ABB SAS-W1.1E User guide

—
2CSM600727D09 01 | 01.03.2019
Busch-/ABB-secure@home
System Manual
Types of Central Unit
With GSM
SAS-W1.1E SAS-W1.11E
SAS-W1.1F SAS-W1.11F
Basic
SAS-W2.1E SAS-W2.11E
SAS-W2.1F SAS-W2.11F

BUS CH- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 2/56
Contents
1Introduction ................................................................................................................................5
1.1 Where to find the information ................................................................................................. 5
1.2 Conformity ................................................................................................................................... 5
1.3 Disclaimer..................................................................................................................................... 5
1.4 Trademarks and copyrights ..................................................................................................... 5
Use the system................................................................................................................................ 6
2Command interface ................................................................................................................... 6
2.1 Display ........................................................................................................................................... 6
2.1.1 Meaning of the icons................................................................................................ 6
2.1.2 Authentication ............................................................................................................7
2.1.3 Main user menu ..........................................................................................................7
2.1.4 Status of the individual zones................................................................................ 8
2.2 LEDs ............................................................................................................................................... 8
2.3 Keypad........................................................................................................................................... 9
2.4 Authentication............................................................................................................................. 9
2.4.1 User ID ......................................................................................................................... 9
2.4.2 Password..................................................................................................................... 9
2.5 Authorisation level...................................................................................................................... 9
3Arming and disarming the system.......................................................................................... 11
3.1 Arming or disarming using the keypad ................................................................................ 11
3.1.1 Rapid arming or disarming.................................................................................... 11
3.1.2 Global arming............................................................................................................ 11
3.1.3 Global disarming......................................................................................................12
3.1.4 Partial arming............................................................................................................12
3.1.5 Partial disarming......................................................................................................13
3.2 Arming or disarming using the remote control ..................................................................13
3.3 Arming using Forced Block......................................................................................................13
3.4 Reset .............................................................................................................................................14
4Panic and burglary ....................................................................................................................15
4.1 Activating the panic alarm.......................................................................................................15
4.1.1 Activation using the keypad ..................................................................................15
4.1.2 Activation using the remote control....................................................................15
4.2 Activate the burglar alarm .......................................................................................................15
4.2.1 Activation using a dedicated button...................................................................15
4.2.2 Activation using the remote control....................................................................15
5Alarms and event memories ....................................................................................................16
5.1 Alarm priority..............................................................................................................................16
5.2 How to block an alarm..............................................................................................................16
5.3 Events history............................................................................................................................. 17
5.3.1 View events................................................................................................................ 17
5.3.2 Interpreting a stored event.................................................................................... 17
6Remote commands.................................................................................................................. 20
6.1 Telephone commands with DTMF tones ............................................................................. 20
6.2 SMS Commands .........................................................................................................................21
7System status............................................................................................................................22
8Central unit settings.................................................................................................................23
8.1 Adjust display ............................................................................................................................ 23
8.2 Audio Settings........................................................................................................................... 23

