Aaeon HSB-668I User manual

Half-size CPU Card HSB-668I
HSB-668I
Onboard VIA Mark CoreFusion CPU
Half-Size Card
Realtek 8100C/8110S Ethernet
AC97 Codec Audio
HSB-668I Manual Rev. A 2nd Ed.
April 2008

Half-size CPU Card HSB-668I
i
Copyright Notice
This document is copyrighted, 2008. All rights are reserved. The
original manufacturer reserves the right to make improvements
to the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated,
or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information
provided in this manual is intended to be accurate and reliable.
However, the original manufacturer assumes no responsibility
for its use, or for any infringements upon the rights of third
parties that may result from its use.
The material in this document is for product information only
and is subject to change without notice. While reasonable
efforts have been made in the preparation of this document to
assure its accuracy, AAEON assumes no liabilities resulting
from errors or omissions in this document, or from the use of the
information contained herein.
AAEON reserves the right to make changes in the product
design without notice to its users.

Half-size CPU Card HSB-668I
ii
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
 Award is a trademark of Award Software International, Inc.
 VGA is a trademarks of International Business Machines
Corporation.
 DOC2000 is a registered trademarks of M-system Co., Ltd
 Microsoft Windows®is a registered trademark of Microsoft Corp.
 VIA is a trademark of VIA Technology, Inc.
 IBM, PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
 Winbond is a trademark of Winbond Electronic Corp.
Please be notified that all other products’ name or trademarks
not be mentioned above are properties of their respective
owners.

Half-size CPU Card HSB-668I
iii
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 Floppy Cable
• 1 ATA-100 Cable
• 1 USB Cable
• 1 Keyboard Cable
• 1 Serial + Parallel Cable
• 1 ATX Cable
• 1 Serial Cable
• 1 Two Serial Ports Cable
• 1 Quick Installation Guide
• 1 Utility CD
• 1 HSB-688I Half-size CPU Card
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.

Half-size CPU Card HSB-668I
iv
Contents
Chapter 1 General Information
1.1 Introduction................................................................1-2
1.2 Features....................................................................1-3
1.3 Specifications............................................................1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions....................................................2-2
2.2 Location of Connectors and Jumpers .......................2-3
2.3 Mechanical Drawing..................................................2-4
2.4 List of Jumpers..........................................................2-5
2.5 List of Connectors .....................................................2-6
2.6 Setting Jumpers ........................................................2-8
2.7 COM2 Pin 9 Function (RIB or +5V ) Selection (JP1) .......2-9
2.8 Clear CMOS (JP2) ....................................................2-9
2.9 LCD Voltage Selection (JP3) ....................................2-9
2.10 DOC2000 Address (Selection By BIOS).................2-9
2.11 Front Panel Connector (FP1)..................................2-9
2.12 Front Panel Connector (FP2)..................................2-10
2.13 RS232 Serial Port Connector(COM1/COM3/COM4)2-10
2.14 RS232/422/485 Serial Port Connector (COM2)......2-10
2.15 IrDA Connector (IR1)...............................................2-11
2.16 LPT Port Connector (LPT1) ....................................2-11
2.17 USB Connector (USB1) ..........................................2-12

Half-size CPU Card HSB-668I
v
2.18 Fan Connector (FAN1)............................................2-12
2.19 AC97 Connector (CN1)...........................................2-12
2.20 ATX Power Control Connector (CN2).....................2-13
2.21 LAN LED Connector (CN3/CN4).............................2-13
2.22 18/24Bit TTL Channel Connector (CN5).................2-13
2.23 36Bit TTL Channel Connector (CN6)......................2-14
2.24 LVDS Channel Connector (CN7)............................2-15
2.25 PS2 Keyboard/Mouse Connector (CN8).................2-15
2.26 Internal Keyboard Connector (CN9)........................2-16
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization. ..................................3-2
3.2 Award BIOS Setup....................................................3-3
Chapter 4 Driver Installation
4.1 Installation.................................................................4-3
Appendix A Programming the Watchdog Timer
A.1 Programming ............................................................A-2
Appendix B I/O Information
B.1 I/O Address Map.......................................................B-2
B.2 1st MB Memory Address Map ...................................B-3
B.3 IRQ Mapping Chart...................................................B-4
B.4 DMA Channel Assignments......................................B-4

Half-size CPU Card HSB-668I
Chapter 1 General Information 1- 1
General
Chapter
1
Information

Half-size CPU Card HSB-668I
Chapter 1 General Information 1- 2
1.1 Introduction
HSB-668I is a new standard ISA bus half-size CPU Card with
onboard VIA Mark CoreFusion 533MHz processor integrating with
North Bridge. It supports up to 128MB memory on board and is
with one SO-DIMM that memory can support up to 512MB. The
HSB-668I performs as a strengthened single board computer with
low power consumption while no CPU fan required.
This product is integrated AGP 4X 2D/3D video accelerator with 2
channel TTL interface. It supports 36bit LVDS LCD/CRT, and up
to 32 MB frame buffer using system memory.
Excellent connectivity is provided by embedded 10/100Mbps or
Gigabit Ethernet connection. The HSB-668I also offers
comprehensive I/O support, including 3 USB ports for connecting
the latest peripherals and four serial ports for industry standard
applications. Other onboard feature is include a parallel port, an
IrDA port, and an AC-97 SoundBlaster compatible audio. The
SSD solution supports DOC2000 as external storage.
Overall, this powerful CPU card aims to be your most effective
choice and perform low power applications at real affordable price!

