3M 3M-Matic a20 Datasheet

Instructions and Parts List
a20 Type 10700
Adjustable
Case Sealer
with
AccuGlide 2+
Taping Heads
"3M-Matic"and "AccuGlide" are Trademarks of,
3M St. Paul, MN 55144-1000
Printed in U.S.A.
© 3M 2011 44-0009-2060-1 (F060311-NA)
Serial No.
For reference, record machine serial number here.
Important Safety
Information
Spare Parts
™
3M-Matic ™BEFORE INSTALLING
OR OPERATING THIS
EQUIPMENT
Read, understand, and
follow all safety and
operating instructions.
It is recommended you
immediately order the
spare parts listed in the
"Spare Parts/Service
Information" section.
These parts are expected
to wear through normal
use, and should be kept
on hand to minimize
production delays.
3M Industrial Adhesives and Tapes
3M Center, Building 220-5E-06
St. Paul, MN 55144-1000

This instruction manual covers safety aspects,
handling and transport, storage, unpacking,
preparation, installation, operation, adjustments,
maintenance, troubleshooting, repair work and
servicing plus parts list of the 3M-MaticTM a20
Adjustable case sealer.
3M Industrial Adhesives and Tapes
3M Center, Building 220-5E-06
St. Paul, MN 55144-1000
Edition April 2011
Copyright 3M 2011
All rights reserved
The manufacturer reserves the right to change
the product at any time without notice.

i
4000563
I
N
T
E
R
T
E
K
For Industrial Use Only
3M-Matic™, AccuGlide™and Scotch™
are Trademarks of
3M St. Paul, MN 55144-1000
Printed in U.S.A.
3M Industrial Adhesives and Tapes
3M Center, Building 220-5E-06
St. Paul, MN 55144-1000
To Our Customers:
This is the 3M-Matic™/AccuGlide™/Scotch ®equipment you ordered.
It has been set up and tested in the factory with Scotch ®tapes.
If technical assistance or replacement parts are needed, call or fax the appropriate number
Included with each machine is an Instructions and Parts List manual.
Technical Assistance / Replacement Parts and Additional Manuals:
Contact your local service provider. Provide the customer support coordinator with the
model/machine name, machine type, and serial number that are located on the identication plate
(For example: Model a20 - Type 10700 - Serial Number 13282).
Identication Plate
Replacement Parts and Service Information

THIS PAGE IS BLANK

TABLE OF CONTENTS - MANUAL 1: a20 Adjustable Case Sealer
(For Taping Head Information - See MANUAL 2: AccuGlide™ 2+ STD 2 Inch Taping Heads)
a20 Adjustable Case Sealer Page
Cover Page
Replacement Parts and Service Information ........................................................................i - ii
Table of Contents ................................................................................................................. iii - v
Acronyms and Abbreviations ................................................................................................vi
1. Introduction
1.1 Manufacturing Specifications / Description / Intended Use ......................................... 1 - 2
1.2 How to Read and Use the Manual / Reference Documents ......................................... 2
1.2.1 Importance of the Manual .................................................................................. 2
1.2.2 Manual Maintenance ......................................................................................... 2
1.2.3 Consulting the Manual ........................................................................................ 2
1.2.4 How to Update the Manual in Case of Modifications ...........................................2
2. General Information
2.1 Identification Data .........................................................................................................3
2.2 Warranty / Contents ......................................................................................................4
3. Safety
3.1 General Safety Information ...........................................................................................5
3.2 Signal Words Explanation ............................................................................................. 5
3.3 Table of Warnings ..........................................................................................................6 - 7
3.4 Operator’s Qualifications Definition .............................................................................. 8
3.5 Number of Operators ....................................................................................................8
3.6 Safe Use of the Machine Instructions ...........................................................................8
3.7 Residual Hazards .......................................................................................................... 8
3.8 Prevent Other Hazards - Recommendations and Measures ........................................8
3.9 Personal Safety Measures ........................................................................................... 8
3.10 Incorrect / Predictable Actions Not Allowed ..................................................................8
3.11 Operator's Required Skill Levels .................................................................................. 9
3.12 Component Locations .................................................................................................. 10
3.13 Table of Warnings and Replacement Labels ................................................................ 11
4. Technical Specifications
4.1 Power Requirements ....................................................................................................12
4.2 Operating Rate ............................................................................................................. 12
4.3 Operating Conditions ....................................................................................................12
4.4 Tape ..............................................................................................................................12
4.5 Tape Width ....................................................................................................................12
4.6 Tape Roll Diameter ....................................................................................................... 13
4.7 Tape Application Leg Length - Standard .......................................................................13
Tape Application Leg Length - Optional
4.8 Box Board .....................................................................................................................13
4.9 Box Weight and Size Capacities ................................................................................... 13
4.10 Machine Noise Levels ................................................................................................... 13
4.11 Machine Dimensions ..................................................................................................... 14
4.12 Setup Recommendations .............................................................................................. 14
iii 2011 April
a20-NA