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 3/56
8.2.1 Beep volume ............................................................................................................. 23
8.2.2 Sound Feedback ...................................................................................................... 24
8.2.3 Alarms........................................................................................................................ 24
8.3 Setting date and time.............................................................................................................. 25
8.4 Change PIN................................................................................................................................. 26
8.5 Operating method and change language ........................................................................... 26
8.6 Rapid arming customisation...................................................................................................27
Install and configure the system ................................................................................................. 29
9Main characteristics ................................................................................................................ 29
9.1 Main functions of the central unit......................................................................................... 29
9.2 System capacity ........................................................................................................................ 29
10 Designing a system ................................................................................................................. 30
10.1 Information on radio waves.................................................................................................... 30
10.2 Use the zones............................................................................................................................. 30
10.2.1 Zone types................................................................................................................ 30
10.2.2 Subdivision into zones............................................................................................31
11 Installing the central unit.........................................................................................................32
11.1 Workspaces ................................................................................................................................ 32
11.2 First start-up.............................................................................................................................. 32
11.2.1 Authentication ......................................................................................................... 32
11.3 General and alarm reports...................................................................................................... 34
12 Programming.............................................................................................................................35
12.1 System creation......................................................................................................................... 35
12.2 Programming zones and sensors ......................................................................................... 35
12.2.1 To programme a new zone:................................................................................... 35
12.2.2 To modify or delete a zone:................................................................................... 35
12.2.3 To programme a sensor: ....................................................................................... 36
12.3 Programming system devices ................................................................................................37
12.3.1 Remote Control Programming..............................................................................37
12.4 Programming external sirens..................................................................................................41
12.4.1 Possible parameters................................................................................................41
12.4.2 Zones Filters............................................................................................................. 42
12.4.3 Alarms........................................................................................................................ 42
12.4.4 Events ........................................................................................................................ 42
12.5 Repeater programming........................................................................................................... 43
12.5.1 Possible parameters............................................................................................... 43
12.6 Telephone contact programming ......................................................................................... 43
12.6.1 Customised message............................................................................................. 45
12.6.2 Phone message sending sequence..................................................................... 46
12.6.3 Receiving telephone calls from the central unit............................................... 46
12.7 Home automation free@home.............................................................................................. 46
12.7.1 Version....................................................................................................................... 46
12.7.2 Key .............................................................................................................................. 47
12.7.3 GTW Reset ................................................................................................................ 47
12.8 System test................................................................................................................................. 47
12.9 User management .................................................................................................................... 49
12.9.1 Change a user .......................................................................................................... 49
12.9.2 Deleting a user......................................................................................................... 49
13 Maintenance ..............................................................................................................................51
13.1 Power management ..................................................................................................................51
13.1.1 Battery........................................................................................................................51

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 4/56
13.1.2 Electrical power network........................................................................................51
13.2 Placing system in maintenance mode...................................................................................51
13.2.1 Replacing the central unit battery........................................................................51
13.2.2 SIM Replacement..................................................................................................... 52
13.2.3 Central unit reset..................................................................................................... 52
13.2.4 Adding devices ........................................................................................................ 52
13.2.5 Deleting devices ...................................................................................................... 52
13.2.6 Replacing devices.................................................................................................... 52
13.2.7 Central unit firmware update............................................................................... 53
14 Problem solving ....................................................................................................................... 54
15 Central unit technical specifications..................................................................................... 55
16 cyber security disclaimer........................................................................................................ 56
16.1 Network Manager ..................................................................................................................... 56

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 5/56
1INTRODUCTION
Thank you for purchasing the BUSCH-/ABB-secure@home central unit. This manual contains
all of the information that the user needs for day-to-day use of the central unit and the intru-
sion alarm system, including configuration and maintenance procedures.
1.1 Where to find the information
This manual contains all of the information to use, configure and maintain the central unit.
It also provides suggestions for planning a security system, includes a list of the technical
specifications of the central unit and sets out the procedures for isolating the system and re-
solving any faults. The configuration section is exclusively intended for use by the technician
who installs the system.
1.2 Conformity
The central unit has been designed and built according to quality and safety standards pro-
vided for in the regulations and laws in force. Conformity with qualitative requirements is
confirmed by the inclusion of the CE mark in accordance with regulation 1999/05/EC.
Warning! Installation must only be performed by a qualified electrician.
When installing the system, current national electrical regulations regarding the installation
site must be complied with. It should be noted that the conformity referred to above and the
performance of the product may be compromised by:
-incorrect electrical power supply;
-incorrect installation or incorrect, improper or otherwise inconsistent use of the in-
structions provided in the installation and use manual or in the instructions provided
with the devices;
-replacement of original parts or accessories with other types that have not been ap-
proved by the manufacturer, or performed by unauthorised personnel.
In the event of opting for non-conforming configurations, the product labels confirming con-
formity must be modified or removed.
1.3 Disclaimer
All the information in this document has been collected and checked with care. However, ABB
and BUSCH-JAEGER cannot be held liable for any printing errors or technical inaccuracies.
ABB and BUSCH-JAEGER reserve the right to improve or change the products described in
this manual at any time and without prior notice. This manual may also contain references or
information about products or services that are not yet on the market. The inclusion of such
references or information does not in any way imply that ABB and BUSCH-JAEGER intend to
market such products or services.
1.4 Trademarks and copyrights
All trademarks mentioned in the document belong to their respective owners.
© Copyright ABB S.p.A. 2018 - All rights reserved.
© Copyright BUSCH-JAEGER GmbH. 2018 - All rights reserved.

