Aaeon PCM-3336 User manual

PCM-3336
386SX-40
PC/104 CPU Card
With LCD & DiskOnChip
PCM-3336 Rev. A Manual
Part No. 2007333603 Printed in Taiwan September 2003

PC/104 CPU Card PCM-3336
i
Copyright Notice
This document is copyrighted, 2003. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material inthis document is for product information only and
is subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.

PC/104 CPU Card PCM-3336
ii
Acknowledgments
All other products’name or trademarks are properties of their respective
owners.
lITE is a trademark of Integrated Technology Express, Inc.
lIBM, PC/AT, PS/2, and VGA are trademarks of International Business
Machines Corporation.
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
•1 PCM-3336 PC/104 CPU Card
•1 Manual
•1Jumper Cap
•1 8-pin (4 x 2 pin header) for KB & PS/2 mouse
•1 FDD Cable
•1IDE Cable
•1SVGA Adapter
•1Parallel Port Adapter
•2Serial Port Adapter
If any of these items should be missing or damaged, please contact your
distributor or sales representative immediately.

PC/104 CPU Card PCM-3336
iii
Contents
Chapter 1 General Information
1.1Introduction ............................................................................1-2
1.2Features...................................................................................1-3
1.3Specifications...........................................................................1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions...................................................................2-2
2.2 Board Layout...........................................................................2-3
2.3Board Dimension....................................................................2-4
2.4List of Jumpers........................................................................2-5
2.5 List of Connectors...................................................................2-6
2.6 Setting Jumpers .......................................................................2-7
2.7HDD LED (J1).......................................................................2-8
2.8Reset Switch (J2).....................................................................2-8
2.9DiskOnChip (DOC) 2000 Installation (J3).............................2-8
2.10 LCD Power Select (J4)..........................................................2-9
2.11 Clear CMOS (J7) ...................................................................2-9
2.12 Shift Clock Select (J8)............................................................2-9
2.13 RS-232/422/485 COM2 Setting (J5 & J6)............................2-10
2.14 IDE Hard Drive Connector (CN1)......................................2-10
2.15 Keyboard Connector (CN2) .................................................2-11
2.16 Display Connector (CN4 & CN6) ........................................2-11
2.17 Power Supply Connector (CN5)...........................................2-12

PC/104 CPU Card PCM-3336
iv
2.18 Parallel Port (CN8)................................................................2-13
2.19 Serial Port (CN9 & CN11)....................................................2-14
2.20 Floppy Drive Connector (CN10)..........................................2-15
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization.................................................3-2
3.2 AMI BIOS Setup.....................................................................3-3
3.3Standard CMOS Setup............................................................3-5
3.4Advanced CMOS Setup ..........................................................3-6
3.5Advanced Chipset Setup.........................................................3-7
3.6PCI/Plug and Play Setup ........................................................3-8
3.7Peripheral Setup ......................................................................3-9

PC/104 CPU Card PCM-3336
Chapter 1 General Information
1-1
General
Information
Chapter
1

PC/104 CPU Card PCM-3336
Chapter 1 General Information 1 -
2
1.1 Introduction
The PCM-3336 comes equipped with an embedded
microcontroller ALi M6117C which is Intel386SX-40
compatible. In addition, it comes with two serial
ports(RS-232), one bi-directional printer port supporting SPP,
ECP and EPP modes, and IDE HDD interface and a floppy
disk controller. With its industrial grade reliability, the
PCM-3336 can operate continuously at temperature up to 140
℉(60℃).
The PCM-3336 is specially designed as a compact all-in-one
CPU card which incorporates a PC/104 connector into its
design, making non-passive backplane SBC applications
possible. The numerous features provide an ideal
price/performance solution for high-end commercial and
industrial applications where stability and reliability are
essential.
The PCM-3336 features an SVGA interface which supports
CRT and Flat Panel(TFT, STN and Mono displays), with
512KB onboard display memory.

PC/104 CPU Card PCM-3336
Chapter 1 General Information 1 -
3
1.2Features
nOnboard ALi M6117C, Intel 386SX-40 compatible CPU
nOnboard 8Mbytes EDO DRAM
nC&T 65545 LCD controller with 512KB display memory

PC/104 CPU Card PCM-3336
Chapter 1 General Information 1 -
4
1.3Specifications
System
lCPU ALi M6117C, Intel 80386SX-40 compatible
lChipset ALi M6117C
lIO Chipset ITE-8661
lBIOS AMI 128KB Flash BIOS.
lSystem Memory Onboard 8MB EDO DRAM
lEnhanced IDE
Interface Supports up to two IDE devices.
lFDD Interface Supports up to two floppy disk drives, 5.25"
(360KB and 1.2MB) and /or 3.5" (720KB, 1.44MB
and 2.88MB)
lSerial Ports One RS-232 and one RS-232.422/485 serial port.
Ports can be configured as COM1, COM2,
COM3, COM4, or disabled individually (16C550
equivalent)
lParallel port One bi-directional parallel port. Supports SPP,
ECP, and EPP modes.
lKeyboard/ PS2
Mouse connector
8-pin(4x2, pin header) connector supports PC/AT
keyboard and PS/2 mouse
lWatchdog Timer Can generate a system reset, IRQ15 or NMI.
Software selectable time-out interval
(30.5us~512sec, 30.5us/step)

