Abb M22001 series User manual

VER:1.0 │ │ 22.04.2015

ABB-Welcome

Pos: 2 /Di nA4 - A nleitungen O nline/Inhalt/KN X/DoorE ntry/83220- AP-xxx/Tit elblatt - 83220-AP- xxx- ABB @ 19\mod _1323249 806476_15.doc x@ 11108 4@ @ 1

M22001-.

M22002-.

M22003-.

Audio handset indoor station

=== Ende der List ef ürT extmarke Cover == =

ABB-Welcome

—2 —

Pos: 4 /Busch-J aeger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Inhal tsverzeichnis (--> Für alle D okumente <--)/Inhalts verzeichnis @ 19\mod _1320649 044386_1 5.docx @ 109653 @ @ 1

1Safety............................................................................................................3

2Intended use..................................................................................................3

3Environment ..................................................................................................3

3.1 ABB devices.................................................................................4

4Operations.....................................................................................................5

4.1 Standard operations .....................................................................5

4.1.1 Control elements ..........................................................................5

4.2 Settings.........................................................................................7

4.2.1 Ringtone type settings..................................................................7

4.2.2 Default outdoor station settings....................................................7

4.2.3 Programming the auxiliary buttons ...............................................7

4.3 Adjusting the device......................................................................9

5Technical data.............................................................................................11

6Mounting / Installation..................................................................................12

6.1Requirements for the electrician.................................................12

6.2 General installation instructions..................................................13

6.3 Mounting.....................................................................................14

=== Ende der List efür T extmarke TOC ===

ABB-Welcome

Safety

—3 —

Pos: 6 /Busch-J aeger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Übers chriften (--> Für alle Doku mente <--)/1. Ebene/S - T/Sicherheit @ 18\ mod_1302 612791790_15.doc x@ 10335 7@ 1 @ 1

1 Safety

Pos: 7 /Busch-Jaeger (Ne ustruktur)/Modul-Str uktur/Online-Doku mentation/Sicherh eit( -->F ürall eD okument e<--)/W arnhinweise/Sicherh eit- 23 0V @ 18\m od_13026068167 50_15.doc x@ 103 308 @ @ 1

Warning

Electric voltage!

Risk of death and fire due to electrical voltage of 100-240 V.

–Work on the 100-240V supply system may only be performed by

authorised electricians!

–Disconnect the mains power supply prior to installation and/or

disassembly!

Pos: 8 /Busch-J aeger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Übers chriften (--> Für alle Doku mente <--)/1. Ebene/A - F/Bestimmungsg emäßer Gebrauch @ 18\mo d_130276332131 6_15.docx @ 1034 83 @ 1 @ 1

2 Intended use

Pos: 9 /DinA4 - Anleit ungen O nline/Inhalt/KNX/D oorEntry/83220- AP-xxx/Besti mmungsgema esser Gebrauch - 8 3220-AP-xxx-500 @ 20\mod_1 32456116 8699_15.d ocx @ 112728 @ @ 1

The M2200x-x indoor station is an integral part of the ABB Welcome door entry system

and operates exclusively with components from this system. The device must only be

installed in dry indoor rooms.

Pos: 10 /Busch-J aeger (Neustru ktur)/Modul- Struktur/Online-D okumentation/Üb erschriften (--> Für alle D okumente <--)/1. Ebene/U - Z/Um welt @ 18\mod _1302614 158967_15.docx @ 103383 @ 1 @ 1

3 Environment

Pos: 11 /B usch-J aeger (Ne ustruktur)/Mo dul-Struktur /Online-Do kumentation/U mwelt (--> Für alle D okumente <--)/Hinw eise/Hi nweis - Umwelt - Hinweis Elektrog eräte @ 18\mod_1302 76397343 4_15.docx @ 1035 00@ @ 1

Consider the protection of the environment!

Used electric and electronic devices must not be disposed of with

domestic waste.

–The device contains valuable raw materials which can be recycled.

Therefore, dispose of the device at the appropriate collecting

depot.

