ABB i-bus KNX FCL/S 1.6.1.1 User manual

ABB i-bus®KNX
Blower Actuator FCL/S x.6.1.1
Product Manual

ABB i-bus®KNX
Contents
FCL/S x.6.1.1 | 2CDC508116D0203 i
Contents
Page
1General ................................................................................................. 3
1.1 Using the product manual.............................................................................................................3
1.1.1 Notes............................................................................................................................................4
1.2 Product and functional overview...................................................................................................5
2Device technology............................................................................... 7
2.1 FCL/S x.6.1.1 Blower Actuator x-fold, 6 A, MDRC........................................................................7
2.1.1 Technical data..............................................................................................................................7
2.1.2 Lamp output load at 230 V AC ....................................................................................................10
2.1.3 Connection diagrams..................................................................................................................11
2.1.4 Dimension drawings ...................................................................................................................12
2.2 Mounting and installation............................................................................................................13
3Start-up............................................................................................... 15
3.1 Overview.....................................................................................................................................15
3.1.1 Output functions .........................................................................................................................16
3.2 Parameters.................................................................................................................................17
3.2.1 Parameter window General........................................................................................................18
3.2.2 Parameter window Enable outputs A...F ....................................................................................20
3.2.2.1 Parameter window A: Fan (Multi-level).......................................................................................21
3.2.2.1.1 Parameter window - Status messages (Multi-level)....................................................................25
3.2.2.1.2 Parameter window - Automatic control (Multi-level)....................................................................30
3.2.2.1.3 Parameter window - Direct operation .........................................................................................38
3.2.2.1.4 Parameter window - Startup/Run-on ..........................................................................................40
3.2.2.2 Parameter window A: Fan (Two-level)........................................................................................43
3.2.2.3 Parameter window - A: Fan (One-level) .....................................................................................44
3.2.2.3.1 Parameter window - Status messages (One-level).....................................................................47
3.2.2.3.2 Parameter window - Automatic control (One-level) ....................................................................49
3.2.2.4 Parameter window B: Output......................................................................................................55
3.2.2.4.1 Parameter window B: Output - Time...........................................................................................58
3.2.3 Commissioning without bus voltage ...........................................................................................62
3.3 Communication objects ..............................................................................................................63
3.3.1 Summary of communication objects...........................................................................................63
3.3.2 Communication objects General.................................................................................................66
3.3.3 Communication objects Fan A and Fan CDE.............................................................................67
3.3.3.1 Communication objects Fan Multi-level......................................................................................67
3.3.3.2 Communication objects Fan One-level.......................................................................................73
3.3.4 Communication objects Output...................................................................................................78

ABB i-bus®KNX
Contents
ii 2CDC508116D0203 | FCL/S x.6.1.1
4Planning and application...................................................................81
4.1 Fan output.................................................................................................................................. 81
4.1.1 Fan operation............................................................................................................................. 82
4.1.1.1 Fan with changeover switch....................................................................................................... 83
4.1.1.2 Fan with step switch................................................................................................................... 83
4.1.2 Automatic control....................................................................................................................... 84
4.1.3 Direct operation ......................................................................................................................... 86
4.1.4 Switchover between automatic and direct operation.................................................................. 86
4.1.5 Speed switching logic ................................................................................................................ 87
4.1.6 Fan operation functional diagram .............................................................................................. 88
4.2 Switch output............................................................................................................................. 89
4.2.1 Function diagram....................................................................................................................... 89
4.2.2 Time function............................................................................................................................. 90
4.2.2.1 Staircase lighting ....................................................................................................................... 90
4.3 Application example: Switching heating and cooling valves ...................................................... 91
4.4 Reaction on bus voltage failure, recovery, download and ETS reset......................................... 92
4.4.1 Bus voltage recovery ................................................................................................................. 92
4.4.2 Bus voltage recovery ................................................................................................................. 92
4.4.3 ETS reset................................................................................................................................... 93
4.4.4 Download................................................................................................................................... 93
4.4.5 Tabular overview of bus voltage recovery, download and ETS reset ........................................ 94
4.5 Priorities..................................................................................................................................... 95
AAppendix.............................................................................................97
A.1 Scope of delivery....................................................................................................................... 97
A.2 Fan status byte, forced/operation .............................................................................................. 98
A.3 Ordering details ......................................................................................................................... 99
A.4 Notes ....................................................................................................................................... 100

