ABB TTH200 User manual

—
ABB MEASUREMENT & ANALYTICS | OPERATING INSTRUCTION
TTH200
Head-mount temperature transmitter
—
ABB Limited
Measurement & Analytics
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: [phone]
Fax: [phone]
Email: [email protected]m
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
abb.com/temperature
ABB Inc.
Measurement & Analytics
125 E. County Line Road
Warminster, PA 18974
USA
Tel: [phone]
Fax: [phone]
Temperature transmitter for HART
protocol.
Suitable for all standard
requirements
Measurement made easy
OI/TTH200-EN Rev. B 03.2019
—
TTH200 Introduction
The TTH200 with the 4 to 20 mA output and
HART communications protocol has global
approvals for explosion protection up to Zone 0.
Safety-relevant applications up to SIL 3
(redundant) are supported in accordance with
IEC 61508.
The TTH200 features a universal sensor input for
resistance thermometer, thermocouples,
resistance and voltage measurement.
Additional Information
Additional documentation on TTH200 is available for
download free of charge at
www.abb.com/temperature.
Alternatively simply scan this code:
—
We reserve the right to make technical changes or modify the contents of this document
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole
or in parts – is forbidden without prior written consent of ABB.
© ABB 2019 3KXT231002R4201

2 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
Table of contents
Change from one to two columns
1Safety.......................................................................... 3
General information and instructions.................................. 3
Warnings.................................................................................... 3
Intended use .............................................................................4
Improper use.............................................................................4
Warranty provisions.................................................................4
Notes on data safety ...............................................................4
Manufacturer’s address..........................................................4
2Use in potentially explosive atmospheres in
accordance with ATEX and IECEx ............................ 5
Ex marking.................................................................................5
Transmitter ..........................................................................5
LCD indicator .......................................................................5
Temperature data ....................................................................6
Transmitter ..........................................................................6
LCD indicator .......................................................................6
Electrical data ...........................................................................6
Transmitter ..........................................................................6
LCD indicator ....................................................................... 7
Installation instructions.......................................................... 7
ATEX / IECEx ........................................................................ 7
IP protection rating of housing ........................................ 7
Electrical connections ........................................................ 7
Grounding............................................................................. 7
Commissioning.........................................................................9
Operating instructions............................................................9
Protection against electrostatic discharges..................9
3Use in potentially explosive atmospheres in
accordance with FM and CSA ................................. 10
Ex marking...............................................................................10
Transmitter ........................................................................10
LCD indicator .....................................................................10
Installation instructions........................................................10
FM / CSA .............................................................................10
IP protection rating of housing ......................................10
Electrical connections ...................................................... 11
Commissioning....................................................................... 11
Operating instructions.......................................................... 11
Protection against electrostatic discharges................ 11
4Design and function ................................................ 12
General ..................................................................................... 12
5Product identification ............................................ 12
Name plate .............................................................................. 12
6Transport and storage............................................ 13
Inspection................................................................................ 13
Transporting the device........................................................ 13
Storing the device .................................................................. 13
Ambient conditions .......................................................... 13
Returning devices................................................................... 13
7Installation................................................................14
Installation options ............................................................... 14
Installation in the cover of the connection head ........ 14
Installation on the measuring inset............................... 14
Installation on the top-hat rail........................................ 14
Installing / removing the optional LCD indicator.............15
Disassembling the LCD indicator ...................................15
Installing the LCD indicator .............................................15
Rotating the LCD indicator ..............................................15
8Electrical connections .............................................15
Safety instructions .................................................................15
Protection of the transmitter from damage caused by
highly energetic electric interferences .............................. 16
Conductor material ............................................................... 16
Pin assignment........................................................................17
Electrical data for inputs and outputs............................... 18
Input - resistance thermometer / resistances ............ 18
Input - thermocouples / voltages.................................. 18
Output – HART®................................................................. 19
Power supply .......................................................................... 19
9Commissioning ....................................................... 20
General..................................................................................... 20
Checks prior to commissioning .......................................... 20
Communication ..................................................................... 20
Parameterization of the device............................................21
Parameter descriptions................................................... 22
Factory settings................................................................ 24
Basic Setup ............................................................................. 25
HART variables................................................................... 26
Communication / HART TAG / device addressing ..... 26
10Operation................................................................. 26
Safety instructions ................................................................ 26
Process display ...................................................................... 26
Error messages on the LCD display .............................. 27
11Diagnosis / error messages ...................................27
Possible error messages – HART® ...................................... 28
12Maintenance ............................................................ 29
Safety instructions ................................................................ 29
Cleaning................................................................................... 29
13Repair ....................................................................... 29
Safety instructions ................................................................ 29
Returning devices .................................................................. 29
14Recycling and disposal........................................... 30
15Specification ........................................................... 30
16Additional documents............................................ 30
17Appendix ...................................................................31
Return form..............................................................................31

