A-Tach Mounts ST-1 User manual

A-Tach # 50080
Designed for: Ford Expedition 2007-2017
ST-1 A-Tach
Mobile Device Mounts
NOTICE: A-Tach Mounts will not be responsible for
any damage to the vehicle due to the installation
and/or use of the product. The product has been
tested to fit securely to the listed vehicles.
Instructions are provided for your convenience.
You are responsible for the use of the product and
to determine if you have the skill to attach the
product without causing damage to your vehicle or
the product.
Read all instructions and view the photos before
attaching this product.
For best results, hold the vehicle mount over the place where the mount attaches to the dash BEFORE
attaching the device holder to the vehicle mount to ensure a proper fit with the location. Most often the
mount will appear to be a little too big or small for the intended location. The vehicle mount must be
installed BEFORE a device holder is screwed onto the vehicle mount.
Once screwed together the products are considered used and non-refundable.
The vehicle mount is not designed to be attached and taken off the vehicle repeatedly or on a regular basis.
Once it is attached, it should remain attached until you would like to permanently remove it.
WARNING: AVOID extreme heat conditions. It can damage the device and the mount.
(1) See additional notes on back. Clean the area
where the mount will attach. Remove the covering
from the tape. The tape will not leave any residue if
the mount is removed in the future. Insert the
seam tool into the seam between the frame around
the radio and the padded dash top. See photo.
(2) Insert the lower edge of the mount into the
seam next to the seam tool. Press the mount all
the way into the seam until the back side of the
mount touches the padded dash top.
(3) Pull out the seam tool and insert it into the
seam at the very front of the dash top tray.
Between the tray and the padded dash top. Not the
seam of the speaker grill.
(4) Press the mount forward and hook the front
edge of the mount into the seam next to the seam
tool. Press down on the mount to make sure the
tape makes connection to the dash panel.
See additional instructions on the back side.

Additional Instruction Notes:
1. The mount will attach onto the center area of the dash top tray. There are tabs under the dash top
tray on the far left and right corners that prevent the mount from attaching onto those areas. The mount
will need to be positioned in about one inch from the left or right sides of the dash top tray.
Warranty and Returns
A-Tach Mounts Limited Warranty
A-Tach warrants the product to be free of all defects in materials and workmanship for a period of six
(6) months from the date of purchase. This warranty extends to the original buyer. Damaged products
caused by anything outside of shipping damage are not covered by this warranty.
Within the period of this warranty, A-Tach has the option to repair or replace the item or refund the
purchase price. Any replacement parts will be done on an exchange basis. All repairs and service must
be done by A-Tach. Product must be delivered to A-Tach during the warranty time along with proof of
purchase price and date. The shipping and packaging costs will be the buyer’s responsibility. Labor
costs and parts to repair will be A-Tach Mounts responsibility.
A-Tach Mounts will not be responsible for any damage to the vehicle or product due to the installation
and/or use of the product. A-Tach is not responsible for damages caused by extreme heat conditions.
Any above exclusion may not apply in states that do not allow the exclusion or limitation. This warranty
gives you specific legal rights. You also may have other rights which vary from state to state.
Returns
Before any product may be returned, A-Tach must give prior approval. An RMA# (Return Merchandise
Authorization Number) needs to be given to the buyer to return a product. All returns must be within
(30) days of the invoice date and include proof of purchase. Any returned product must be undamaged
and in like new condition. Returned product must be scratch free with no additional holes or screw
marks on the product.
A-Tach reserves the right to withhold any refund if the product is believed to be damaged. A return
must include a copy of the original order or invoice. All parts and components that were shipped with
the original product must be included with the returned product.
Contact Information:
A-Tach Mounts
Clarkston, WA 99403
[e-mail]