PC/104 CPU Card PCM-3336
Chapter 1 General Information 1 -
5
lSSD Support DiskOnChip up to 1GB
lDMA 7 DMA channels (8237 equivalent)
lInterrupt 15 interrupt levels (8259 equivalent)
Display
lChipset C&T 65545
lDisplay Memory 512KB
lDisplay Type Supports non-interlaced CRT and LCD
(TFT, DSTN and Mono).
lResolution Up to 800 x 600 @ 256 colors
Expansion Interface
lPC/104 One 16-bit 104pin connector onboard for
PC/104 module expansion
Mechanical and Environment
lDimension 3.77”(L) x 3.54”(W)
lWeight 0.61b (0.25kg)
lOperating
Temperature 0~60℃(32~140℉)
lPower Supply
Voltage +5V(4.75V to 5.25V)

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
1
Quick
Installation
Guide
Chapter
2

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
2
2.1 Safety Precautions
Always completely disconnect the power cord from
your board whenever you are working on it. Do not
make connections while the power is on, because a
sudden rush of power can damage sensitive
electronic components.
Always ground yourself to remove any static charge
before touching the board. Modern electronic
devices are very sensitive to static electric charges.
Use a grounding wrist strap at all times. Place all
electronic components on a static-dissipative
surface or in a static-shielded bag when they are
not in the chassis

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
3
2.2Board Layout
CN6
J4
J8
CN4
U4
CN8
CN9
BT1
CN1
J3
CN2 J1
J2
U3
U8
CN3
CN7
CN5
CN10
CN11
J5
J6
J7
U17

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
4
2.3 Board Dimension

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
5
2.4List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Jumpers
Label Function
J1HDD LED
J2 Reset Switch
J3 DOCAddressSetting
J4 LCD Power Select
J5 COM2 RS-232/422/485 select
J6 COM2 RS-232/422/485 select for Data In
J7 Clear CMOS
J8 Shift Clock Select

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
6
2.5List of Connectors
The board has a number of connectors that allow you to configure
your system to suit your application. The table below shows the
function of each of the board's connectors:
Connectors
Label Function
CN1 HDD Connector
CN2KB/PS2Connector
CN3PC/104Connector
CN4SVGA Connector
CN5Power Connector
CN6LCDConnector
CN7PC/104Connector
CN8Printer Connector
CN9 COM1 Connector
CN10 Floppy Disk Connector
CN11 COM2 Connector

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
7
2.6Setting Jumpers
You configure your card to match the needs of your application by
setting jumpers. A jumper is the simplest kind of electric switch. It
consists of two metal pins and a small metal clip (often protected by
a plastic cover) that slides over the pins to connect them. To “close”
a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will
have three pins, labeled 1, 2 and 3. In this case you would connect
either pins 1 and 2 or 2 and 3.
12
3
Open Closed Closed 2-3
A pair of needle-nose pliers may be helpful when working with
jumpers.
If you have any doubts about the best hardware configuration for
your application, contact your local distributor or sales representative
before you make any change.
Generally, you simply need a standard cable to make most
connections.

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
8
2.7HDD LED (J1)
You can connect a LED to indicate that an IDE device is in use.
J1 Function
1-R/WIDE (LED Cathode)
2Pull high(LED Anode)
2.8Reset Switch (J2)
You can connect an external switch to easily reset your computer.
This switch restarts your computer as if you had turned off the
power then turned it back on.
J2 Function
1Reset
2GND
2.9DiskOnChip (DOC) 2000 Installation (J3)
1-23-45-6DOC Address
Off Off On D000
Off On Off D400
Off On On D800
On Off Off DC00
Off Off Off Disable

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -
9
2.10 LCD Power Select (J4)
You can use J4 jumper to select the voltage setting for the LCD
power. To select a certain voltage level close the corresponding pin
numbers with a pin cap. Pin 1-2 will provide +5V of power and pin
2-3 will provide +3.3V of power.
J4 Function
2-3+3.3V
1-2+5V (Default)
2.11 Clear CMOS (J7)
Warning:
To avoid damaging the computer, always turn off the power supply before setting
“Clear CMOS.” Before turning on the power supply, set the jumper back to
“Normal.”
J7 Function
1-2Clear CMOS
2-3Normal (Default)
2.12 Shift Clock Select (J8)
J8 Function
2-3Ashclk
1-2Shclk

PC/104 CPU Card PCM-3336
Chapter 2 Quick Installation Guide 2 -10
2.13 RS-232/422/485 COM2 Setting (J5 & J6)
J5 J6 Function
1-2, 4-5,7-8, 10-11 1-2RS-232 (Default)
2-3, 5-6,8-9, 11-12 3-4RS-422
2-3, 5-6,8-9, 11-12 5-6RS-485
2.14 IDE Hard Drive Connector (CN1)
Pin Signal Pin Signal
1Reset 2GND
3HD7 4HD8
5HD6 6HD9
7HD5 8HD10
9HD4 10 HD11
11 HD3 12 HD12
13 HD2 14 HD13
15 HD1 16 HD14
17 HD0 18 HD15
19 GND 20 NC
21 NC 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IORDY 28 BALE
29 VCC 30 GND
31 IRQ14 32 -I/O 16
33 SA1 34 NC
35 SA0 36 SA2
37 HDCS0 38 HDCS1
39 -ACT 40 GND
41 VCC 42 VCC
43 GND 44 NC