BUS C H- /AB B-S E CU R E @ HOM E
2 CSM 6 0 072 7 D0 9 01 6/56
USE THE SYSTEM
This section contains all of the information that the user needs for day-to-day use of the cen-
tral unit and the intrusion alarm system, including some configuration procedures.
2COMMAND INTERFACE
2.1 Display
The liquid crystal display screen shows all of the information relevant to the configuration of
the central unit and operation of the system. It may contain up to 8 lines of text with up to 20
characters each, or a series of icons, or a combination of text and icons.
The display is normally off, and lights up when a key is pressed.
When idle, the screen displays the following information:
-Status of the system (armed/disarmed/partial armed (Note1))
-2 icons to indicate, from left to right, the status of the central unit power supply and
the GSM connection.
Pressing the  key once will bring up detailed information on the status of the individual
zones, while pressing it a second time:
ocentral unit FW release number
ophysical address (8 digits) of the central unit
odate - time
oconnection to ABB-free@home
obattery level
Note 1:
Armed
All zones are armed using the same method
Disarmed
All zones are disarmed
Partially armed
Not all zones are armed or they are armed in a non-uniform manner
2.1.1 Meaning of the icons
Status of
Icon
Meaning
Telephone
The connection to the GSM telephone network is working. The
signal strength is displayed using the bars (1 to 3).
GSM telephone network not identified, SIM Card not installed,
not identified, expired or not active.
Intrusion alarm system
System disarmed.
System armed in "Notification" mode.
System Disarmed

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 7/56
Alarm armed in "Home mode”.
Alarm armed in "Away mode”.
24h active zone
Central unit power supply
Indicates the presence of 230V and battery power supply
Indicates the central unit battery charge status
(fully charged in the example)
Battery missing
2.1.2 Authentication
To perform the authentication process when the window is idle:
1. Press the ok key on the key pad. A window will appear showing the level 2 users set up
for the system
2. Select the user from the list and enter the PIN. The numbers entered will be hidden
3. Press the ✓ key to confirm. If the PIN entered is not 5 digits long, the ✓ key will not be
accepted. If the user enters the wrong PIN, a tampering alarm is generated on the
tenth attempt.
4. If the authentication process is successful, the main user menu appears.
2.1.3 Main user menu
The screen is laid out as shown below. When the user accesses this screen, the central unit
automatically switches to the "Arm/disarm" icon
The  key allows you to leave the screen and return to the idle screen. The   arrows allow
you to navigate to select the desired icon and, therefore, function.
Select user
User 1
User 2
User 3
Arm/Disarm

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 8/56
Icon
Meaning
Arm/Disarm. Allows you to access the Arming and Disarming menu for the entire security sys-
tem or for individual zones.
Status and list of events. Provides access to the menu showing the events stored by the cen-
tral unit and the system status.
Panic. Allows a panic alarm to be activated.
Options. Provides access to the menu to adjust the display, audio, date and time, and modify
your PIN
Installer Access. Provides access to the video of the services enabled for a level 3 user.
System test. Provides access to the system test menu.
Exit. Exit the main menu and return the central unit to idle mode.
2.1.4 Status of the individual zones
The status of the zones can be accessed by pressing the  key on the idle screen: each zone
can assume the statuses - and therefore the icons - described in the "Intrusion alarm system"
section of the Meaning of the icons table - par. 2.1.1.
2.2 LEDs
4 LEDs are located beside the display, on the right.
Indicates that the central unit battery is faulty.
Indicates that mandatory notifications have been stored and not yet viewed. Visible when the
system is deactivated.
Signals an alarm (intrusion, tampering).
Does not signal burglar alarms. Only visible to authenticated users.
Signals system jamming.
In the event of a fault or an alarm, the relevant LED will come on and stay on, unless the net-
work power supply is not working and only battery power supply is available. If this is the
case, the LEDs will flash slowly (2 seconds on, 6 seconds off) to save power. The notification
LED will switch off automatically when all of the pending faults have been viewed by scrolling
through the various screens using the F2 key and returning to the main screen.
In the event of alarms (tampering or intrusion), the LED will only switch off following the res-
toration operation.

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 9/56
2.3 Keypad
The touch keypad consists of 17 keys.
   