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 3
1Safety
General information and instructions
These instructions are an important part of the product and
must be retained for future reference.
Installation, commissioning, and maintenance of the product
may only be performed by trained specialist personnel who have
been authorized by the plant operator accordingly. The specialist
personnel must have read and understood the manual and must
comply with its instructions.
For additional information or if specific problems occur that are
not discussed in these instructions, contact the manufacturer.
The content of these instructions is neither part of nor an
amendment to any previous or existing agreement, promise or
legal relationship.
Modifications and repairs to the product may only be performed
if expressly permitted by these instructions.
Information and symbols on the product must be observed.
These may not be removed and must be fully legible at all times.
The operating company must strictly observe the applicable
national regulations relating to the installation, function testing,
repair and maintenance of electrical products.
Warnings
The warnings in these instructions are structured as follows:
DANGER
The signal word ‘DANGER’ indicates an imminent danger.
Failure to observe this information will result in death or
severe injury.
WARNING
The signal word ‘WARNING’ indicates an imminent danger.
Failure to observe this information may result in death or
severe injury.
CAUTION
The signal word ‘CAUTION’ indicates an imminent danger.
Failure to observe this information may result in minor or
moderate injury.
NOTICE
The signal word
‘
NOTIC
E
’
indicates possible material damage.
Note
‘Note’ indicates useful or important information about the
product.

4 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 1 Safety
Intended use
This device is intended for the following uses:
• To measure the temperature of fluid, pulpy or pasty
substances and gases or resistance/voltage values.
The device has been designed for use exclusively within the
technical limit values indicated on the name plate and in the data
sheets.
• The maximum ambient temperature must not be exceeded.
• The IP rating of the housing must be observed during
operation.
• For use in potentially explosive atmospheres, follow the
associated guidelines.
• When using as a SIL-device in safety-relevant applications,
the SIL Safety Manual should be observed.
Improper use
The following are considered to be instances of especially
improper use of the device:
• Material application, for example by painting over the
housing, name plate or welding/soldering on parts.
• Material removal, for example by spot drilling the
housing.
Warranty provisions
Using the device in a manner that does not fall within the scope
of its intended use, disregarding this manual, using
underqualified personnel, or making unauthorized alterations
releases the manufacturer from liability for any resulting
damage. This renders the manufacturer's warranty null and void.
Notes on data safety
This product is designed to be connected to and to
communicate information and data via a network interface.
It is operator’s sole responsibility to provide and continuously
ensure a secure connection between the product and your
network or any other network (as the case may be).
Operator shall establish and maintain any appropriate measures
(such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data,
installation of anti-virus programs, etc.) to protect the product,
the network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and / or theft of data or information.
ABB Automation Products GmbH and its affiliates are not liable
for damages and / or losses related to such security breaches,
any unauthorized access, interference, intrusion, leakage and /
or theft of data or information.
Manufacturer’s address
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
Customer service center
Tel: [phone]
Email: [email protected]
Change from tw o to one column

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 5
2Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Change from one to two columns
Note
• Further information on the approval of devices for use in
potentially explosive atmospheres can be found in the
explosion protection test certificates (at
www.abb.com/temperature).
• Depending on the design, a specific marking in accordance
with ATEX or IECEx applies.
Ex marking
Transmitter
ATEX intrinsic safety
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 0, 1 and 2.
Model TTH200-E1
Type Examination Test Certificate PTB 05 ATEX 2017 X
II 1 G Ex ia IIC T6 Ga
II 2 (1) G Ex [ia IIC Ga] ib IIC T6 Gb
II 2 G (1D) Ex [ia IIIC Da] ib IIC T6 Gb
Non-sparking ATEX
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 2.
Model TTH200-E2
Declaration of conformity
II 3 G Ex nA IIC T1-T6 Gc
IECEx intrinsic safety
Approved for use in Zone 0, 1, and 2.
Model TTH200-H1
IECEx certificate of conformity IECEx PTB 09.0014X
Ex ia IIC T6...T1 Ga
Ex [ia IIC Ga] ib IIC T6...T1 Gb
Ex [ia IIIC Da] ib IIC T6...T1 Gb
LCD indicator
ATEX intrinsic safety
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 0, 1 and 2.
Type Examination Test Certificate PTB 05 ATEX 2079 X
II 1G Ex ia IIC T6 Ga
Non-sparking ATEX
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 2.
Declaration of conformity
II 3 G Ex nA IIC T1-T6 Gc
IECEx intrinsic safety
Approved for use in Zone 0, 1, and 2.
IECEx certificate of conformity IECEx PTB 12.0028X
Ex ia IIC T6

