Aaeon PCM-8200 User manual

Compact Board PCM-8200
PCM-8200
Intel® Pentium® M and
Celeron® M processors
Compact Board
With LVDS LCD, TV-Out,
Ethernet, Audio, CompactFlash TM,
USB, 4 COMs & Mini PCI
PCM-8200 Rev. A Manual 1
st Ed.
Apr. 2004

Compact Board PCM-8200
i
Copyright Notice
This document is copyrighted, 2004. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any in-
fringements upon the rights of third parties that may result from its use.
The material inthis document is for product information only and is
subject to change without notice. While reasonable efforts have been
made in the preparation of this document to assure its accuracy, AAEON
assumes no liabilities resulting from errors or omissions in this document,
or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design without
notice to its users.

Compact Board PCM-8200
ii
Acknowledgments
All other product s’name or trademarks are properties of their respective owners.
lAward is a trademark of Award Software International, Inc.
lCompactFlash™is a trademark of the Compact Flash Association.
lIntel® ,Pentium®4, and Celeron® are trademarks of Intel® Corporation.
lMicrosoft Windows®is a registered trademark of Microsoft Corp.
lITE is a trademark of Integrated Technology Express, Inc.
lIBM, PC/AT, PS/2, and VGA are trademarks of International Business
Machines Corporation.
lSoundBlaster is a trademark of Creative Labs, Inc.

Compact Board PCM-8200
iii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
•1 CPU Card
•1 Quick Installation Guide
•1 CD-ROM for manual (in PDF format) and drivers
•1 Jumper cap
If any of these items should be missing or damaged, please contact your
distributor or sales representative immediately.

Compact Board PCM-8200
iv
Contents
Chapter 1 General Information
1.1Introduction ...................................................................................1-2
1.2Features ..........................................................................................1-4
1.3Specifications .................................................................................1-5
Chapter 2 Quick Installation Guide
2.1 Safety Precautions .........................................................................2-2
2.2 Location of Connectors and Jumpers .........................................2-3
2.3 Mechanical Drawing......................................................................2-5
2.4 List of Jumpers ..............................................................................2-7
2.5 List of Connectors .........................................................................2-8
2.6 Setting Jumpers..............................................................................2-10
2.7 LCD Voltage Selection (JP2) .......................................................2-11
2.8 Audio Out Selection (JP3)............................................................2-11
2.9 Clear CMOS (JP4).........................................................................2-11
2.10 COM2 RS-232/422/485 Selection (JP5, JP6 & JP7)..............2-11
2.11 COM2 Ring/+5V/+12V Selection (JP8).................................2-12
2.12 Channel2 LVDS Connector (CN1)...........................................2-12
2.13 VGA Display Connector (CN2) ................................................2-13
2.14 Front Panel Connector (CN3)...................................................2-13
2.15 FAN Connector (CN4)...............................................................2-13
2.16 Channel1 LVDS Connector (CN5)...........................................2-14
2.17 ATX Power Connector (CN6) ..................................................2-14

Compact Board PCM-8200
v
2.18 LAN LED Connector (CN7) ....................................................2-15
2.19 Option PME Connector (CN8).................................................2-15
2.20 Audio Connector (CN9).............................................................2-15
2.21 TV_Out Connector (CN10) ......................................................2-16
2.22 DVI Connector (CN11) .............................................................2-16
2.23 Audio 5.1 Channel/SPDIF Connector (CN12).......................2-17
2.24 USB Connector (CN13 & CN14).............................................2-17
2.25 LPT Port Connector (CN15).....................................................2-18
2.26 FAN Connector (CN16)............................................................2-18
2.27 IrDA Connector (CN17) ............................................................2-19
2.28 Digital I/O-2Connector (CN18) ..............................................2-19
2.29 Keyboard/Mouse Connector (CN19) ......................................2-20
2.30 RS-232/422/485 Serial Port Connector (CN20).....................2-21
2.31 Digital I/O-1 Connector (CN21) ..............................................2-22
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization. .....................................................3-2
3.2 Award BIOS Setup........................................................................3-3
3.3 Standard CMOS Features .............................................................3-6
3.4 Advanced BIOS Features .............................................................3-7
3.5 Advanced Chipset Features ..........................................................3-8
3.6 Integrated Peripherals ...................................................................3-9
3.7 Power management Setup............................................................3-10
3.8 PnP/PCI configuration ................................................................3-11
3.9 PC Health Status............................................................................3-12
3.10 Frequency/Voltage Control .......................................................3-13

