holes in the plywood at the locations shown in the
graphic to the left. Then, install the supplied toggle anchors to
wall and secure the hanger bracket(s) directly to the plywood
with the supplied bolts.
• Install hanger bracket to wall per structural rough-in.
(Note: An offset might be necessary on applications using tile
to get the basin and mounting brackets ush with the wall and
mating bracket
• The plywood should not be visible after basin and shroud
installation.
• The bracket needs to be checked for level after installation.
Mounting
Bracket
21
19
20
Plywood
Wall Stud
Bolt supplied by
installer to attach
the plywood to
wall studs
Warning: Must be handled by at least 2 people
Warning: Ensure the basin back edge is completely supported in the wall bracket.
Avertissement : s’y prendre à deux minimum.
Avertissement : s’assurer que le bord arrière du bac est complètement soutenu par le support mural.
21
19
20
Plywood
Wall Stud
Bolt supplied by
installer to attach
the plywood to
wall studs
Hanger
Bracket
1 [25]
31
2[89]
4 [99]
31
2[89]

FV605 Rev. A 8/6/2018
Page 8
Soap Dispenser Bracket
and Bottle Installation
Refer to soap dispenser installation guide for details.
Installing with Carrier Option
Warning: Must be handled by at least 2 people
Avertissement : s’y prendre à deux minimum.
Refer to Carrier Rough-in & Installation guide for details.

FV605 Rev. A 8/6/2018
Page 9
P Trap Installation & Water
Supply Connection to Faucet
Adjust the tail piece base on drain outlet on the wall.
Grid Drain Installation
Connect the tail piece
to drain adapter
(threaded connection)
Shroud Installation:
• Align wall bracket as shown and install coarse screw on
each side. Mark the slots in the wall bracket on the wall.
14
Use T10 Torx wrench to attach the grid drain to basin.
Torque screws until the screw heads are ushed with the
screw pocket of grid drain.
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.
Suggested Final Step: Caulk/Silicon lavatory to the nished
wall for a water tight seal.
9
6
15
Step 1
15

FV605 Rev. A 8/6/2018
Page 10
Shroud Installation:
• Remove the wall bracket and drill 3/4” holes into the
center of the holes previously marked. (Note: For installation
with carrier, do NOT drill the two outside holes. For retrot
applications, the two outside holes are recommended.) En-
sure that wall studs are not immediately behind the marked
hole locations prior to drilling.
• Install anchor toggle bolts into previously drilled holes in
walls.
• Re-install wall bracket with coarse screws in previous lo-
cation. Then, fasten the wall bracket with 3/8” bolts through
each holes and into the toggle bolts.
• Place shroud on hanger hooks of wall bracket as shown.
Then, position the pivot of the shroud through the hole in the
wall bracket. (Note: the shroud will likely need to be rotated
upward slightly in order to install each pivot.
• After one pivot is installed, fasten the ange screw into
the pivot with the 3mm allen wrench. Then repeat this step
for the other side
• Rotate the shroud up to the basin until the threaded
hole in the L-bracket in visible through the slot in the shroud.
Then, install the screw shown, and repeat for the other side.
19
13
20
Step 2 Step 3
Step 5Step 4
16