6 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Temperature data
Transmitter
ATEX / IECEx intrinsic safety
Temperature class Permissible ambient temperature range
Device category 1 use Device category 2 / 3 use
T6 −40 to 44 °C
(−40 to 111.2 °F)
−40 to 56 °C
(−40 to 132.8 °F)
T4-T1 −40 to 60 °C
(−40 to 140.0 °F)
−40 to 85 °C
(−40 to 185.0 °F)
ATEX Non-sparking
Temperature class Device category 3 use
T6 −40 to 56 °C (−40 to 132.8 °F)
T5 −40 to 71 °C (−40 to 159.8 °F)
T4 −40 to 85 °C (−40 to 185.0 °F)
LCD indicator
ATEX / IECEx intrinsic safety, ATEX non-sparking
Temperature class Permissible ambient temperature range
Device category 1 use Device category 2 / 3 use
T6 −40 to 44 °C
(−40 to 111.2 °F)
−40 to 56 °C
(−40 to 132.8 °F)
T5 −40 to 56 °C
(−40 to 132.8 °F)
−40 to 71 °C
(−40 to 159.8 °F)
T4-T1 −40 to 60 °C
(−40 to 140 °F)
−40 to 85 °C
(−40 to 185 °F)
Electrical data
Transmitter
Intrinsic safety type of protection Ex ia IIC (part 1)
Supply circuit
Max. voltage Ui= 30 V
Short-circuit current Ii= 130 mA
Max. power Pi= 0.8 W
Internal inductance Li= 160 µH*
Internal capacitance Ci= 0.57 nF**
* From HW-Rev. 1.12, previously Li= 0.5 mH.
** From HW-Rev. 1.07, previously Ci= 5 nF.
Intrinsic safety type of protection Ex ia IIC (part 2)
Thermocouples, voltages
Measurement circuit:
resistance thermometer,
resistances
Measurement circuit:
thermocouples, voltages
Max. voltage Uo= 6.5 V Uo= 1.2 V
Short-circuit current Io= 17.8 mA*Io= 50 mA
Max. power Po= 29 mW** Po= 60 mW
Internal inductance Li= 0 mH Li= 0 mH
Internal capacitance Ci= 118 nF*** Ci= 118 nF***
Maximum permissible
external inductance
Lo= 5 mH Lo= 5 mH
Maximum permissible
external capacitance
Co= 1.55 μFC
o= 1.05 μF
* From HW-Rev. 1.12, previously Io= 25 mA.
** From HW-Rev. 1.12, previously Po= 38 mW.
*** From HW-Rev. 1.12, previously Ci= 49 nF.
Intrinsic safety type of protection Ex ia IIC (part 3)
LCD indicator interface
Max. voltage Uo= 6.2 V
Short-circuit current Io= 65.2 mA
Max. power Po= 101 mW
Internal inductance Li= 0 mH
Internal capacitance Ci= 0 nF
Maximum permissible external
inductance
Lo= 5 mH
Maximum permissible external
capacitance
Co= 1.4 μF

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 7
LCD indicator
Intrinsic safety type of protection Ex ia IIC
Supply circuit
Max. voltage Ui= 9 V
Short-circuit current Ii= 65.2 mA
Max. power Pi= 101 mW
Internal inductance Li= 0 mH
Internal capacitance Ci= 0 nF
Installation instructions
ATEX / IECEx
The installation, commissioning, maintenance and repair of
devices in potentially explosive atmospheres must only be
carried out by appropriately trained personnel. Works may be
carried out only by persons, whose training has included
instructions on different types of protection and installation
techniques, concerned rules and regulations as well as general
principles of zoning. The person must possess the relevant
expertise for the type of works to be executed.
When operating with combustible dusts, EN 60079-31 must be
complied with.
The safety instructions for electrical apparatus in potentially
explosive areas must be complied with, in accordance with the
directive 2014/34/EU (ATEX) and e.g. IEC 60079-14 (Installation
of equipment in potentially explosive atmospheres).
To ensure safe operation, the respectively applicable
requirements must be met for the protection of workers.
IP protection rating of housing
The temperature transmitter and LCD display type AS must be
installed such that the IP rating of at least IP20 is achieved in
accordance with IEC 60529.
Electrical connections
Grounding
If, for functional reasons, the intrinsically safe circuit needs to be
grounded by means of a connection to the potential
equalization, it may only be grounded at one point.
Intrinsic safety installation check
If transmitters are operated in an intrinsically safe circuit, proof
that the interconnection is intrinsically safe must be provided in
accordance with IEC/EN 60079-14 as well as IEC/EN 60079-25.
The supply isolators / DCS inputs must feature intrinsically safe
input protection circuits in order to eliminate hazards (spark
formation).
In order to provide proof of intrinsic safety, the electrical limit
value must be used as the basis for the EC-type examination
certificates for the equipment (devices); this includes the
capacitance and inductance values of the cables.
Proof of intrinsic safety is said to have been provided if the
following conditions are fulfilled when a comparison is carried
out in relation to the limit values of the equipment:
Transmitter
(intrinsically safe equipment)
Supply isolator / DCS input
(related equipment)
Ui≥U
o
Ii≥I
o
Pi≥P
o
Li+ Lc(cable) ≤L
o
Ci+ Cc(cable) ≤C
o
Field (Ex area) Control room (safe area)
ATransmitter BSupply isolator / DCS input with
supply / Segment coupler
Figure 1: Intrinsic safety installation check
Installation in a potentially explosive atmosphere
Transmitters can be installed in all kinds of industrial sectors.
Potentially explosive systems are divided into zones,
meaning that a wide range of different instruments are also
required. For this, pay attention to the country-specific
guidelines and certificates!
Note
Ex relevant specifications must be taken from the EC-type
examination certificates and other relevant certificates that
apply in each case.