These are used to navigate the menus and the icons
✓
Confirm the value entered or selected. Press any point on the displayed menu to save the
data and move to the higher menu level.
1 2 3…0
Alphanumerical keys that allow numbers or letters to be entered

Leave the current work session without saving. If pressed when navigating a level 3 menu,
it brings you back to the main level 2 menu used to access it, without losing enabling set-
tings
Remove a setting or a character depending on the context.
2.4 Authentication
In order to access the menus and operate the central unit, authentication is required via an ID
and password, both of which are numerical. The ID and password are stored as codes. Each
user is also assigned specific privileges that determine what they can do. There are no pre-
set factory users. The duration of the work session is 3 minutes for level 2 users and 1 hour
for level 3 users.
2.4.1 User ID
The user ID is a 1 digit numerical code, between 0 and 9, assigned in order by the system
ID 0 is reserved for a level 3 user (installer), ID 1 is for a level 2 user (user) or a level 4 user
(Maintenance personnel).
At least one level 3 user and one level 2 user must be set for each system.
2.4.2 Password
The password (PIN) consists of 5 digits and is chosen freely by the user. The PIN can only be
modified by its owner, using a specific procedure.
2.5 Authorisation level
The authorisation level determines what individual users can and cannot do after authentica-
tion. There are three levels of authorisation:
-Level 2 classifies the users who use the intrusion alarm system on a daily basis.
-Level 3, Installer: can set up or modify the configuration of the system. There can only
be one installer per system. To use the system, a level 3 user must be authorised in
advance by a level 2 user.
-Level 4. Refers to users who can update or change the central unit firmware. Because
this operation is critical to the proper functioning of the system, it is required to ena-
ble users who have already gone through the authentication process using their log-
in details to be authenticated again on a specific basis.
Level 3 Installer users and level 2 Superusers correspond to the authorisation levels of the
same names provided for in regulation EN 50131-1.
The table below outlines the permissions granted to each authorisation level.

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 10/56
Function
Access level
2
3
4
User
Install
er
Maintenance
e person
Global arming
■
■
Only permitted arming
■
■
Total disarming
■
■
Only permitted disarming
■
■
I&HAS restoration
■
■
Check I&HAS functions
■
■
Event register interrogation
■
■
Inhibition / isolation / override (based on
level)
■
■
Addition / changes to individual authorisa-
tion codes (changes can only be made to
your own code)
■
■
Addition / removal of users and level 2
codes
■
Addition / changes to specific site data
■
Changes / replacement of firmware
■

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 11/56
3ARMING AND DISARMING THE SYSTEM
This chapter sets out the procedures for arming and disarming the intrusion alarm system
using the keypad and remote control.
It also explains the procedures to be implemented if the central unit rejects the arming oper-
ation due to faults detected in the system or the individual components.
For remote arming or disarming see chapter Remote commands .
3.1 Arming or disarming using the keypad
3.1.1 Rapid arming or disarming
Total arming or disarming of the system can be performed, or customisable partial arm-
ing/disarming by pressing the  key on the main screen.
If multiple users are set up, select a user from the list and enter the PIN or, if there is only one
user, enter the PIN directly as requested.
A video will appear showing an icon that can be selected directly based on this criterion:
-System with one or more zones armed: disarming icon (as shown in the figure be-
low).
Press OK. The central unit will beep 3 times and the intrusion alarm system will be
disarmed.
-All zones disarmed: global Away mode arming icon appears (as shown in the figure
below)
Press OK The central unit will beep 1 time and the intrusion alarm system will be
armed.
If you wish to select the other option, use the arrows to move and confirm using the OK key.
The rapid arming command can be customised: in this case the central unit performs this
configuration instead of the pre-defined configuration (global away mode arming).
3.1.2 Global arming
The global arming of the intrusion system can only be performed by Users (PIN level 2) and by
the Installer (PIN level 3 - if authorised by a level 2 User) that has permission on all the zones.
Disarm
Arm

