3M 562 Datasheet

Instructions and Parts List
Description
The S-63 Manual Box Sealer is designed to
seal containers with an "L" shaped clip of tape
of equal leg lengths. The tape application is
made quic ly and easily with one pass of the
container across the box sealer top. The S-63
can be operated from the top of or recessed into
the pac ing counter. It is also recommended for
conveyor mounting.
Specifications
Tape: Most "Scotch" brand pressure-sensitive
cellophane, acetate fibre or film tapes.
Tape Width: 1/4 inch [6 mm] minimum to
5/8 inch [15 mm] maximum.
Tape Roll Diameter: Up to 5-1/2 inch [140 mm]
diameter on a 3 inch [76.2 mm] core.
Tape Lengths Dispensed:
It applies a 1-1/2 inch [38 mm] lg. "L" shaped
clip of tape with equal length legs.
Overall Dimensions: 10-1/2 inch [267 mm] lg. x
7 inch [178 mm] high x 5-1/4 inch [134 mm] wide
Weight: 10-3/4 lbs. [5 g] unpac aged;
11-3/4 lbs. [5.5 g] pac aged.
Tape Loading/Threading
1. Press tape roll against drum flange and thread
tape as shown in Figure 1.
2. Adhere end of tape to cutter mount grooved
surface.
3. The tape drum is positioned for 1/2 inch wide
tape. Refer to tape alignment adjustment for
other tape widths.
Figure 1
S-63 Manual Box Sealer
Model 562
Scotch
TM

Figure 5
Figure 2
Tape Not Flipping Up
1. Clean grooved surface of
cutter mount (H), Figure 3,
with solvent.
2. If tape still does not flip up,
sand grooved surface lightly
with a very fine sandpaper.
3. If tape still does not flip up,
replace cutter mount with new
part. Figure 7
Figure 6
Figure 3
Tape Not Sticking to
Bottom of Product
Refer to Figure 6
1. Loosen four screws (L) and
adjust frame to accomplish the
following:
a. Buffing roller (M) must be
1/64 inch to 1/32 inch
above the case cover.
b. Sealer arm and roller (N)
must be aligned with the
cover slot with no
interference.
c. Hammer must cut the next
length of tape before roller
(N) pivots below case
cover.
Adjustments
(Note correct position of all parts
before disassembly to ensure
proper reassembly.)
Tape Not Cutting
Refer to Figure 2
1. Loosen set screw (A) with 3/32
inch hex wrench provided and
adjust spring post (B) out to
increase hammer tension.
2. If tape still does not cut,
remove cotter pin (C) and
rotate hammer (D) 180° on the
hammer arm (E). Insert cotter
pin (C).
3. If tape still does not cut, rotate
nife bloc s (F) shown in
Figure 3 as follows:
a. Remove screw (G) and nut
using 1/16 hex wrench
provided (wrench flats are
also provided on the screw.
b. Remove cutter mount (H)
and rotate each nife bloc
(F) 180°. Reassemble
cutter mount, screw and
nut.
c. The two remaining edges
may be used by rotating
each nife bloc 180° on its
screw axis and following
step "b" above.
Tape Alignment
1. Adjust tape drum (J) as shown
in Figure 4 to center tape on
cutter mount.
Figure
Tape Curling Under
Appl ing Roller
1. Increase tape tension by
tightening adjustment nut (K)
shown in Figure 5.
Tape Breaking
1. Decrease tape tension by
loosening adjustment nut (K)
shown in Figure 5.
Sealer Arm Not Returning
Refer to Figures 7 and 8
1. Remove loc nut (P).
2. Hold idler stud (Q). Remove
washer (R), rotate washer
180° and replace on the idler
stud shaft.
3. Rotate the idler stud (Q)
cloc wise 60° to engage
washer peg in next frame slot.
4. Replace loc nut.

Timing the Mechanism
It is necessary to re-time the
dispenser when replacing the
sealer arm, idler gear, cutter
wheel or related parts.
Refer to Figures 9 and 10
1. Position the sealer arm (S)
against the frame.
2. Align the second tooth root,
point (T), of ratchet gear with
offset in frame above gear.
3. Align the washer peg (R) with
one of the frame slots and
engage the spring loops
against the pins in the idler
gear (U) and idler stud (Q).
4. Engage the idler gear with the
sealer arm and the ratchet
gear.
5. Turn the idler stud cloc wise
240° and position washer peg
in the slot.
6. Replace loc nut (P).
Lubrication
Routine lubrication of the box
sealer is not required. Lubricate
replacement moving parts as
follows:
1. Apply light film of SAE #30 oil
to bronze bearings.
2. Apply light coat of Lubriplate
630AA or equivalent to all
other moving part bearing
surfaces including gear teeth
and spring posts.
Do not lubricate tape drum
friction assembly parts.
Replacement Parts Illustration (Replacement Parts List on bac page.)
Figure 8
Figure 9
Figure 10