Half-size CPU Card HSB-668I
Chapter1GeneralInformation1-3
1.2 Features
• Onboard VIA CoreFusion 533MHz Processor (Fanless)
• Onboard Memory supports up to 128MB
• One SODIMM SDRAM, Memory Up To 512MB
• Integrated ProSavage4 Graphic, 2D/3D VGA Support
• 2 Channel 36-bit LVDS LCD Support
• Integrated AC97 Codec Audio (Daughter Board
Optional)
• Two 10/100 Base-TX Ethernet (One 10/100 & GbE
Optional)
• DOC2000 PC-104 Interface Socket
• Two Ultra ATA 100 Channel
• Supports PC-104 Interface Socket
• 3 USB 1.1 / 1 Parallel / 1 IrDA Port
• 4 COM Ports ( 3 RS-232, 1 RS-232/422/485)
• Watchdog Function 1 ~ 255 Sec.
• ISA High-driver Support

Half-size CPU Card HSB-668I
Chapter 1 General Information 1- 4
1.3 Specifications
System
 FormFactor ISAHalf-sizeSBC
 Processor Onboard VIA Mark
CoreFusion 533MHz CPU
 System Memory 1 x 144-pin 3.3V SDR
SODIMM Socket up to
512MB (on board
memory supports up to
128MB), supports
PC100/133 types
 Chipset Mark+VT82C686B
 VGA Controller Integrated on Mark, 32MB
frame buffer share system
memory
 Ethernet 10/100Mb or
10/100/1000Mb LAN
optional, RJ-45 x 2,
Realtek 8100C/8110S
Option
 Audio(Daughter Board) AC97 Codec, MIC-in/
Line-in/ Line-out/ CD-in
 BIOS Award Plug & Play ISA
BIOS – 4Mb ROM

Half-size CPU Card HSB-668I
Chapter1GeneralInformation1-5
 IDE Interface 2 x ATA-100 channel
(Support four ATAPI
devices)
 Expansion Interface ISA Interface/PC-104
 Watchdog Timer 1~255 Sec. can be set with
software
 RTC InternalRTC
 Power Requirement +5V Only
 Operating Temperature 32°F~140°F (0°C ~ 60°C)
 EMC CE/FCCClassA
I/O
 Floppy Drive Interface 1 x Standard Floppy Disk
Drive port, supports up to
one Floppy Device
 Serial Port 4x COM ports: (Internal
Pin Header)
COM 1: RS-232
COM 2: RS-232/422/485
(Pin9 Supports +5V by
Jumper)
COM3: RS-232
COM4: RS-232
 Parallel Port 1x Parallel Port supports
SPP/EPP/ ECP mode
 Keyboard and Mouse 1 x Mini-DIN PS/2 K/B and

Half-size CPU Card HSB-668I
Chapter 1 General Information 1- 6
Mouse connector
1 x internal keyboard pin
header
 Universal Serial Bus One USB 1.1 Port
One 5x2 pin header for
Internal
 SSD DOC2000 support
 IR Interface Supports one IrDA and
CIR header

Half-size CPU Card HSB-668I
Chapter2QuickInstallationGuide2-1
Quick
Installation
Chapter
2
Guide
Notice:
The Quick Installation Guide is derive
d
f
rom Chapter 2 of user manual. For othe
r
chapters and further installation
instructions, please refer to the use
r
manual CD-ROM that came with th
e
p
roduct.
Part No. 2007668I11 Printed in Taiwan April 2008

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2-2
2.1 Safety Precaution
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2 - 3
2.2 Location of Connectors and Jumpers
Component Side
Solder Side

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2-4
2.3 Mechanical Drawing
Component Side
Solder Side

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2 - 5
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Jumpers
Label Function
JP1 COM2 Pin 9 Function Selection
JP2 Clear CMOS
JP3 LCD Voltage Selection

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2-6
2.5 List of Connectors
The board has a number of connectors that allow you to configure
your system to suit your application. The table below shows the
function of each board's connectors:
Label Function
FP1 Front Panel Connector 1
FP2 Front Panel Connector 2
PWR1 5V Connector
VGA1 VGA Display Connector
FDD1 Floppy Connector
IDE1~2 EIDE Connector
COM1 RS-232 Serial Port Connector
COM2 RS-232/422/485 Serial Port Connector
COM3 RS-232 Serial Port Connector
COM4 RS-232 Serial Port Connector
IR1 IrDA Connector
LPT1 LPT Port Connector
USB1 USB Connector
USB2 USB Connector
LAN1 10/100 or 100/1000 Base-TX Ethernet
Connector
LAN2 10/100 or 100 Base-TX Ethernet Connector
DIMM1 DIMM Slot
FAN1 Fan Connector
CN1 AC97 Connector
CN2 ATX Power Control Connector
CN3 LAN 1 Active LED Connector
CN4 LAN 2 Active LED Connector

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2 - 7
CN5 TTL 18/24BIT Channel Connector
CN6 TTL 36BIT Channel Connector
CN7 LVDS Channel Connector
CN8 PS2 Keyboard/Mouse Connector
CN9 Internal Keyboard Connector
DOC 1 Disk on Chip Socket

Half-size CPU Card HSB-668I
Chapter 2 Quick Installation Guide 2-8
2.6 Setting Jumpers
You configure your card to match the needs of your application by
setting jumpers. A jumper is the simplest kind of electric switch. It
consists of two metal pins and a small metal clip (often protected by
a plastic cover) that slides over the pins to connect them. To “close”
a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will
have three pins, labeled 1, 2 and 3. In this case you would connect
either pins 1 and 2 or 2 and 3.
123
Open Closed Closed 2-3
A pair of needle-nose pliers may be helpful when working with
jumpers.
If you have any doubts about the best hardware configuration for
your application, contact your local distributor or sales
representative before you make any change.
Generally, you simply need a standard cable to make most
connections.