ABB i-bus®KNX
General
FCL/S x.6.1.1 | 2CDC508116D0203 3
1 General
The Blower Actuator FCL/S x.6.1.1 is used in ventilation applications.
It is a compact device that serves the following functions:
Controlling fans and blowers
Switching loads
Outputs that are not being used for fan functions can be used as switch actuators for switching electrical
loads.
1.1 Using the product manual
This manual provides detailed technical information on the function, installation and programming of the
ABB i-bus® KNX device.
This manual is divided into the following chapters:
Chapter 1
General
Chapter 2
Device technology
Chapter 3
Start-up
Chapter 4
Planning and application
Chapter A
Appendix

ABB i-bus®KNX
General
4 2CDC508116D0203 | FCL/S x.6.1.1
1.1.1 Notes
Notes and safety instructions are represented as follows in this manual:
Note
Tips for usage and operation
Examples
Application examples, installation examples, programming examples
Important
These safety instructions are used as soon as there is danger of a malfunction without risk of damage
or injury.
Caution
These safety instructions are used as soon as there is danger of a malfunction without risk of damage
or injury.
Danger
These safety instructions are used if there is a danger to life and limb with inappropriate use.
Danger
These safety instructions are used if there is an extreme danger to life with inappropriate use.

ABB i-bus®KNX
General
FCL/S x.6.1.1 | 2CDC508116D0203 5
1.2 Product and functional overview
The FCL/S 1.6.1.1 and FCL/S 2.6.1.1 Blower Actuators are modular installation devices in ProMdesign 4-
and 8-module widths for installation in a distribution board. Connection to the ABB i-bus KNX is estab-
lished via the front bus connection terminal. The devices require no auxiliary voltage. The assignment of
physical addresses as well as the parameterization is carried out with Engineering Tool Software ETS.
The FCL/S 1.6.1.1 1-fold actuator controls a single-phase fan with up to three fan speeds via a step or
changeover control. The FCL/S 2.6.1.1 2-fold actuator can control a second fan. The actuators ensure that
no two fan speeds can be switched on simultaneously.
The outputs on the 2-fold actuator that are not used for the fan can be used to switch electrical loads.
The device receives its control value via the ABB i-bus®KNX, e.g. from a room thermostat.
The following controls are feasible:
FCL/S 1.6.1.1:
One 3-speed fan plus one switch output
FCL/S 2.6.1.1:
Two 3-speed fans plus two switching outputs
One 3-speed fan plus five switching outputs

ABB i-bus®KNX
Device technology
FCL/S x.6.1.1 | 2CDC508116D0203 7
2 Device technology
2.1 FCL/S x.6.1.1 Blower Actuator x-fold, 6 A, MDRC
FCL/S 2.6.1.1
The FCL/S x.6.1.1 Blower Actuator is a
modular installation device (MDRC) in
ProMdesign. It is intended for installation
in the distribution board on 35 mm mount-
ing rails. The assignment of the physical
address as well as the parameterization
is carried out using ETS and the current
application.
The device is powered via the
ABB i-bus®KNX and requires no addi-
tional auxiliary voltage supply.
The device is ready for operation after
connecting the bus voltage.
2.1.1 Technical data
Power supply
KNX bus voltage
21…32 V DC
Current consumption, bus
< 12 mA
Power consumption
Maximum 250 mW
Rated output value
FCL/S Type
1.6.1.1 2.6.1.1
Number
4 8
Unrated voltage
250/440 V AC (50/60 Hz)
Inrated current (per output)
6 A 6 A
Leakage loss per device at max. load
1.5 W 2.0 W
Output switching current
AC32) operation (cos = 0.45)
To EN 60 947-4-1
6 A/230 V AC
AC12) operation (cos = 0.8)
To EN 60 947-4-1
6 A/230 V AC
Fluorescent lighting load to EN 60 669-1
6 A/250 V AC (35 F)1)
Minimum switching capacity
20 mA/5 V AC
10 mA/12 V AC
7 mA/24 V AC
Output service life
Mechanical service life
> 107
Electronic endurance
to IEC 60 947-4-1
AC12) (240 V/cos = 0.8)
> 105
AC32) (240 V/cos = 0.45)
> 1.5 x 104
AC5a2) (240 V/cos = 0.45)
> 1.5 x 104
1) The maximum inrush current peak may not be exceeded.
2CDC071026S0012