Pos: 12 /DinA4 - Anl eitungen Online/Ueb erschriften/2./ABB G eraete @ 19\mod_13 23162843832_ 15.docx @ 110875 @ 2 @ 1

ABB-Welcome

Environment

—4 —

3.1 ABB devices

Pos: 13 /B usch-J aeger (Ne ustruktur)/Mo dul-Struktur /Online-Do kumentation/U mwelt (--> Für alle D okumente <--)/Hinw eise/Hi nweis - Umwelt - ABB Elektrogerä te@ 1 9\mod_13231627 45839_15.docx @ 110867 @ @ 1

All packaging materials and devices from ABB bear the markings and test seals for

proper disposal. Always dispose of the packaging material and electric devices and their

components via the authorized collecting depots and disposal companies.

ABB products meet the legal requirements, in particular the laws governing electronic

and electrical devices and the REACH ordinance.

(EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS)

(EU-REACH ordinance and law for the implementation of the ordinance (EG)

No.1907/2006)

ABB-Welcome

Operations

—5 —

Pos: 18 /DinA4 - Anl eitungen Online/Ueb erschriften/1./Bedi enung @ 18\mod_ 1302613924165_15. docx @ 103365 @ 1 @ 1

4 Operations

Pos: 19 /DinA4 - Anl eitungen Online/Ueb erschriften/2./Nor maler Betrieb @ 18\m od_13027688209 65_15.docx @ 103540 @ 2 @ 1

4.1 Standard operations

Pos: 20 /DinA4 - Anl eitungen Online/Ueb erschriften/3./Bedi enelemente @ 20\mo d_132326022 0559_15.docx @ 1116 47@ 3 @ 1

4.1.1 Control elements

Pos: 21 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/8 3220-AP-xxx/Bedienelem ente- 832 20-AP- xxx@ 1 8\mod_ 13032128 53605_15.docx @ 103673 @ @ 1

Fig.

Control elements

ABB-Welcome

Operations

—6 —

No.

Function

Handset

When a call is coming, pick up the handset to activate communication

within 30 seconds and hang up the handset to end the call.

Unlock button

2A Press this button to open the door at any time.

2B auto-unlock: the door is automatically opened for an incoming call

(hold this button for over 10 seconds until the blue LED turns on; the

same operation will switch off the function and the blue LED will turn off).

Programmable button

3A *Programmable for additional functions, e.g. call guard unit, intercom.....

3B Default function of button 1 is the release of the lock connected with an

outdoor station (COM-NC-NO).

Three-level selector for call volume adjustment (maximum/ medium /

mute).

LED (Red)

- indicating that the

door is open over the

set time (The sensor

must be connected)

- when any button is

pressed.

- indicating mute.

LED (Blue)

- indicating that the

system is busy.

- indicating an

Incoming call.

- indicating auto-

unlock.

**Induction loop function

*For their use, please contact your electrical installer.

Pos: 22 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/Ste uermodule - Onli ne-Dokument ation(--> F ür alle Do kumente <--)/++++++ ++++++ Seitenumbruch ++++++++ ++++ @ 9\mod_12688 98668093_0.docx @ 52149 @ @ 1

**This function is only available in M22003-.

ABB-Welcome

Operations

—7 —

4.2 Settings

4.2.1 Ringtone type settings

Pos: 21 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/8 3220-AP-xxx/Bedienelem ente- 832 20-AP- xxx@ 1 8\mod_ 13032128 53605_15.docx @ 103673 @ @ 1

1. Hold " + " for about 3 seconds to enter the system setting mode (with

blue LED & red LED flashing simultaneously).

2. Press to set the next ringtone type for the door bell.

3. Press to set the next ringtone type for a call from an outdoor station.

4. Press to set the next ringtone type for an intercom call from other apartments

or the guard unit.

5. Hold " + " for about 3 seconds to save the selected ringtone type and

exit the system setting mode..

4.2.2 Default outdoor station settings

Pos: 21 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/8 3220-AP-xxx/Bedienelem ente- 832 20-AP- xxx@ 1 8\mod_ 13032128 53605_15.docx @ 103673 @ @ 1

1. Pickup the handset, hold for about 3 seconds to enter the default outdoor

station setting mode.

2. Press button to set the address of the default outdoor station. (the value is

indicated by the flash times of the red LED; it can be set from 1 to 9, default

setting: 1).

3. Hold for about 3 seconds or put down the handset to save the setting and

exit the settings mode.