8 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
… Installation instructions
ATEX - Zone 0
Designation: II 1 G Ex ia IIC T6 Ga
Ex-area Zone 0 Safe area
ASensor
BTransmitter in housing with IP
rating IP 20
CSupply isolator [Ex ia]
DInterface for LCD indicator
Figure 2: Hookup in ATEX - Zone 0
When using the transmitter in Zone 0, it must be installed in a
suitable housing with IP -rating IP 20.
The input for the supply isolator must be designed with ‘Ex ia’
type of protection.
When using the transmitter in Zone 0, make sure that
impermissible electrostatic charging of the transmitter is
avoided (observe the warnings on the device).
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards.
Note
When operating the transmitter in Zone 0 (EPL ‘Ga’), the
compatibility of the device materials with the surrounding
atmosphere must be guaranteed.
Encapsulation material used for the transmitter:
Polyurethane (PUR), WEVO PU-417
ATEX - Zone 1 (0)
Marking: II 2 (1) G Ex [ia IIC Ga] ib IIC T6 Gb
Zone 0 or 1 Ex-area Zone 1 Safe area
ASensor
BTransmitter in housing with
IP-rating IP 20
CSupply isolator [Ex ib]
DInterface for LCD indicator
Figure 3: Hookup in ATEX - Zone 1 (0)
When using the transmitter in Zone 1, it must be installed in a
suited housing with IP rating IP 20.
The input of the supply isolator must be designed with ‘Ex ib’
type of protection.
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards. The sensor can be installed in Zone 1 or
Zone 0.
When using the transmitter in Zone 1, make sure that
impermissible electrostatic charging of the temperature
transmitter is avoided (observe the warnings on the device).

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 9
ATEX - Zone 1 (20)
Marking: II 2 G (1D) Ex [ia IIIC Da] ib IIC T6 Gb
Zone 20 or 21 Ex-area Zone 1 Safe area
ASensor
BTransmitter in housing with IP
rating IP 20
CSupply isolator [Ex ib]
DInterface for LCD indicator
Figure 4: Hookup in ATEX - Zone 1 (20)
When using the transmitter in Zone 1, it must be installed in a
suitable housing with IP -rating IP 20.
The input for the supply isolator must be designed with ‘Ex ib’
type of protection.
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards. The sensor can be installed in Zone 20 or
Zone 21.
When using the transmitter in Zone 1, make sure that
impermissible electrostatic charging of the temperature
transmitter is avoided (observe the warnings on the device).
ATEX - Zone 2
Designation: II 3 G Ex nA IIC T1-T6 Gc
Ex-area Zone 2 Safe area
ASensor
BTransmitter in housing with IP
rating IP 54
CSupply isolator
DInterface for LCD indicator
Figure 5: Hookup in ATEX - Zone 2
When using the transmitter in Zone 2, observe the following:
• The temperature transmitter must be installed in its own
housing. This housing must at least meet IP rating IP 54
(in accordance with EN 60529) and other requirements
for potentially explosive atmosphere (e.g. a certified
housing).
• External measures must be made for the power supply
circuit in order to prevent the rated voltage from being
up-scaled by more than 40 % in the event of transient
disturbances.
• The electrical connections must only be opened or closed
when there is no hazardous atmosphere.
• When using the transmitter in Zone 2, make sure that
impermissible electrostatic charging of the temperature
transmitter is prevented (observe the warnings on the
device).
Commissioning
The commissioning and parameterization of the device may also
be carried out in potentially explosive atmospheres using a
handheld terminal that has been approved accordingly under
consideration of an intrinsic safety installation check.
Alternatively, an Ex modem can be connected to the circuit
outside the potentially explosive atmosphere.
Operating instructions
Protection against electrostatic discharges
The plastic parts inside the device can store electrostatic
charges.
Make sure that no electrostatic charges can accumulate when
handling the device.
Change from tw o to one column