ABB i-bus®KNX
Device technology
8 2CDC508116D0203 | FCL/S x.6.1.1
2) What do the terms AC1, AC3 and AC5a mean?
In Intelligent Building Control, different switching capabilities and performance specifications, required by
special applications, have become established in industrial and residential systems. These performance
specifications are rooted in the respective national and international standards. The tests are defined to
simulate typical applications, e.g. motor loads (industrial) or fluorescent lamps (residential).
Specifications AC1 and AC3 are switching performance specifications which have become established in
the industrial field.
Typical application:
AC1 –Non-inductive or slightly inductive loads, resistive furnaces (relates to switching of ohm-
ic/resistive loads)
AC3 –Squirrel-cage motors: Starting, switching off motors during running (relates to (inductive)
motor load)
AC5a –Switching of electric discharge lamps
These switching performances are defined in standard EN 60 947-4-1 Contactors and motor-starters –
Electromechanical contactors and motor-starters. The standard describes starters and/or contactors that
were originally used primarily in industrial applications.

ABB i-bus®KNX
Device technology
FCL/S x.6.1.1 | 2CDC508116D0203 9
Output switching times3)
Maximum output relay position change per mi-
nute if all relays are switched simultaneously.
The position changes should be distributed
equally within the minute.
1.6.1.1 2.6.1.1
60 30
Maximum output relay position change per mi-
nute if only one relay is switched.
240 240
Connections
KNX
Via bus connection terminals,
0.8 mm Ø, solid
Load circuits
Screw terminal
0.2…2.5 mm2fine stranded
0.2...4 mm2solid
Tightening torque
max. 0.6 Nm
Operating and display elements
Programming Button/LED
For assignment of the physical address
Degree of protection
IP 20
To EN 60 529
Protection class
II
To EN 61 140
Isolation category
Overvoltage category
III to EN 60 664-1
Pollution degree
2 to EN 60 664-1
KNX safety extra low voltage
SELV 24 V DC
Temperature range
Operation
Storage
Transport
-5 °C…+45 °C
-25 °C…+55 °C
-25 °C…+70 °C
Ambient conditions
Maximum air humidity
95 %, no condensation allowed
Design
Modular installation device (MDRC)
Modular installation device, ProM
FCL/S Type
1.6.1.1 2.6.1.1
Dimensions
90 x W x 64.5 mm (H x W x D)
Width W in mm
72 108
Mounting width in units (18 mm modules)
4 6
Mounting depth in mm
64.5 64.5
Weight
1.6.1.1 2.6.1.1
in kg
0.13 0.24
Installation
On 35 mm mounting rail
To EN 60 715
Mounting position
As required
Housing/color
Plastic housing, gray
Approvals
KNX to EN 50 090-1, -2
Certification
CE mark
In accordance with the EMC guideline and low
voltage guideline
3) The specifications apply only after the bus voltage has been applied to the device for at least 30 seconds. Typical relay delay is approx. 20 ms.

ABB i-bus®KNX
Device technology
10 2CDC508116D0203 | FCL/S x.6.1.1
2.1.2 Lamp output load at 230 V AC
Lamps
Incandescent lamp load
1200 W
Fluorescent lamps T5/T8
Uncorrected
Parallel compensated
DUO circuit
800 W
300 W
350 W
Low-voltage halogen lamps
Inductive transformer
Electronic transformer
Halogen lamps 230 V
800 W
1000 W
1000 W
Dulux lamp
Uncorrected
Parallel compensated
800 W
800 W
Mercury-vapor lamp
Uncorrected
Parallel compensated
1000 W
800 W
Switching capacity (switching contact)
Maximum peak inrush current Ip(150 s)
Maximum peak inrush current Ip(250 s)
Maximum peak inrush current Ip(600 s)
200 A
160 A
100 A
Number of electronic ballasts
(T5/T8, single element)1)
18 W (ABB EVG 1 x 18 SF)
24 W (ABB EVG-T5 1 x 24 CY)
36 W (ABB EVG 1 x 36 CF)
58 W (ABB EVG 1 x 58 CF)
80 W (Helvar EL 1 x 80 SC)
10
10
7
5
3
1) For multiple element lamps or other types the number of electronic ballasts must be determined using the peak inrush current of the ballasts.
Device type
Application
Maximum number of
Communication objects
Maximum number of
group addresses
Maximum number of
associations
FCL/S 1.6.1.1
Switch Blower 1f 6A/1.0*
64
254
254
FCL/S 2.6.1.1
Switch Blower 2f 6A/1.0*
124
254
254
* … = current version number of the application. Please refer the software information on our homepage for this purpose.
Note
ETS and the current version of the device application are required for programming.
The current version of the application is available for download at www.abb.com/knx. After import into
ETS it appears in the Catalogs window under Manufacturers/ABB/Heating, Ventilation, Air condition-
ing/Ventilation actuator.
The device does not support the locking function of a KNX device in ETS. If you use a BCU code to
inhibit access to all the project devices, it has no effect on this device. Data can still be read and pro-
grammed.

