A-Tach Mounts 50206 User manual

A-Tach # 50206
Designed for: Buick Enclave 2018 - 20__
ST-1 A-Tach
Mounts
NOTICE: A-Tach Mounts will not be responsible for
any damage to the vehicle due to the installation
and/or use of the product. The product has been
tested to fit securely to the listed vehicles.
Instructions are provided for your convenience.
You are responsible for the use of the product and
to determine if you have the skill to attach the
product without causing damage to your vehicle or
the product.
Read all instructions and view the photos before
attaching this product.
For best results, hold the vehicle mount over the place where the mount attaches to the dash BEFORE
attaching the device holder to the vehicle mount to ensure a proper fit with the location. Most often the
mount will appear to be a little too big or small for the intended location. The vehicle mount must be
installed BEFORE a device holder is screwed onto the vehicle mount.
Once screwed together the products are considered used and non-refundable.
The vehicle mount is not designed to be attached and taken off the vehicle repeatedly or on a regular basis.
Once it is attached, it should remain attached until you would like to permanently remove it.
WARNING: AVOID extreme heat conditions. It can damage the device and the mount.
(1) Clean the area where the mount will attach. The
mount will attach into the two seams illustrated
with the arrows in the photo.
(2) Insert the thin edge of the seam tool into the
lower seam under the padded portion of the dash
to open the seam a little.
(3) Remove the covering from the tape. Press the
thin lower edge of the mount all the way into the
seam next to the seam tool.
(4) Remove the seam tool and insert it into the
seam between the display and frame illustrated in
the photo.
See additional instructions on the back side.

(5) Press forward on the mount until the thin upper
edge of the mount goes into the seam next to the
seam tool.
(6) The mount attaches over both sides of the
display. The tape will not leave any residue if the
mount is removed in the future.
Warranty and Returns
A-Tach Mounts Limited Warranty
A-Tach warrants the product to be free of all defects in materials and workmanship for a period of six
(6) months from the date of purchase. This warranty extends to the original buyer. Damaged products
caused by anything outside of shipping damage are not covered by this warranty.
Within the period of this warranty, A-Tach has the option to repair or replace the item or refund the
purchase price. Any replacement parts will be done on an exchange basis. All repairs and service must
be done by A-Tach. Product must be delivered to A-Tach during the warranty time along with proof of
purchase price and date. The shipping and packaging costs will be the buyer’s responsibility. Labor
costs and parts to repair will be A-Tach Mounts responsibility.
A-Tach Mounts will not be responsible for any damage to the vehicle or product due to the installation
and/or use of the product. A-Tach is not responsible for damages caused by extreme heat conditions.
Any above exclusion may not apply in states that do not allow the exclusion or limitation. This warranty
gives you specific legal rights. You also may have other rights which vary from state to state.
Returns
Before any product may be returned, A-Tach must give prior approval. An RMA# (Return Merchandise
Authorization Number) needs to be given to the buyer to return a product. All returns must be within
(30) days of the invoice date and include proof of purchase. Any returned product must be undamaged
and in like new condition. Returned product must be scratch free with no additional holes or screw
marks on the product.
A-Tach reserves the right to withhold any refund if the product is believed to be damaged. A return
must include a copy of the original order or invoice. All parts and components that were shipped with
the original product must be included with the returned product.
Contact Information:
A-Tach Mounts
Clarkston, WA 99403
[e-mail]