Aaeon ACP-1073 User manual

Multi-Touch Panel PC ACP- 1 073
ACP-1073
7" WSVGA Ultra-slim
Fanless Multi-Touch Panel PC
Intel®AtomTM N2600 Processor
RS-232, RS-232/422/485
USB2.0, Mini HDMI
ACP-1073 Manual 5thEd
December 8, 2014

Multi-Touch Panel PC ACP- 1 073
Copyright Notice
This document is copyrighted, 2014. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties, which may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON, assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i

Multi-Touch Panel PC ACP- 1 073
Acknowledgments
Intel®, AtomTM are registered trademarks of Intel®Corporation.
Microsoft®Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
All other product names or trademarks are properties of their
respective owners.
ii

Multi-Touch Panel PC ACP- 1 073
Packing List
Before you begin installing your Panel PC, please make sure
that the following items have been shipped:
ACP-1073 Fanless Multi-Touch Panel PC
RJ-48Type COM Port Cable x 3
Power Adapter x 1
Product DVD
Contains User’s Manual (in PDF format), Drivers and
Utilities
If any of these items are missing or damaged, you should contact your
distributor or sales representative immediately.
iii

Multi-Touch Panel PC ACP- 1 073
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
service personnel should open the equipment.
iv

Multi-Touch Panel PC ACP- 1 073
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to
work according to the user’s manual.
e. The equipment has been dropped and damaged.
f.The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 70° C (158° F). IT MAY
DAMAGE THE EQUIPMENT.
16. External equipment intended for connection to signal input/output
or other connectors, shall comply with relevant UL / IEC standard
(e.g. UL 1950 for IT equipment and UL 60601-1 / IEC 60601 series
for systems – shall comply with the standard IEC 60601-1-1,
Safety requirements for medical electrical systems. Equipment
not complying with UL 60601-1 shall be kept outside the patient
environment, as defined in the standard.
17. When the temperature of CPU is higher than 35°C, the frequency
of CPU will be adjusted automatically. For example, if the
temperature of Intel Core i7 is 40°C, the frequency of the CPU will
be between 1.8~1.3 GHz.
18. As most electronic components are sensitive to static electrical
charge, be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
v

Multi-Touch Panel PC ACP- 1 073
and contain all electronic components in any static-shielded
devices.
Caution:
It may cause the danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type
recommended by the manufacturer.
vi

Multi-Touch Panel PC ACP- 1 073
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX1
3. Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
vii

Multi-Touch Panel PC ACP- 1 073
FCC
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received
including interference that may cause
undesired operation.
viii

Multi-Touch Panel PC ACP- 1 073
Safety Symbol Description
The following safety symbols are further explanations for your
reference.
Attention, consult ACCOMPANYING
DOCUMENTS.
Ground wire
Protective Ground wire.
ix

Multi-Touch Panel PC ACP- 1 073
China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Panel PC/ Workstation
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
及其电子组件
×
○
○
○
○
○
外部信号
连接器及线材
×
○
○
○
○
○
外壳
×
○
○
○
○
○
中央处理器
与内存
×
○
○
○
○
○
硬盘
×
○
○
○
○
○
液晶模块
×
○
○
○
○
○
光驱
×
○
○
○
○
○
触控模块
×
○
○
○
○
○
电源
×
○
○
○
○
○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006
标准规定的限量要求以下。
X
：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006
标准规定的限量要求。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质中央处理器、内存、硬盘、光驱、触控模块为选购品。
x

Multi-Touch Panel PC ACP- 1 073
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features .................................................................... 1-3
1.3 Specification.............................................................. 1-4
1.4 General Information................................................... 1-7
Chapter 2 Hardware Installation
2.1 Safety Precautions ....................................................2-2
2.2 Connectors and Jumpers of The Main Board ........... 2-3
2.3 List of Jumpers..........................................................2-4
2.4 List of Connectors ..................................................... 2-5
2.5 Clear CMOS Jumper (JP2) ....................................... 2-6
2.6 LVDS Port 1 Backlight Inverter VCC Selection (JP3)2-6
2.7 LVDS Port 1 Operating VDD Selection (JP5) ........... 2-6
2.8 AT/ATX Power Supply Mode Selection (JP6)........... 2-7
2.9 Realtek LAN (RJ-45) Port (CN12).............................2-7
2.10 COM1,RJ-45 Port (CN20).......................................2-8
2.11 COM2,COM3 RS232/422/485 ,RJ-45 Port
(CN21,CN22)................................................................... 2-9
2.12 Buzzer (CN8)........................................................... 2-11
2.13 RESET (CN9)..........................................................2-11
2.14 LPC Debug Port (CN10) ......................................... 2-11
2.15 USB 2.0 Port 5 (CN11)............................................ 2-12
xi

