ABB i-bus 6115-24-500 User manual

73 - 1 - 5824
22013
ABB i-bus®EIB
UP switching sensor
6115-/16-/17- 24 - 500
for UP bus coupling unit 6120 U-500
Operating instructions
only for authorized, skilled electricians with
EIB training

Important instructions
Attention
It is absolutely essential that the EIB bus is installed by
anauthorizedelectrician.Layingandconnectionofbus
line and applications devices must be effected in
conformity with valid regulations according to DIN -
VDE and the EIB manual of the ZVEI/ZVEH.
Notes
The covering frame supplied with the UP switching sensor
(item no. 1721) is equipped with an inspection window (fig.
1, pos. 2). You may use perforated sheets for labelling
(item no. 1799).
The manufacturer database of ABB is continuously
supplemented and completed. It stores the latest types of
applications and their related descriptions. If this database
is not available to you, please send us for a copy.

Technical data / Fig. 1
Nominal voltage: 5 V
Current consumption: < 10 mA
Environmental temperature range: -5 to +45 °C
Fig. 1
6120 U
Phy. Adresse
6
78
1
2
3
4
5

Installation
Plug the application (Fig. 1, pos. 1) onto the UP bus coupling
unit (pos. 4) in such a way that the 10-pin connector (pos.
6) on the rear side is not canted or tilted. The plastic webs
(pos. 7) on the rear side of the application must be inserted
into the relieves (pos. 5) provided in the retaining ring of the
bus coupling unit.
Note
Operator function and addressing (see also operating
instructions for the UP bus coupling unit) may be
programmed simultaneously or at different times.
Dismounting
The application has got two relieves on its left and right
hand side (pos. 8) where it may be dismounted from the
bus coupling unit. Use these relieves, for otherwise only a
single key but not the whole application will be loosened.

Adapt bus coupling process
Assign physical address
• Connect a PC equipped with the EIBA software (ETS)
to the EIB bus line via an EIB-RS 232 interface.
• Press the programming key at the bus coupling unit:
the red programming LED will become illuminated.
• After the physical address has been programmed,
the red LED will go out.
• Write the number of the physical address on your
device using a smudge-proof pencil (cf. Fig. 1, pos. 3).
Assign group address(es)
• Group addresses are assigned via a PC in connection
with the ETS software.

Adapt bus coupling process
Select application
By default, the UP bus coupling unit is programmed to
operate one application for the switching (1-, 2-, 4-fold) of
consumers.
To a 4-fold switching sensor, for instance, the following
functions apply:
Key I 0
Function ON OFF
LED red green
Physical address F F F F
Group address 0/1 - 0/4
These functions apply analogously to the single or 2-fold
switching sensor.
Openthedevice windowandchoosethe desiredapplication
version. At present, there are two versions available.

Adapt bus coupling process
Differentiate application
Version 1
A separate group address may be assigned to the LED of
the rocker switch. This address is independent from the
group address which has been assigned to the switching
function of the rocker.
Example for application:
The LED shall indicate the current switching status of an
actuator which is selected via several group addresses.
Version 2
The group address of the rocker's switching function and
that of the integrated LED are indentical.
The LED will not change its colour, if a data telegram has
not been transmitted properly.

Adapt bus coupling process
Instructions
You may differentiate version 1 and 2 by means of the ETS
via the “parameters” option:
• LED colour
The colour of the LED in ON/OFF state may be set to
“red” or “green”.
• LED function
Assign a function to individual LED's or set them
without any function; this means that an LED which
has not been assigned any function will not change
its colour.
If a touch contact / dimmer function is requested, the UP
bus coupling unit has to be loaded with different ABB
application data (applications).