A-Tach Mounts 50232 User manual

A-Tach # 50232
Designed for: Honda Fit 2015-20__
ST-1 A-Tach
Mounts
NOTICE: A-Tach Mounts will not be responsible for
any damage to the vehicle due to the installation
and/or use of the product. The product has been
tested to fit securely to the listed vehicles.
Instructions are provided for your convenience.
You are responsible for the use of the product and
to determine if you have the skill to attach the
product without causing damage to your vehicle or
the product.
Read all instructions and view the photos before
attaching this product.
For best results, hold the vehicle mount over the place where the mount attaches to the dash BEFORE
attaching the device holder to the vehicle mount to ensure a proper fit with the location. Most often the
mount will appear to be a little too big or small for the intended location. The vehicle mount must be
installed BEFORE a device holder is screwed onto the vehicle mount.
Once screwed together the products are considered used and non-refundable.
The vehicle mount is not designed to be attached and taken off the vehicle repeatedly or on a regular basis.
Once it is attached, it should remain attached until you would like to permanently remove it.
WARNING: AVOID extreme heat conditions. It can damage the device and the mount.
(1) Clean the area where the mount will attach. The
front of the mount will attach into the seam
illustrated with the arrow in the photo.
NOTE: This is a very tight seam.
(2) The lower edge of the mount will attach into
the seam illustrated with the arrow in the photo.
(3) Press the seam tool into the seam. This will help
to open the seam for the mount to go into. NOTE:
The mount will only attach onto the area just
to the left of the vent center.
(4) Remove the covering from the tape. Press the
front edge of the mount all the way into the seam.
NOTE: The edge of the mount will not go into
the seam in any other place.
See additional instructions on the back side.

(5) Place your fingers behind the face of the mount
and flex the lower edge of the mount into the lower
seam. Using two hands will work best.
(6) The mount attached. The tape will not leave
any residue if the mount is removed in the future.
Warranty and Returns
A-Tach Mounts Limited Warranty
A-Tach warrants the product to be free of all defects in materials and workmanship for a period of six
(6) months from the date of purchase. This warranty extends to the original buyer. Damaged products
caused by anything outside of shipping damage are not covered by this warranty.
Within the period of this warranty, A-Tach has the option to repair or replace the item or refund the
purchase price. Any replacement parts will be done on an exchange basis. All repairs and service must
be done by A-Tach. Product must be delivered to A-Tach during the warranty time along with proof of
purchase price and date. The shipping and packaging costs will be the buyer’s responsibility. Labor
costs and parts to repair will be A-Tach Mounts responsibility.
A-Tach Mounts will not be responsible for any damage to the vehicle or product due to the installation
and/or use of the product. A-Tach is not responsible for damages caused by extreme heat conditions.
Any above exclusion may not apply in states that do not allow the exclusion or limitation. This warranty
gives you specific legal rights. You also may have other rights which vary from state to state.
Returns
Before any product may be returned, A-Tach must give prior approval. An RMA# (Return Merchandise
Authorization Number) needs to be given to the buyer to return a product. All returns must be within
(30) days of the invoice date and include proof of purchase. Any returned product must be undamaged
and in like new condition. Returned product must be scratch free with no additional holes or screw
marks on the product.
A-Tach reserves the right to withhold any refund if the product is believed to be damaged. A return
must include a copy of the original order or invoice. All parts and components that were shipped with
the original product must be included with the returned product.
Contact Information:
A-Tach Mounts
Clarkston, WA 99403
[e-mail]