Compact Board PCM-8200
vi
3.11 Load Fail-Safe Defaults ..............................................................3-14
3.12 Load Optimized Defaults...........................................................3-15
3.13 Set Supervisor/User Password ..................................................3-16
3.14 Save &Exit Setup........................................................................3-17
3.15 Exit without Saving .....................................................................3-18
Chapter 4 Driver Installation
4.1 Installation......................................................................................4-3
Appendix A I/O Information
A.1 I/O Address Map .................................................................... A-2
A.2 1st MB Memory Address Map ................................................ A-2
A.3 IRQ Mapping Chart ................................................................ A-3
A.4 DMA Channel Assignments .................................................. A-3
Appendix B Programming the Watchdog Timer
B.1 Programming.............................................................................B-2
B.2 IT8712 Watchdog Timer Initial Program ..............................B-6

Compact Board PCM-8200
Chapter 1 General Information 1-1
General
Information
Chapter
1

Compact Board PCM-8200
Chapter 1 General Information
1
-
2
1.1 Introduction
PCM-8200 series are powered by the IntelPentiumM processor with
the Intel® 855GME chipset and new Intel6300ESB I/O Controller
South Bridge integrated.PCM-8200 is delicately designed for
working-efficiency with low power consumption and simple voltage input
required application.(5V only workable)
Outstanding Power Efficiency
The PCM-8200 supports IntelPentiumM / CeleronM processorsup
to 1.60GHz with 400MHz FSB. System memory holds up to 1GB with fast
DDR 333MHz providing high calculate and graphic ability but with extreme
low power consumption.This feature is especially suitable for Video,
Automation controller, Multimedia application.
Besides the excellent CPU performance, PCM-8200 also provides multiple
display functions, it allows user to display different content on CRT/LCD,
CRT/DVI,CRT/TV,LCD/DVI or LCD/TVthis feature opens a shortcut
to multi-display demander with cheaper solution. PCM-8200 does really the
most power efficiency board that you can find at this moment.
Maximum Expansion Interface
PCM-8200 provides interface capabilities of two ports serial ATA controller;
USB 2.0 host controller support up to 4 USB ports (Support Embedded
USB DOM); four serial I/O ports support and Watchdog Timer support. In
addition, the excellent 48/24/18-bit LVDS supports high quality

Compact Board PCM-8200
Chapter 1 General Information
1
-
3
LCD display resolution. The TV-out (NTSC & PAL) function extendsthe
display options to CRT, LCD, TV and etc. One Type III mini PCI socket
can be used for wireless LAN interface. And onboard Intel82541
Ethernet controller stands for fast 1 Gigabyte transferring speed. All
featured expansion interfaces have been enhanced in this 8” x 5.75”
computer board.
The PCM-8200 is the ideal choice for dust/temperature-sensitive high end
Industrial Automation application. For space-constrained environments
such automobile, PCM-8200 is also a perfect fit.Even is great for KIOSK
and POS implementations with low power consumption and pleasant
multimedia presentations.