10 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
3Use in potentially explosive atmospheres in accordance with FM and CSA
Change from one to two columns
Note
• Further information on the approval of devices for use in
potentially explosive atmospheres can be found in the
explosion protection test certificates (at
www.abb.com/temperature).
• Depending on the design, a specific marking in accordance
with FM or CSA applies.
Ex marking
Transmitter
FM Intrinsically Safe
Model TTH200-L1
Control Drawing TTH200-L1H (I.S.)
Class I, Div. 1 + 2, Groups A, B, C, D
Class I, Zone 0, AEx ia IIC T6
FM Non-Incendive
Model TTH200-L2
Control Drawing TTH200-L2H (N.I.)
Class I, Div. 2, Groups A, B, C, D
CSA Intrinsically Safe
Model TTH200-R1
Control Drawing TTH200-R1H (I.S.)
Class I, Div. 1 + 2, Groups A, B, C, D
Class I, Zone 0, Ex ia Group IIC T6
CSA Non-Incendive
Model TTH200-R2
Control Drawing TTH200-R2H (1) (N.I.)
TTH200-R2H (2, no conduit) (N.I.)
Class I, Div. 2, Groups A, B, C, D
LCD indicator
FM Intrinsically Safe
Control Drawing SAP_214 748
I.S. Class I Div 1 and Div 2, Group: A, B, C, D or
I.S. Class I Zone 0 AEx ia IIC T*
Ui/ Vmax = 9 V, Ii/ Imax < 65.2 mA, Pi= 101 mW, Ci= 0.4 μF, Li= 0
FM Non-Incendive
Control Drawing SAP_214 751
N.I. Class I Div 2, Group: A, B, C, D oder Ex nL IIC T**, Class I Zone 2
Ui/ Vmax = 9 V, Ii/ Imax < 65.2 mA, Pi= 101 mW, Ci= 0.4 μF, Li= 0
CSA Intrinsically Safe
Control Drawing SAP_214 749
I.S. Class I Div 1 and Div 2; Group: A, B, C, D or
I.S Zone 0 Ex ia IIC T*
Ui/ Vmax = 9 V, Ii/ Imax < 65.2 mA, Pi= 101 mW, Ci< 0.4 μF, Li= 0
CSA Non-Incendive
Control Drawing SAP_214 750
N.I. Class I Div 2, Group: A, B, C, D oder Ex nL IIC T**, Class I Zone 2
Ui/ Vmax = 9 V, Ii/ Imax < 65.2 mA, Pi= 101 mW, Ci< 0.4 μF, Li= 0
* Temp. Ident: T6 Tamb 56 °C, T4 Tamb 85 °C
** Temp. Ident: T6 Tamb 60 °C, T4 Tamb 85 °C
Installation instructions
FM / CSA
The installation, commissioning, maintenance and repair of
devices in areas with explosion hazard must only be carried out
by appropriately trained personnel.
The operator must strictly observe the applicable national
regulations with regard to installation, function tests, repairs,
and maintenance of electrical devices. (e. g. NEC, CEC).
IP protection rating of housing
The temperature transmitter and LCD display type AS must be
installed such that the IP rating of at least IP20 is achieved in
accordance with IEC 60529.

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 11
Electrical connections
Grounding
If, for functional reasons, the intrinsically safe circuit needs to be
grounded by means of a connection to the potential
equalization, it may only be grounded at one point.
Intrinsic safety installation check
If transmitters are operated in an intrinsically safe circuit, proof
that the interconnection is intrinsically safe must be provided in
accordance with IEC/EN 60079-14 as well as IEC/EN 60079-25.
The supply isolators / DCS inputs must feature intrinsically safe
input protection circuits in order to eliminate hazards (spark
formation).
In order to provide proof of intrinsic safety, the electrical limit
value must be used as the basis for the EC-type examination
certificates for the equipment (devices); this includes the
capacitance and inductance values of the cables.
Proof of intrinsic safety is said to have been provided if the
following conditions are fulfilled when a comparison is carried
out in relation to the limit values of the equipment:
Transmitter
(intrinsically safe equipment)
Supply isolator / DCS input
(related equipment)
Ui≥U
o
Ii≥I
o
Pi≥P
o
Li+ Lc(cable) ≤L
o
Ci+ Cc(cable) ≤C
o
Field (Ex area) Control room (safe area)
ATransmitter BSupply isolator / DCS input with
supply / segment coupler
Figure 6: Intrinsic safety installation check
Installation in a potentially explosive atmosphere
Transmitters can be installed in all kinds of industrial sectors.
Potentially explosive systems are divided into zones,
meaning that a wide range of different instruments are also
required. For this, pay attention to the country-specific
guidelines and certificates!
Note
Ex relevant specifications must be taken from the EC-type
examination certificates and other relevant certificates that
apply in each case.
Commissioning
The commissioning and parameterization of the device may also
be carried out in potentially explosive atmospheres using a
handheld terminal that has been approved accordingly under
consideration of an intrinsic safety installation check.
Alternatively, an Ex modem can be connected to the circuit
outside the potentially explosive atmosphere.
Operating instructions
Protection against electrostatic discharges
The plastic parts inside the device can store electrostatic
charges.
Make sure that no electrostatic charges can accumulate when
handling the device.

