3M 251 User manual

Manuclave Anchor Clamp
User Instructions
Part Number Material Length Width Anchorage
Opening
Connection
Opening Weight Standard / Regulation
251 Stainless Steel 16 in. (40.6cm) 6.8 in. (17cm) 4.4 in. (11cm) 1.4 in. (3.6cm) 12 lbs. (340g) OSHA 1910.66,
OSHA 1926.502
252 Stainless Steel 16 in. (40.6cm) 8 in. (20.3cm) 5.5 in. (14cm) 1.4 in. (3.6cm) 13 oz. (369g) OSHA 1910.66,
OSHA 1926.502
General Safety Information
These User Instructions are not to be removed except by the
user of this equipment. User Instructions must always be
available to the user.
Compliant fall protection and emergency rescue systems
help prevent serious injury during fall arrest. Users must
read and understand the User Instructions provided with the
product and be properly trained by their employer prior to
use per OSHA 29 CFR 1910.66 and 1926.503 or applicable
local standards. Misuse or failure to follow warnings and
instructions may result in serious personal injury or
death. For proper use, see supervisor, User Instructions, or
call Technical Service at 1-800-560-1094.
Purpose
The 3M Manuclave Anchor Clamps are designed to be used
as part of a personal fall arrest system, to help limit the fall
arrest forces in the event of a fall.
Use Instructions
1. Failure to follow all instructions and limitations on the
use of Manuclave Anchor Clamps may result in serious
personal injury or death.
2. Before using a personal fall arrest system, employees
shall be trained in accordance with the requirements of
OSHA’s 29 CFR 1910.66 in the safe use of the system
and its components.
3. Personal fall arrest systems, including Manuclave
Anchor Clamps, shall be inspected prior to each use
for wear, damage, and other deterioration. Defective
components must be immediately removed from service,
in accordance with the requirements of OSHA’s 29 CFR
1910.66 and 1926.502.
4. The complete fall protection system must be planned
(including all components, calculating fall clearance, and
swing fall) before using.
5. Users must have a rescue plan, and the means at
hand to implement it, that provides the prompt rescue
of employees in the event of a fall or assures that
employees are able to rescue themselves.
6. Store Manuclave Anchor Clamps in a cool, dry, clean
environment, out of direct sunlight, when not in use.
7. After a fall occurs, the Manuclave Anchor Clamp must
be removed from service and destroyed immediately.
Use Limitations
1. Manuclave Anchor Clamps are designed for single users
only.
2. Per OSHA’s 29 CFR1910.66 and 1926.502 Manuclave
Anchor Clamps must only be used on structures capable
of supporting at least at least 5,000 pounds (22.2 kN)
per employee attached, or shall be designed, installed,
and used as part of a complete personal fall arrest system
which maintains a safety factor of at least two, under the
supervision of a qualified person.
3. Manuclave Anchor Clamps are designed to be used in
temperatures ranging from -40ºF to +130ºF (-40°C to
+54°C).
4. Do not expose Manuclave Anchor Clamps to chemicals
or harsh solutions which may have a harmful effect.
Contact 3M Technical Service with any questions.
5. Caution must be taken when using Manuclave Anchor
Clamps near moving machinery, electrical hazards,
sharp edges, or abrasive surfaces, as contact may cause
equipment failure, personal injury, or death.
6. Minors, pregnant women and anyone with a history
of either back or neck problems should not use this
equipment.
7. Do not use or install equipment without proper training
from a “competent person” as defined by OSHA’s 29
CFR 1926.32(f).
8. Only 3M, or persons or entities authorized in writing by
3M, shall make repairs or alterations to the equipment.
Compatibility Limitations
All 3M Manuclave Anchor Clamps must only be coupled to
compatible connectors. OSHA’s 29 CFR 1926.502 prohibits
snaphooks from being engaged to certain objects unless two
requirements are met: it must be a locking type snaphook,
and it must be “designed for” making such a connection.
“Designed for” means that the manufacturer of the snaphook
specifically designed the snaphook to be used to connect to
the equipment listed. The following connections must be
avoided, as they are conditions that can result in rollout when
a nonlocking snaphook is used:
• Direct connection of a snaphook to horizontal lifeline.
• Two (or more) snaphooks connected to one D-ring.
• Two snaphooks connected to each other.
• A snaphook connected back on its integral lanyard.
• A snaphook connected to a webbing loop or webbing
lanyard.
• Improper dimensions of the D-ring, rebar, or other
connection point in relation to the snaphook dimensions
that would allow the snaphook keeper to be depressed by
a turning motion of the snaphook.
Performance
All Manuclave Anchor Clamps meet a 5,000 lb. tensile load.
WARNING

Manuclave Anchor Clamp
User Instructions
Product Warranty, Limited Remedy, and
Limitation of Liability
WARRANTY: THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. Equipment offered by 3M is warranted against factory defects in workmanship and materials for
a period of one year from date of installation or first use by the original owner.
LIMITED REMEDY: Upon notice in writing, 3M will promptly repair or replace all defective items. 3M reserves the right to
elect to have defective item returned to its plant for inspection before making a repair or replacement. Warranty does not cover
equipment damage resulting from wear, abuse, damage in transit, or other damage beyond the control of 3M. 3M shall be the
sole judge of product condition and warranty options. This warranty applies only to original purchaser and is the only warranty
applicable to our products. A Return Goods Authorization Number (RGA) must be issued by 3M on all returns for warranty
consideration. All returns must be shipped to 3M freight prepaid. Please contact 3M customer service department at
1-800-560-1094 for warranty assistance.
LIMITATION OF LIABILITY: In no event will 3M be liable for any indirect, incidental, special or consequential damages
including, but not limited to loss of profits, in any way related to the products regardless of the legal theory asserted.
Please recycle. Printed in USA.
© 2010
3M is a trademark of 3M Company,
used under license in Canada.
All rights reserved.
IM-0028 Rev A 12-2010
3M Occupational Health &
Environmental Safety Division
4551 Raceway Drive SW
Concord, NC 28027
USA
Phone [phone]
Fax [phone]
www.SafeWaze.com
www.3M.com/OccSafety
Installation
The Manuclave Anchor Clamp must be installed on structures
capable of meeting the anchorage strength requirements of
OSHA 29 CFR 1910.66 and 1926.502.
Squeeze handle together to open the top section of the
Manuclave Anchor Clamp and slip over structure. Rotate
handle to allow the circular part of clamp to position itself
around the structure. Release the handle to allow the hooks to
engage on each side.
Do not use the Manuclave Anchor Clamp on angled
structures, or at the end of a run where it could slide off the
end of the structure.
Do not use the Manuclave Anchor Clamp where loading is
offset to the center of the Manuclave Anchor Clamp.
Inspection
All Manuclave Anchor Clamps must be inspected prior to
each use, and additionally by an OSHA defined competent
person other than the user annually.
Any equipment that has been subjected to the forces of
arresting a fall must be removed from service.
All Manuclave Anchor Clamps must be free of cracks, sharp
edges, deformation, corrosion, chemical attack, alteration,
excessive heating or wear.
All markings must be legible and attached to the product.
If inspection reveals any defect, inadequate maintenance, or
unsafe condition, remove from service and destroy.
Note: Only manufacturer, or entities authorized in
writing by the manufacturer, may make repairs to the
product.
Cleaning and Maintenance
No cleaning or maintenance is required for this product.
If inspection reveals any defect, remove from service and
destroy.