ABB i-bus®KNX
Device technology
FCL/S x.6.1.1 | 2CDC508116D0203 11
2.1.3 Connection diagrams
FCL/S 1.6.1.1
FCL/S 2.6.1.1 (2 fans)
FCL/S 2.6.1.1 (1 fan)
1
Label carrier
2
Programming button
3
Programming LED (red)
4
Bus connection terminal
5
Power outputs
2CDC072072F0011
2CDC072018F0012
2CDC072070F0011

ABB i-bus®KNX
Device technology
12 2CDC508116D0203 | FCL/S x.6.1.1
2.1.4 Dimension drawings
FCL/S 1.6.1.1
FCL/S 2.6.1.1
2CDC072071F0011
2CDC072073F0011

ABB i-bus®KNX
Device technology
FCL/S x.6.1.1 | 2CDC508116D0203 13
2.2 Mounting and installation
The device is a modular installation device for quick installation in the distribution board on 35 mm mount-
ing rails to EN 60 715.
The mounting position can be selected as required.
The electrical connection is implemented using screw terminals. The connection to the bus is implemented
using the supplied bus connection terminal. The terminal assignment is located on the housing.
The device is ready for operation after connection to the bus voltage.
Accessibility of the devices for the purpose of operation, testing, visual inspection, maintenance and repair
must be provided compliant to VDE 0100-520.
Commissioning requirements
To commission the device you need a PC with ETS (ETS3 or higher) and an interface (e.g. KNX) to the
ABB i-bus®.
The device is ready for operation after connection to the bus voltage. No additional auxiliary voltage is re-
quired.
Important
The maximum permissible current of a KNX line may not be exceeded.
During planning and installation ensure that the KNX line is correctly dimensioned.
The device features a maximum current consumption of 12 mA (Fan-In 1).
Mounting and commissioning may only be carried out by electrical specialists. The appropriate standards,
guidelines, regulations and specifications for your country should be observed when planning and setting
up electrical installations and security systems for intrusion and fire detection.
Protect the device from damp, dirt and damage during transport, storage and operation.
Only operate the device within the specified technical data!
The device should only be operated in an enclosed housing (distribution board)!
The voltage supply to the device must be switched off before mounting work is performed.
Danger
To avoid dangerous touch voltages which originate through feedback from differing phase conductors,
all poles must be disconnected when extending or modifying the electrical connections.

ABB i-bus®KNX
Device technology
14 2CDC508116D0203 | FCL/S x.6.1.1
Supplied state
The device is supplied with the physical address 15.15.255. The application is pre-installed. It is therefore
only necessary to load group addresses and parameters during commissioning.
However, the complete application can be reloaded if required. Downloads may take longer after a change
of application or a discharge.
Assignment of the physical address
The assignment and programming of the physical address is carried out in ETS.
The device features a button for assignment of the physical device address. The red LED lights up
after the button has been pushed. It switches off as soon as ETS has assigned the physical address or the
button is pressed again.
Download response
The progress bar for download may take up to 1.5 minutes to appear depending on the PC that is used,
because of the complexity of the device.
Cleaning
If devices become dirty they can be cleaned using a dry cloth or a cloth dampened with a soapy solution.
Corrosive agents or solutions should never be used.
Maintenance
The device is maintenance-free. No repairs should be carried out by unauthorized personnel if damage
occurs, e.g. during transport and/or storage.