12 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
4Design and function
General
Digital transmitters are communication-ready devices with
microprocessor-controlled electronics. They conform to the
requirements of IP rating IP 20 and are suited for integration
into DIN A and DIN B sensor heads.
In the HART® transmitter, an FSK signal is superimposed on the
4 to 20 mA output signal in accordance with the HART standard
to facilitate bidirectional communication.
The transmitters can be configured, polled, and tested using a
DTM, an EDD or using the Field Information Manager (FIM).
Handheld terminals can also be used for communication
purposes.
As an option, the transmitter can be fitted with a type AS LCD
display. The LCD display is used exclusively for visualizing
current process values. The electrical connection between the
LCD display and transmitter is provided by a 6-pin flat ribbon
cable with a plug connector. The LCD display can only be
operated when connected to transmitters that have an LCD
display interface.
Note
The HMI type A LCD indicator with configuration function
optionally used with the TTH300 is not compatible with the
TTH200.
5Product identification
Name plate
Note
Products that are marked with the adjacent symbol
may not be disposed of as unsorted municipal waste
(domestic waste).
They should be disposed of through separate
collection of electric and electronic devices.
Note
The ambient temperature range
n provided on the name plate
refers only to the transmitter itself and not to the sensor
element used in the measuring inset.
1Manufacturer, manufacturer address, manufacturing year - week
2Safety integrity level, SIL logo (optional with HART transmitter)
3CE mark (EU conformity), if not on additional plate
4Type designation / model
5Transmitter communications protocol (HART)
62D barcode for serial number in accordance with order
77-digit serial number of the device electronic unit
8Software revision
9Hardware version
j‘Follow product documentation’ symbol
kSet measuring range of the transmitter
lMeasuring point tag (TAG) in accordance with order (optional)
mSet sensor type and circuit type
nAmbient temperature range, on additional plate for Ex versions
oTransmitter specification (supply voltage range, output current range,
communications protocol)
pCoding of the type of protection of the device (in accordance with
ordering information)
qSerial number of the device (serial number in accordance with order)
Figure 7: Name plate (example)

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 13
Devices with an explosion-proof design are marked with the
following special data plate.
1Type designation in accordance
with approval
2Type designation
3Temperature class of the
explosion-proof design
4CE mark (EU conformity) and
notified body for quality
assurance
5Ex marking
6IP rating explosion-proof design
Figure 8: Additional plate for explosion-protected apparatus (example)
Note
The name plates displayed are examples. The device
identification plates affixed to the device can differ from this
representation.
6Transport and storage
Inspection
Check the devices immediately after unpacking for possible
damage that may have occurred from improper transport.
Details of any damage that has occurred in transit must be
recorded on the transport documents.
All claims for damages must be submitted to the shipper
without delay and before installation.
Transporting the device
Observe the following instructions:
• Do not expose the device to humidity during transport.
Pack the device accordingly.
• Pack the device so that it is protected against vibrations
during transport, for example, by using air-cushioned
packing.
Storing the device
Bear the following points in mind when storing devices:
• Store the device in its original packaging in a dry and
dust-free location.
• Observe the permitted ambient conditions for transport
and storage.
• Avoid storing the device in direct sunlight.
• In principle, the devices may be stored for an unlimited
period. However, the warranty conditions stipulated in
the order confirmation of the supplier apply.
Ambient conditions
The ambient conditions for the transport and storage of the
device correspond to the ambient conditions for operation of
the device.
Adhere to the device data sheet!
Returning devices
For the return of devices, follow the instructions in Repair on
page 29.

14 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
7Installation
Installation options
There are three options for installing the transmitter:
• Installation in the cover of the connection head
(without springs)
• Direct installation on the measuring inset (with springs)
• Installation on a top-hat rail
Installation in the cover of the connection head
1
2
3
A10067
Figure 9: Installation example
1.Release the screw plug 3for the cover of the connection
head.
2.Open the cover 1.
3.Secure the transmitter 2at the proper position on the
cover, using the captive screws found in the transmitter.
Installation on the measuring inset
A10066
1
2
3
4
Figure 10: Installation example
Note
Before mounting the transmitter on the measuring inset, remove
the ceramic block on the measuring inset and the captive screws
in the transmitter.
To install the transmitter on the measuring inset, cambered
toothed discs and the corresponding mounting screws are
required; these must be ordered as separate accessories:
Measuring inset installation set (2 fixing screws, 2 springs,
2 toothed discs) order number: 263750
1.Remove the ceramic block from the measuring inset 3.
2.Remove the screws from the transmitter 2. Remove the
sleeves from the screw holes and then remove the screws.
3.Insert new fixing screws 1from above in the fixing holes of
the transmitter.
4.Place the cambered toothed discs 4with curve facing
upward on the downward protruding screw thread.
5.Connect the power supply cable to the transmitter according
to connection diagram.
6.Place the transmitter in the housing on the measuring inset
and secure it.
Note
The toothed discs between measuring inset and transmitter are
straightened when the screws are tightened. This enables them
to grip the mounting screws.
Installation on the top-hat rail
A10103
Figure 11: Installation example
When mounted on a top-hat rail, the transmitter can be placed at
a distance from the sensor in a housing that is suitable for the
ambient conditions.