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 12/56
To arm the entire intrusion system using the keypad:
1. Log in as a level 2 user
2. The central unit will automatically display the "Arm/Disarm" icon Press OK. Select all
zones
3. Then press OK
4. Using the arrow keys, select:
-Arm Away to arm the system in Arm Away al mode,
-Arm Stay to arm the system in Arm Stay mode,
-Notification to arm the system in Notification mode,
and confirm your selection using the ok key.
The central unit will beep 3 time and the intrusion alarm zones will be armed.
If any event reports are stored in the memory, the zones will not be armed. Instead, the first
unseen event in the memory will be displayed. Select System or Devices to view all events, or
the Force Block item to arm the alarm system anyway (for more information see the following
paragraph Forced Block Arming)
3.1.3 Global disarming
Global disarming of the intrusion system can only be performed by Users (PIN level 2) and by
the Installer (PIN level 3 - if authorised by a level 2 User) that has permission on all the zones.
To disarm the entire intrusion alarm system using the keypad:
1. Repeat points 1 and 2 from the previous paragraph
2. Select "Disarmed".
The central unit will beep 1 time and the intrusion alarm system will be disarmed.
3.1.4 Partial arming
The partial arming of the intrusion system can only be performed by Users (PIN level 2) and
by the Installer (PIN level 3 - if authorised by a level 2 User) on the zones for which they have
been authorized.
Arm/Disarm
All zones
Zone A
Zone B
Arm Away >

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 13/56
To partially arm the intrusion system using the keypad:
1. Repeat points 1 and 2 from the previous paragraph
2. Only the enabled zones will appear. Select the zone that you wish to arm. If a specific
name has been given to the zone during programming, this will appear instead of the
generic names Zone A, Zone B, etc.
3. Using the arrow keys, select:
-Away mode to arm the system in Away mode,
-Home mode to arm the system in Home mode,
-Notification to arm the system in Notification mode,
and confirm your selection using the ok key.
The central unit will beep 3 time and the intrusion alarm zones will be armed.
If you wish to arm other zones, repeat the entire procedure for each zone to be armed
3.1.5 Partial disarming
Partial disarming of the of the intrusion system can be performed by Users (PIN level 2) and
by the Installer (PIN level 3 - if authorised by a level 2 User) on the zones for which they have
been authorized.
To partially disarm the intrusion alarm system using the keypad:
1. Repeat points 1 and 2 from the previous paragraph
2. Select the zone that you wish to disarm. If a specific name has been given to the zone
during programming, this will appear instead of the generic names Zone A, Zone B,
etc.
3. Select "disarmed"
The central unit will beep 1 time and the selected zones will be disarmed.
3.2 Arming or disarming using the remote control
There are two types of remote control:
-Programmable remote control: this can be customised, and so there is not pre-set
key to arm or disarm the entire system.
-Pre-programmed remote control: specific functions are assigned to the keys
Refer to the manual of each remote control for a guide to arming and disarming the system.
3.3 Arming using Forced Block
The intrusion alarm system will not arm in the following cases:
-Detector that is active or faulty.
-Active anti-burglar device.
-Movement detector obstructed or with limited range.
-Tampering.
-Power supply fault (network or battery).
-Faulty siren.
-Problems communicating with the devices.
-Problems with the alarm transmission system (GSM).
-Arming performed using remote control with low batteries
-Other faults
A detector is active if it is signalling an alarm status. For example, the magnetic contact on a
door or window is open. An anti-burglar device is active if it is signalling a burglary attempt.
E.g. a remote control when the burglary button is pressed.

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 14/56
However, a level 2 user can override the block for the zones they are authorised for and arm
the intrusion alarm system. By overriding the block, the central unit will ignore any causes
preventing normal arming of the system and will proceed with the arming.
WARNING!
Block override is an emergency measure to allow partial operation of the intrusion
alarm system. It is important to understand that due to the issues detected, the
protection offered by the system is reduced to a greater or lesser extent. The issues
that caused the block must therefore be resolved as quickly as possible to restore
full system operation.
3.4 Reset
If the alarm system cannot be armed due to potential inhibitions caused by technical alarms,
faults or tampering alarms affecting the detectors, e.g. jamming-supervision, the status of
the central unit or the individual zone should be reset. The function allows you to stop the
persistent fault report caused by failure to transmit the "all clear" signal (e.g. a technical im-
pulsive alarm such as a smoke alarm, flooding alarm, central unit battery, etc.).
The reset operation is recorded in the events log.
To reset the system or an individual zone, proceed as follows:
1. Log in as a level 2 user
2. Select Status and Events and press OK
3. Select Status and press OK
4. Select Alarm Reset: select System to reset the entire system, or the individual zone to
be reset. When the system is reset, all counters relating to multiple alarms will be set
to zero.
Status and Events
Status
1 Central unit
2 Zones and sensors
3 System devices
4 Alarm reset