Compact Board PCM-8200
Chapter 1 General Information
1
-
4
1.2Features
•Supports Socket 478-based Intel® Pentium® M and
Celeron® M processors
Or onboard Low Voltage Intel® Pentium M processor
•Supports 48-bit Dual channel LVDS TFT panels
•AC-97 3D surround 5.1 channel Audio
•Supports Type II CompactFlash Memory
•Supports Type III Mini PCI and PCI slots
•4 USB 2.0 / Mini PCI / Digital I/O / TV-Out / SATA

Compact Board PCM-8200
Chapter 1 General Information
1
-
5
1.3 Specifications
System
lCPU: Socket 478-based Intel®Pentium®
M and Celeron M®processor (0.13
μ) up to 1.6GHz with FSB
400 MHz, or onboard Low Voltage
Intel®Pentium®M
processor up to 1.1GHz
lSystem: 184-pin DDR SDRAM DIMM x 1,
Max. 1GB (PC-266/333)
lChipset: Intel®855GME + 6300ESB
lI/O Chipset: ITE IT8712F
lBIOS: Award 512 KB FLASH ROM
lEthernet:Intel®82551ER/82541GI
(Optional),
10/100/1000Base-T RJ-45
connector x 1
lSSD:Type II CompactFlash slot
lWatchdog Timer:Generate a system reset
lExpansion Interface: Type IIIMini PCI x 1, PCI slot x 1
lBattery: Lithium battery
lH/W Status Monitoring:
Supports power voltages, fan speed
and temperature

Compact Board PCM-8200
Chapter 1 General Information
1
-
6
monitoring
lPower Supply Voltage: ATX, 5 voltage only
lBoard size: 8" (L) x 5.75" (W)
(203mm x 146mm)
lGross Weight: 1.2lb(0.5Kg)
Display
lChipset Intel®855GME + Chrontel 7009
lMemory Size: Shared memory up to 64MB with
Dynamic Video Memory
Technology
lResolution: Up to 1280 X 1024 @ 32bpp
colors for CRT; Up to 1280 X 1024
@ 24bpp colors for LCD
lSupports CRT/LCD,CRT/DVI, CRT/TV, LCD/DVI and
LCD/TV simultaneous display
lSupports CRT/LCD,CRT/DVI, CRT/TV, LCD/DVI and
LCD/TV dual view
lSupports screen image rotation
I/O
lMIO: EIDE (UDMA 100) x 1, Serial ATA
x 2, FDD x 1, KB + Mouse x 1,
RS-232 x 3, RS-232/422/485 x 1,
Parallel x 1, CRTx1

Compact Board PCM-8200
Chapter 1 General Information
1
-
7
lIrDA:One IrDA Tx/Rx header
lAudio:Mic in, Line in, Line out / Speaker
Out. 5.1 output.
lUSB: One 5 x 2 and one 9 x 2-1pin
headers
support 4 USB 2.0 ports (One for
Embedded USB DOM)
lDigital I/O: Supports 8 in & 8 out, 16 in or 16
out

Compact Board PCM-8200
Chapter 2 Quick InstallationGuide 2 -1
Quick
Installation
Guide
Chapter
2
Part No. 2007820010 Printed in Taiwan Apr.2004
Notice:
The Quick Installation Guide is derived
from
Chapter 2 of user manual. For other
chapters and
further installation
instructions, please refer to the
user
manual CD-ROM that ca
me with the
product.

Compact Board PCM-8200
Chapter 2 Quick Installation Guide
2
-
2
2.1 Safety Precautions
Always completely disconnect the power cord from
your board whenever you are working on it. Do not
make connections while the power is on, because a
sudden rush of power can damage sensitive
electronic components.
Always ground yourself to remove any static charge
before touching the board. Modern electronic
devices are very sensitive to static electric charges.
Use a grounding wrist strap at all times. Place all
electronic components on a static-dissipative
surface or in astatic-shielded bag when they are not
in the chassis

Compact Board PCM-8200
Chapter 2 Quick Installation Guide
2
-
3
2.2Location of Connectors and Jumpers
Component Side

Compact Board PCM-8200
Chapter 2 Quick Installation Guide
2
-
4
Solder Side

Compact Board PCM-8200
Chapter 2 Quick Installation Guide
2
-
5
2.3 Mechanical Drawing
Component Side

Compact Board PCM-8200
Chapter 2 Quick Installation Guide
2
-
6
Solder Side