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 15
Installing / removing the optional LCD
indicator
The transmitter can be optionally equipped with an LCD
indicator.
NOTICE
Damage to the LCD indicator caused by incorrect installation
/ disassembly
The flat ribbon cable of the LCD indicator can become
damaged due to incorrect installation / disassembly.
• Make sure the flat ribbon cable does not get twisted or
torn when installing / disassembling or rotating the LCD
indicator.
Disassembling the LCD indicator
The indicator must be removed to enable connection of the
sensor line or supply line:
Carefully remove the LCD indicator from the transmitter
inset. The LCD indicator is held firmly in place, meaning that
you may have to use the tip of a screwdriver to pry it loose.
Take care to avoid any mechanical damage.
Installing the LCD indicator
No tools are required to install the LCD indicator.
1.Carefully insert the guide pins for the LCD indicator in the
guide holes of the transmitter inset. Make sure the black
connection socket fits into the terminal on the transmitter
inset.
2.Then press the LCD indicator in as far as it will go. Make sure
that the guide pins and connection socket are fully inserted.
Rotating the LCD indicator
The position of the LCD indicator can be adjusted to suit the
mounting position of the transmitter, to ensure that the display
is as clearly legible as possible.
There are twelve positions at increments of 30°.
1.Carefully turn the LCD indicator to the left to release it from
its holder.
2.Carefully turn the LCD indicator until the required position is
reached.
3.Insert the LCD indicator into its holder again and turn it to
the right into the required position until it snaps into place.
8Electrical connections
Safety instructions
DANGER
Improper installation and commissioning of the device
carries a risk of explosion.
For use in potentially explosive atmospheres, observe the
information in Use in potentially explosive atmospheres in
accordance with ATEX and IECEx on page 5 and Use in
potentially explosive atmospheres in accordance with FM
and CSA on page 10!
Observe the following instructions:
• The electrical connection may only be established by
authorized specialist personnel and in accordance with
the connection diagrams.
• The relevant regulations must be observed during electric
installation.
• The electrical connection information in the instruction
must be observed; otherwise, the electric IP rating may
be adversely affected.
• Safe isolation of electric circuits which are dangerous if
touched is ensured only if the connected devices satisfy
the requirements of DIN EN 61140 (VDE 0140 Part 1)
(basic requirements for safe isolation).
• To ensure safe isolation, install connection leads separate
from electric circuits which are dangerous if touched, or
implement additional insulation measures.
• Connections must only be established in a dead-voltage
state!
• The transmitter has no switch-off elements. Therefore,
overcurrent protective devices, lightning protection, or
voltage disconnection options must be provided with the
installation.
• The power supply and signal are routed in the same
conductor and should be implemented as a SELV or PELV
circuit in accordance with the relevant standard
(standard version). For the explosion-proof design, the
guidelines in accordance with the Ex standard must be
adhered to.
• You need to check that the available power supply
corresponds to the information on the name plate.
Note
The signal cable wires must be provided with wire end sleeves.
The slotted screws of the connection terminals are tightened
with a size 1 screwdriver (3.5 or 4 mm).

16 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 8 Electrical connections
Protection of the transmitter from damage
caused by highly energetic electric
interferences
The transmitter has no switch-off elements. Therefore,
overcurrent protective devices, lightning protection, or voltage
disconnection options must be provided at the plant.
For the shielding and grounding of the device and the
connection cable, observe Pin assignment on page 17.
NOTICE
Temperature transmitter damage!
Overvoltage, overcurrent and high-frequency interference
signals on the supply connection as well as sensor connection
side of the device can damage the temperature transmitter.
ADo not weld
BNo high-frequency interference signals / switching operations of large
consumers
CNo overvoltage due to lightning
Figure 12: Warning signs
Overcurrent and overvoltage can occur through for example
welding operations, switching operations of large electric
consumers, or lightning in the vicinity of the transmitter, sensor,
as well as connector cables.
Temperature transmitters are sensitive devices on the sensor
side as well. Long connector cables to the sensor can encourage
damaging interference. This can already happen if temperature
sensors are connected to the transmitter during installation, but
are not yet integrated into the system (no connection to the
supply isolator / DCS)!
Suited protective measures
The following items should be observed to protect the
transmitter from sensor-side damage:
• In the vicinity of the transmitter, sensor and sensor
connector cable in case of a connected sensor, high-energy
overvoltage, overcurrent and high-frequency interference
signals due to welding operations, lightning, circuit breakers
or large consumers of electricity among others should be
absolutely avoided.
• The connection cable of the sensor on the transmitter should
be disconnected when performing welding work in the
vicinity of the installed transmitter, sensor, as well as supply
lines from the sensor to the transmitter.
• This correspondingly also applies to the supply side, if there
is a connection there.
Conductor material
NOTICE
Danger of wire break!
The use of stiff cable material can lead to wire breaks in the
cables.
• Only use cable material with stranded wires.
Supply voltage
Power supply cable:
Flexible standard cable material
Maximum wire cross section:
1.5 mm2(AWG 16)
Sensor connection
Depending on the type of sensor, a variety of cable materials can
be used for connections.
The integrated internal reference junction makes it possible to
directly connect thermal compensating cables.
Change from tw o to one column