ABB i-bus®KNX
Start-up
FCL/S x.6.1.1 | 2CDC508116D0203 15
3 Start-up
The blower actuator is parameterized with the Switch Blower 1f 6A/1.0 (FCL/S 1.6.1.1) or Switch Blow-
er 2f 6A/1.0 (FCL/S 2.6.1.1) application, and ETS Engineering Tool Software. The application provides the
device with a comprehensive and flexible range of functions. The standard settings allow simple commis-
sioning. The functions can be extended if required.
3.1 Overview
The following functions are available:
Fan
A three-speed fan is controlled alternately with a two-way connection or with speed
switching.
stagePower outlets (sockets)
For power supply to individual power outlet circuits and other loads.
Illumination
For power supply to individual lighting circuits and other loads.
Caution
Improper switching will destroy the fan motors.
Follow the technical data for the fan, e.g. speed or switching function.
For further information see: Parameter window A: Fan (Multi-level), p.21.
The blower actuator features relays in each output which are mechanically independent of the other out-
puts. Switching noises cannot be avoided due to the mechanical nature of the design.
The device is installed primarily in the distribution board together with the circuit-breakers and RCCBs.
Usually, the blower actuator is used in conjunction with a room thermostat for an individual room tempera-
ture control system. The room thermostat sends a control value which the blower actuator uses to control
the fan speeds.

ABB i-bus®KNX
Start-up
16 2CDC508116D0203 | FCL/S x.6.1.1
3.1.1 Output functions
The following table provides an overview of the functions possible when you combine the device outputs
with the Switch Blower 1f 6A/1.0 (FCL/S 1.6.1.1) or Switch Blower 2f 6A/1.0 (FCL/S 2.6.1.1) application.
Output functions
A
B
C, D, E*
F*
Fan


NO contact/NC contact



Time
Staircase lighting



= Function is supported
* FCL/S 2.6.1.1 only
Note
Outputs C, D and E can also be programmed as switch actuators. The settings options are described in
Parameter window A: Fan (Multi-level), p.21.

ABB i-bus®KNX
Start-up
FCL/S x.6.1.1 | 2CDC508116D0203 17
3.2 Parameters
ETS Engineering Tool Software is used for parameterizing the device.
In ETS, the application appears in the Catalogs window under Manufacturers/ABB/Heating, Ventilation, Air
conditioning/Ventilation actuator.
The following chapter describes the parameters of the device using the parameter windows. Parameter
windows are structured dynamically so that further parameters may be enabled depending on the parame-
terization and function of the outputs.
The default values of the parameters are underlined, e.g.:
Options: Yes
No
Note
The FCL/S 1.6.1.1 outputs are:
A: Fan output
B: Switch actuator output
The FCL/S 2.6.1.1 outputs are:
A: Fan output
B: Switch actuator output
C, D, E: One fan output or parameterizable as switch actuators
F: Switch actuator output
Note
All parameter window descriptions and control options refer to the FCL/S 2.6.1.1 2-fold Blower Actuator.
The application for the FCL/S 1.6.1.1 1-fold Blower Actuator has no Enable outputs A…F parameter
window, i.e. output A is always a fan output and the additional switch output B is always activated.

ABB i-bus®KNX
Start-up
18 2CDC508116D0203 | FCL/S x.6.1.1
3.2.1 Parameter window General
This is the parameter window where you can set higher level parameters.
Sending and switching delay after bus
voltage recovery in s [2…255]
Options: 2…255
During the sending and switching delay, telegrams are received only. The telegrams are not processed,
however, and the outputs remain unchanged. No telegrams are sent via the bus.
After the sending and switching delay, telegrams are sent and the state of the outputs is set to correspond
with the parameterization or the communication object values.
If communication objects are read during the sending and switching delay, e.g. by a visualization system,
these read requests are stored, and a response is sent, after the sending and switching delay has been
completed.
An initialization time of about two seconds is included in the delay time. The initialization time is the time
that the processor requires to be ready to function.
How does the device react on bus voltage recovery?
After bus voltage recovery, the device always waits for the transmission delay time to elapse before send-
ing telegrams via the bus.