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 15/56
4PANIC AND BURGLARY
This chapter outlines the procedures for activating the panic and burglar alarms. The panic
alarm is generated voluntarily by the user when a potential danger is presumed. One example
is the threatening presence of an unknown person. The panic alarm sounds the sirens, as a
deterrent, but does not cause telephone messages to be sent.
The burglar alarm is generated voluntarily by the user when they are the victim of a burglary.
This type of alarm does not cause the sirens to sound, to prevent the burglar from reacting.
Instead it disarms the system if armed, and causes telephone alarm reports to be sent.
4.1 Activating the panic alarm
4.1.1 Activation using the keypad
To activate the Panic event, proceed as follows:
1. Log in as a level 2 user
2. Use the arrow keys to select the Panic icon and press ok. To stop the sirens before
the programmed time has elapsed, disarm the system.
4.1.2 Activation using the remote control
Press the remote control button programmed to activate the Panic event. To stop the alarm
by interrupting the programmed siren sound, press the remote control button programmed
to disarm the system. See the remote control manual for more details.
4.2 Activate the burglar alarm
When the burglar alarm is activated, all other alarms that may be active are blocked, the sys-
tem is deactivated if armed, and the burglar alarm voice telephone calls are activated.
4.2.1 Activation using a dedicated button
Press the dedicated button if this has been set up during the installation phase.
4.2.2 Activation using the remote control
Press the remote control button programmed to activate the Burglary event.
To stop the alarm, press the remote control button programmed to deactivate the alarm.
Panic

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 16/56
5ALARMS AND EVENT MEMORIES
5.1 Alarm priority
In the event of multiple simultaneous alarms of different types, only the highest priority
alarm will sound. In the event of alarms with the same priority level, the first one to be trig-
gered will sound. The table below shows the priority level of various types of alarms, where 1
represents maximum priority:
Type of alarm
Priority
Intrusion
1
Tampering.
2
Supervision
3
Low battery
4
System
5
Panic
6
Technical
7
5.2 How to block an alarm
An alarm can be blocked by disarming the alarm system using the keypad, remote control or
remotely. When an alarm is blocked, the sound signals (sirens) and phone reports (voice mes-
sage and SMS) will stop.
Total disarming blocks all types of alarms, while partial disarming may or may not block the
alarm, as shown in the table below:
Type of alarm
Disarming
Total
Alarm zone
Zone
not in alarm mode
Intrusion
Alarm block
Alarm block
Continuous alarm
Tampering.
Alarm block
Alarm block
Continuous alarm
System (1)
Alarm block
Alarm block
Alarm block
Panic (1)
Alarm block
Alarm block
Alarm block
Technical (1)
Alarm block
Alarm block
Alarm block
(1) Also valid in relation to a zone that has already been disarmed
All alarms are stored in the mandatory events memory. An analysis of this memory will reveal
the details of the alarm (when it happened, type of alarm, what device generated the alarm
report, etc.).

BU S C H- /A B B- S EC U RE @ HO M E
2 CSM 6 0 072 7 D0 9 01 17/56
5.3 Events history
Events are recorded in the central unit in two separate memory blocks:
-Mandatory, which may contain up to 250 separate events.
-Optional, which may contain up to 128 separate events.
When the maximum block capacity is reached, the new event overwrites the oldest event in
the memory.
5.3.1 View events
To view events, proceed as follows:
1. Log in as a level 2 user
2. Select Status and events and press OK
3. Select 2 Critical events to examine the main events, 3 to examine the secondary
events.
4. The detailed events screen will open. The events are displayed in order of most recent
to oldest.
Use the  and  keys to scroll through the events.
To read the information relating to the event, see the Interpreting a stored event par-
agraph.
5.3.2 Interpreting a stored event
The data relating to the event is shown on one or more screens. The first screen appears simi-
lar to this:
where:
-[n/t] indicates the progressive number of the event (n) and the total number (t) of
events in the memory.
-Date is the date on which the event occurred.
-Time is the time that the event occurred.
Status and events
Log and status
1 Status
2 Critical events
3 Secondary Events
Event [n/t]
Date Time
Event type
Info 4
Info 5
Info 6
Info 7
<Recent Past>

