3M 5936792 User manual

Technical File: 3M TF0369
3M United Kingdom PLC 3M Confidential
DocumentIssueDate:26/06/2013
DocumentIssueRef:DV‐2563‐0347‐5_Iss2‐Master
EUROPEAN MASTER TEXT – USER INSTRUCTION TEXT
Product: 3M™ Safety Spectacle
Packaging item: User Instructions
USER INSTRUCTIONS: 3M™ Safety Spectacles
Safety Eyewear conforming to EN 166
WARNING
Particular attention should be given to warning statements where indicated.
Always be sure that the complete product is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
Proper selection, training, use and appropriate maintenance are essential in order for the product to help
protect the wearer.
Always use both hands to put on and remove eyewear.
Failure to follow all instructions on the use of these personal protection products and/or failure to properly
wear the complete product during all periods of exposure may adversely affect the wearer's health, lead to
severe or life threatening illness or permanent disability.
For suitability and proper use follow local regulations, refer to all information supplied or contact a safety
professional/3M representative.
See all instructions for use and save for continuing reference.
Elasticated textile headbands may contain natural rubber latex.
Other products do not contain natural rubber latex.
Standard and Approval:
These products meet the requirements of EN 166
Check product marking for further information on intended use.
These products meet the Basic Safety Requirements as laid out in Annex II of the European Community
Directive 89/686/EEC, and have been examined at the design stage by:
ECS GmbH - European Certification Service, Huettfeldstrasse 50, 73430 Aalen Germany (Notified body
number 1883)
INSPEC International Limited, 56 Leslie Hough Way, Salford, Greater Manchester M6 6AJ, UK (Notified Body
number 0194).
BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes, MK5 8PP, UK (Notified body number 0086).
Institut National De Recherche Et De Securite, Centre de Lorraine, Rue du Morvan, CS 60027, 54519
Vandoeuvre les Nancy Cedex, France (Notified Body number 0070)
Certottica Scarl, Zona Industriale Villanova, I- 32013 Longarone BL, Italy (Notified Body number 0530)
Name and address of Legal Manufacturer:
3M United Kingdom PLC, 3M Centre, Cain Road, Bracknell, RG12 8HT, 08706080060


Technical File: 3M TF0369
STORAGE AND TRANSPORTATION
Follow the manufacturer's recommendation for storage.
Maximum Relative Humidity
Temperature Range
Date of manufacture (mm/yyyy)
See package for details
Discard the product within 5 years from the date of manufacture or immediately if damaged.
When transporting this product use original packaging.
Store in original packaging and keep away from abrasives, solvents or solvent vapours.
CLEANING AND DISINFECTION
Eyewear should be cleaned using soap and water or 3M™ Cleaning Solution.
Pat dry with a soft cloth or tissue.
LIMITATIONS OF USE
Inspect the eye protector regularly; pitted or scratched lenses or damaged frames may seriously reduce
protection.
Replace the product or lens (where appropriate) when this occurs.
If in doubt, check with the manufacturer.
3M Safety Eyewear is intended to provide a universal fit.
Materials which come into contact with the wearer's skin could cause allergic reaction to susceptible
individuals.
Eye protectors against high speed particles worn over standard opthalmic spectacles may transmit impact
energy, creating a hazard to the wearer.
If the frame and lens markings for mechanical strength differ, the lower level applies to the complete eye
protector.
If protection is required at extremes of temperature then select safety eyewear with the letter T immediately
after the impact letter, i.e. FT.
A - Frame Marking
1 - Manufacturer (3M)
2 - Model name or number
3 - Number of the standard EN 166
4 - Mechanical Strength (S= Increased Robustness, F = High Speed Particles, low energy impact)
5 - Designed for small head
6 - Approval mark
B - Lens Marking
1 - Filter Code Number (2 or 2C = Ultraviolet, 4 = Infrared, 5 = Sunglare without IR protection, 6 = Sunglare
with IR protection)
2 - Shade number (without code number = welding filter)
3 - Manufacturer (3M)
4 - Optical Class
5 - Mechanical Strength (see frame marking)
6 - Resistance to surface damage by fine particles
7 - Resistance to fogging
3M United Kingdom PLC 3M Confidential

Technical File: 3M TF0369
3M United Kingdom PLC 3M Confidential