4.2.3 Programming the auxiliary buttons

Pos: 21 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/8 3220-AP-xxx/Bedienelem ente- 832 20-AP- xxx@ 1 8\mod_ 13032128 53605_15.docx @ 103673 @ @ 1

Each programmable button is available only after setting. These buttons can be

set for different functions, e.g. call guard unit, intercom call or controls switch

actuator.

1. Enter the programming mode

Hold the programmable button for 3 seconds in the standby mode to enter the

programming mode.

2. Set the function for each programmable button

Check the needed function, and press to program the corresponding function

code which is indicated by the flash times of the blue LED.

●The function code can be changed: 0->1->2->3->4->5->0.

ABB-Welcome

Operations

—8 —

Function list

Function code

Blue LED flashing

No function

Always on

Control switch actuator

Flash once

Intercom call in the same apartment

Flash twice

Intercom call among different

apartments

Flash 3 time

Call guard unit

Flash 4 time

Release 2nd-lock of a default

outdoor station (the lock connected

with an outdoor station COM-NC-

NO)

Flash 5 time

Function code is indicated by flash times of blue LED; if the Blue LED is always on, this

represents code 0.

3. Set the address for each programmable button

Only the following two functions are assigned to the programmable buttons, The

address of each programmable button is needed to be set. Other functions are

inapplicable to this step.

Function 1: Controls switch actuator. Set the address of the switch actuator under

control. The address can be set from 01 to 99.

Function 2: Intercom call among different apartments. Set the address of an indoor

station which is called. The address can be set from 01 to 99.

Hold this programmable button again for 3 seconds until the LED begins to flash

(tens digit or units digit address is other than 0) or lights on (tens digit or units digit

address is 0) to enter the address settings mode.

Press repeatedly to set the tens digit. Each press means one increment to

the previous address. The value is indicated by the flash times of the red LED.

Press repeatedly to set the units digit in the same manner. The value is

indicated by the flash times of the blue LED.

Both tens digit and units digit can be changed in a sequence of: 0->1->2->3->4->5-

>6->7->8->9->0 by pressing or .

ABB-Welcome

Operations

—9 —

During settings, if the value set is beyond the wanted number, press , both

tens digit and units digit will go back to the default value 0.

4. Exit the programming mode

Hold this programmable button for 3 seconds until the blue LED & red LED flash

once simultaneously.

Pos: 67 /DinA4 - Anleitungen Online /Ueberschriften/2./Rei nigung @ 19\mod_1310 733980 533_15.docx @ 107853 @ 2 @ 1

Pos: 70 /DinA4 - Anl eitungen Online/Ueb erschriften/2./Gera eteeinstellungen @ 18\ mod_130276 8847744_15.docx @ 1 03548 @ 2 @ 1

4.3 Adjusting the device

Pos: 71 /DinA4 - Anl eitungen Online/Ueb erschriften/3./Absc hlusswiderstand @ 19\m od_132195807 9906_15.docx @ 1100 83@ 3 @ 1

Pos: 72 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/B edienung/Abschl usswiderstand setze n 83220-AP- xxx@ 19\ mod_131072339 2369_15.docx @ 107841 @ @ 1

Fig.

Pos: 74 /DinA4 - Anl eitungen Online/Inhalt/ KNX/DoorEntry/B edienung/Mast er/Slave Schalter setz en8 3220-AP-xxx @ 19\mod_1310 72332096 6_15.docx @ 10 7833 @ @

1. X100 X10 X1

Jumper to set the address of the indoor station.

EXAMPLE: setting address 024

2. Master /Slave function

Only one indoor station in each apartment must be set as "Master" (Jumper should

ABB-Welcome

Operations

—10 —

be set as 'M/S on'). All additional indoor stations in the same apartment must be

set as "Slave" (Jumper should be set as 'M/S off').

3. Terminal resistor

In video installations or mixed audio and video installations, the Jumper must be

set as 'RC on' on the last device of the line.

4. a b = Bus connection

= Door bell connection

Pos: 75 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/Ste uermodule - Onli ne-Dokument ation(--> F ür alle Do kumente <--)/++++++ ++++++ Seitenumbruch ++++++++ ++++ @ 9\mod_12688 98668093_0.docx @ 52149 @ @ 1