3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
Scotch is a trademark of 3M,
St. Paul, Minnesota 55144-1000
Litho U.S.A.
© 3M 1 8 34-7004-7252-4(H38.1)
Replacement Parts List
Ref Part
No. Number Description
1 18-9100-6015-3 3/32 x 7/8 Cotter Pin
2 18-9841-0815-1 No. 8 Internal Lockwa her
3 18-9851-1015-6 No. 10 External Lockwa her
4 18-4603-3003-0 10-24 x 3/8 Lg Binding Hd. Scr.
5 18-1756-3403-1 3/8-24 Ela tic Stop Nut
6 18-1708-3403-2 3/8-24 Hex Nut
7 70-7023-1970-1 3/8 Internal Lockwa her
8 70-8105-7710-9 Hammer Shaft A embly
9 70-8634-8000-3 Hammer Arm Spring
10 70-8261-5810-0 Clevi Arm A embly
11 70-8108-0710-0 Idler Gear Std A embly
12 70-8223-6240-9 Ratchet Gear
13 70-8690-8328-0 Bumper
14 70-8223-1010-1 Idler Gear A embly
15 70-8129-6810-8 Cutter Wheel Hub A embly
16 70-8612-3201-8 Foot Pad
17 70-8043-8927-1 Frame A embly
18 70-8121-6420-3 Tape Drum A embly
19 70-8105-6300-0 Connector Shaft
20 18-9260-6000-7 Spring Pin 3/32 Dia. x 7/8 Lg.
21 70-8105-6740-7 Drum Brake Shaft
22 70-8046-8300-4 Trip Pin Plate
23 70-8261-6510-5 Sealing Arm A embly
24 70-8105-6422-2 Cutter Shaft A embly
25 70-8635-5800-6 Tor ion Return Spring
26 70-8261-7350-5 Trip Pin Arm A embly
27 70-8126-1320-9 Buffing Roller A embly
28 70-8697-6890-6 Spacer
29 70-8601-6170-5 Knife Block
Ref Part
No. Number Description
30 70-8659-3675-4 Spring Wa her
31 70-8659-1600-4 Friction Wa her
32 70-7023-7780-8 4-40 Nut Light Hex "FLEXLOC"
#21 FA440
33 70-8606-1210-3 Hammer
34 70-8659-4225-7 Thru t Wa her 33/64 ID x 3/4 OD
35 70-8635-3000-5 Ratchet Key Spring
36 70-8656-5875-4 Cutter Mount Scr.
37 70-8659-3800-8 Pre ure Wa her (Rubber)
38 70-8697-6883-1 Wa her 26/64 ID x 5/8 OD
39 70-8658-9000-1 Wa her 17/64 ID x 9/16 OD
40 70-8658-9100-9 Wa her 33/64 ID x 1 OD
41 70-8658-8900-3 Wa her with Peg
42 70-8045-6703-3 Cutter Mount
43 70-8652-6800-0 Ratchet Key
44 26-8092-5015-7 Thru t Wa her "OILITE" TT 1001-1
45 70-8128-2990-4 Sleeve A embly
46 70-8261-6630-1 Spring Arm
47 78-8023-2190-7 Drum  Tape
48 78-8023-2613-8 Retainer  Tape
49 78-8052-6293-4 Wa her  Friction
50 70-8659-1600-4 Wa her  Friction
51 26-1002-4949-4 Screw  Self-Tap, Thd. Forming,
Pla titie Pan Hd. Phillip Dr.
#6-19 x 3/8 Lg.
52 18-1756-3403-1 Nut  Self Lock 3/8-24 NF
53 78-8113-6846-9 Shaft  Drum Brake
54 26-1001-6402-4 Screw  Cap Soc. Hd., 8-32 x 1/2 Lg.
Equipment Warranty and Limited Remedy: THE FOLLOW NG WARRANTY S MADE N L EU OF ALL OTHER WARRANT ES,
EXPRESS OR MPL ED, NCLUD NG, BUT NOT L M TED TO, THE MPL ED WARRANTY OF F TNESS FOR A PART CULAR
PURPOSE AND ANY MPL ED WARRANTY AR S NG OUT OF A COURSE OF DEAL NG, A CUSTOM OR USAGE OF TRADE:
3M warrant that it Scotch brand dispensers will be free from defect for ninety (90) day after delivery. If any part i proved to be
defective within the warranty period, then the exclu ive remedy and 3M and eller ole obligation hall be, at 3M option, to repair or
replace the part, provided the defective part i returned immediately to 3M factory or an authorized ervice tation de ignated by 3M. A
part will be pre umed to have become defective after the warranty period unle the part i received or 3M i notified of the problem no
later than five (5) calendar day after the warranty period. If 3M i unable to repair or replace the part within a rea onable time, then 3M, at
it option, will replace the equipment or refund the purcha e price.
Limitation of Liability: 3M and eller hall not be liable for direct, indirect, pecial, incidental or con equential damage ba ed upon
breach of warranty, breach of contract, negligence, trict liability or any other legal theory.
The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a written agreement igned by
authorized officer of 3M and eller.
How To Order Replacement Parts
1. Refer to replacement parts illustration to find part
needed and reference number.
2. Refer to parts list for correct part number.
3. Order by part number, part name, dispenser
catalog number and model number.
4. Replacement parts and part prices available direct
from:
3M/Tape Dispenser Parts
241 Venture Drive
Amer , WI 54001-1325
800/344 9883
FAX # [phone]
5. Machine repair service ship direct to:
Tape Equipment Repair Services
241 Venture Drive
Amer , WI 54001-1325
Minimum billing on parts orders will be $25.00.
Replacement part prices available on request.
$10.00 restocking charge per invoice on returned parts.
3