Multi-Touch Panel PC ACP- 1 073
2.16 USB 2.0 Port 4 (CN27)............................................ 2-13
2.17 18-bits LVDS Output (CN15)................................... 2-13
2.18 HDMI Type C (CN17)..............................................2-14
2.19 Inverter / Backlight Connector (CN18)....................2-15
2.20 DDR3 SODIMM Slot (DIMM1) ................................2-16
2.21 Mini Card Slot (mSATA function only)..................... 2-16
2.22 Mechanical Drawing of the ACP-1073....................2-19
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization . ................................. 3-2
3.2 AMI BIOS Setup........................................................3-3
Chapter 4 Driver Installation
4.1 Installation ................................................................. 4-3
Appendix A Programming the Watchdog Timer
A.1 Watchdog Timer Registers ....................................A-2
A.2 Watchdog Sample Program...................................A-3
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
B.2 Memory Address Map............................................B-3
B.3 IRQ Mapping Chart ..............................................B-4
B.4 DMA Channel Assignments...................................B-7
Appendix C Miscellanea
C.1 General Cleaning Tips.......................................... C-2
C.2 Cleaning Tools...................................................... C-3
xii

Multi-Touch Panel PC ACP- 1 073
C.3 Scrap Computer Recycling ................................. C-5
Appendix D AHCI Setting
D.1 Setting AHCI......................................................... D-2
xiii

Multi-Touch Panel PC ACP- 1 073
General
Information
Chapter
1
Chapter 1 General Information 1-1

Multi-Touch Panel PC ACP- 1 073
1.1 Introduction
The ACP-1073 is a Multi-Touch Industrial Panel PC with onboard
Intel®Atom™ N2600 processor-based computer. It is a PC-based
system with 7” true color TFT LCD display, integrated multimedia
functions make them the perfect platforms to build comprehensive
lifestyle computing applications.
The ACP-1073 includes all the features of a powerful computer into
a slim and attractive mechanism design. The ACP-1073 adopts 250
nits TFT display with 1024 x 600 resolution. This model supports
two-point Multi-Touch function (Window 7 : Two finger, Win XP :
Single finger, Window embedded version : Single Finger.) and full
flat design is easy to clean. Moreover, its front bezel is
IP65/NEMA4 for auxiliary water-proof protection. In addition, the
ACP-1073 deploys 7H hardness Anti-Scratch Surface to avoid
accidental damage.
The ACP-1073 supports one mSATA Hard Disk Drive for the
storage function, and has optional wireless function with WiFi
module by USB interface. Moreover, this model has one RS-232
and two RS-232/422/485 RJ-48 connectors, four USB2.0 ports, and
one Mini HDMI. It is ideal for versatile applications.
Chapter 1 General Information 1-2

Multi-Touch Panel PC ACP- 1 073
1.2 Features
7” WSVGA (1024 x 600) TFT LCD Display
Aluminum Design
7H Two-point Multi-Touch Display
Intel®Atom™ N2600 Processor
Fanless System
VESA75 / Stand
Chapter 1 General Information 1-3

Multi-Touch Panel PC ACP- 1 073
1.3 Specification
System
Processor Onboard Intel®Atom™N2600 Processor
System Memory DDR3 SODIMM x 1, Max. 2 GB
(Default is
2G RAM)
LCD / CRT Controller Integrated graphics in Intel®NM10
I/O Port RS-232 x 1 (RJ-48 connector)
RS-232/422/485 x 2 (RJ-48 connector)
LAN x 1 (RJ-45 connector)
USB2.0 x 4
Mini HDMI x 1
Power button x 1
Lockable power connector x 1
Storage Disk Drive Half-size mSATA Hard Disk Drive bay x 1
Expansion WiFi module by USB interface x 1
OS Support Windows®XP 32-bit, Windows®7 32-bit,
Linux Kernal 2.6.3 or higher
Note : Suggest to use AAEON Pre-installed SSD storage.
Mechanical
Construction IP-65/ NEMA4 for front bezel
Mounting VESA 75
Dimension 7.96”(W) x 5.28”(H) x 1.46”(D) (202.19mm
x 134.18mm x 37.2mm)
Chapter 1 General Information 1-4

Multi-Touch Panel PC ACP- 1 073
Carton Dimension 13.58” x 7.87” x 9.65’’ (345mm x 200mm
x
245mm)
Net Weight 2.42 lb (1.1 kg)
Gross Weight 5.5 lb (2.5 kg)
Environmental
Operating Temperature 32oF~113oF (0oC~45oC) without airflow
32oF~122oF (0oC~50oC) with airflow
Storage Temperature -4oF~158oF (-20oC~70oC)
Storage Humidity 95% @ 40oC, non-condensing
Vibration 1 g rms/ 5-500Hz/ Random Operation
(HDD)
Shock 15G peak acceleration (11 msec. duration)
(HDD)
EMC CE/FCC Class A
Power Supply
DC Input DC 12V, with AC power adapter with lock
LCD
Display Type 7” TFT-LCD, LED
Max. Resolution 1024 x 600
Max. Colors 26 M colors (6/8-bit for R, G, B)
Luminance (cd/m2)250 cd/m2
Contrast Ratio 700:1
Viewing Angle 150º (H), 145º (V)
Chapter 1 General Information 1-5

Multi-Touch Panel PC ACP- 1 073
Backlight MTBF (Hours) 50,000
Touchscreen
Type Projected Capacitive Multi-Touch (Two
points)
Resolution 2048x2048
Light Transmission 90%
Chapter 1 General Information 1-6