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 18/56
-Info 4 … Info 7 provides additional information that varies according to the type of
event and that is specified in the tables below.
- and  allows you to scroll forward and backward through the events
Main events (mandatory)
Event type
Info 4
Info 5
Info 6
Info 7
Second screen (Inf)
Input
System / Zone
armed
Name or ID of the
user who armed
the system
Device used
for the op-
eration
Previous zone sta-
tus
Status following
arming
Disarming
Disarmed sys-
tem / zone
Name or ID of the
user who dis-
armed the system
Device used
for the op-
eration
Previous zone sta-
tus
Status following
disarming
Burglar alarm
Name or ID of the
user performed
the operation
Device used
for the op-
eration
Intrusion alarm
Type of Sensor
Sensor Position
Tampering alarm
Type of Sensor
Sensor Position
Supervision
Type of Sensor
Sensor Position
Radio jamming
alarm
Central unit
Tampering
Central unit
Detector exclu-
sion
Type of Sensor
Position
User ID
Block override
Arming
User name or ID
Device used
Fault – Fault type
Type of Sensor
Position
Low battery
Type of Sensor
Position
Level 2 user
added by level 3
user
New User L. 2-3
PIN Lev3
Index
PIN Lev2
Index
Date and time
change
User ID
Num. Variation
Telephone
User ID
Central unit SW
Update
User ID
Central unit
start-up
Periodic GSM in-
spections
Tel. ID (1)
No network
power supply
Battery Level

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 19/56
Network power
supply return
Battery Level
No 230V
Network
time OFF
minutes
Voice call
Alarm type
Telephone ID
calls (1)
Send SMS
Alarm type
telephone IDs
recipients
(1) In bold if the call was successful, i.e. the recipient picked up; normal if the call was unsuc-
cessful.
Secondary events (optional)
Event type
Info 4
Info 5
Info 6
Info 7
Second screen
Intrusion pre-
alarm
Type of Sensor
Position
Sensor
Login
User ID
Logout
User ID

BU S C H- /A B B- S EC U RE @ HO ME
2 CSM 6 0 072 7 D0 9 01 20/56
6REMOTE COMMANDS
If enabled, it is possible to interact with the central unit remotely with GSM using telephone
lines and DTMF tones or SMS messages. The central unit must be equipped with an active
SIM Card.
6.1 Telephone commands with DTMF tones
The central unit telephone number can be called from any telephone, as long as DTMF tones
can be sent. The telephone number used to place the call does not need to be included
among the numbers stored by the central unit.
Caller authentication and privileges to operate the central unit are guaranteed using the
same ID-password system used to perform authentication on the central unit keypad.
Phone sessions last a maximum of 1 minute before the arming is interrupted by the central
unit. During this time, the user can send any commands it wants to the central unit.
To send commands using DTMF tones:
1. Dial the telephone number of the central unit (the one on the SIM Card installed in the
central unit).
2. The central unit will respond with the voice message "Enter User and press asterisk".
Use the telephone keypad to input a level 2 or 3 user ID (1 digit) and press the * key to
confirm.
3. The central unit will respond with the voice message "Enter PIN and press asterisk".
Use the keypad to enter the telephone password (5 digits) combined with the ID code
sent previously and press the * key to confirm.
4. If the ID-password pair is incorrect, the central unit will respond with the voice mes-
sage "Incorrect user" and repeat the procedure from point 1. After 5 failed authentica-
tion attempts, the phone call will be interrupted and the episode will be stored in the
events log as "Tampering from telephone no. xxxxxxxxxx”. If the number is hidden,
the caller will not be recorded in the log.
If the authentication process is successful, the central unit will respond with the voice mes-
sage "Enter command and press asterisk". Use the keypad to enter the command code (2 dig-
its) specified in the table below and press the * key to confirm.
List of DTMF Commands
Function
Drive
DTMF Code
Anti-intrusion (all of the zones for which the user placing the call is au-
thorised)
Activate
11
Deactivate
10
Command 1
Activate
41
Deactivate
40
Command 2
Activate
51
Deactivate
50
Command 3
Activate
61
Deactivate
60
Command 4
Activate
71
Deactivate
70
Command 5
Activate
81