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 17
Pin assignment
APotentiometer, four-wire circuit
BPotentiometer, three-wire circuit
CPotentiometer, two-wire circuit
DRTD, four-wire circuit
ERTD, three-wire circuit
FRTD, two-wire circuit
GVoltage measurement
HThermocouple
IInterface for type AS LCD indicator
1to 4Sensor connection (of measuring inset)
5to 64 to 20 mA HART
Figure 13: TTH200 connections
Change from one to two columns

18 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 8 Electrical connections
Electrical data for inputs and outputs
Input - resistance thermometer / resistances
Resistance thermometer
• Pt100 in accordance with IEC 60751, JIS C1604, MIL-T-24388
• Ni in accordance with DIN 43760
• Cu in accordance with recommendation OIML R 84
Resistance measurement
• 0 to 500 Ω
• 0 to 5000 Ω
Sensor connection type
Two-, three-, four-wire circuit
Connection lead
• Maximum sensor line resistance
per line 50 Ωin accordance with NE 89
• Three-wire circuit:
Symmetrical sensor line resistances
• Two-wire circuit:
Compensation up to 100 Ωtotal lead resistance
Measurement current
< 300 μA
Sensor short circuit
< 5 Ω(for resistance thermometer)
Sensor wire break
• Measuring range: 0 to 500 Ω> 0.6 to 10 kΩ
• Measuring range: 0 to 5 Ω> 5.3 to 10 kΩ
Corrosion detection in accordance with NE 89
• Three-wire resistance measurement > 50 Ω
• Four-wire resistance measurement > 50 Ω
Sensor error signaling
• Resistance thermometer:
Sensor short circuit and sensor wire break
• Linear resistance measurement:
Sensor wire break
Input - thermocouples / voltages
Types
• B, E, J, K, N, R, S, T in accordance with IEC 60584
• U, L in accordance with DIN 43710
• C, D in accordance with ASTM E-988
Voltages
• −125 to 125 mV
• −125 to 1100 mV
Connection lead
• Maximum sensor line resistance:
per line 1.5 kΩ, total 3 kΩ
Sensor wire break monitoring in accordance with NE 89
• Pulsed with 1 µA outside measurement interval
• Thermocouple measurement 5.3 to 10 kΩ
• Voltage measurement 5.3 to 10 kΩ
Input resistance
> 10 MΩ
Internal reference junction Pt1000, IEC 60751 Cl. B
(no additional jumpers necessary)
Sensor error signaling
• Thermocouple:
Sensor wire break
• Linear voltage measurement:
Sensor wire break

TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B 19
Output – HART®
Note
The HART® protocol is an unsecured protocol, as such the
intended application should be assessed to ensure that these
protocols are suitable before implementation.
Transmission characteristics
• Temperature linear
• Resistance linear
• Voltage linear
Output signal
• Configurable 4 to 20 mA (standard)
• Configurable 20 to 4 mA
(Dynamic range: 3.8 to 20.5 mA in accordance with NE 43)
Simulation mode
3.5 to 23.6 mA
Induced current consumption
< 3.5 mA
Maximum output current
23.6 mA
Configurable error current signal
• Overrange 22 mA (20.0 to 23.6 mA)
• Underrange 3.6 mA (3.5 to 4.0 mA)
Power supply
Two-wire technology, polarity safe; power supply lines = signal
lines
Note
Following calculations apply for standard applications. This
should be taken into consideration when working with a higher
maximum current.
Input terminal voltage
Non-Ex application:
US= 11 to 42 V DC
Ex applications:
US= 11 to 30 V DC
Maximum permissible residual ripple for input terminal
voltage
During communication, this is in accordance with the HART® FSK
‘Physical Layer’ specification.
Undervoltage detection on the transmitter
If the terminal voltage on the transmitter down-scales a value of
10 V, this may lead to an output current of Ia≤3.6 mA.
Maximum load
RB= (US−11 V) / 0.022 A
A TTH200
BTTH200 in Ex-applications
CHART® communication resistance (RB)
Figure 14: Maximum load depending on input terminal voltage
Maximum power
• P = Us× 0.022 A
• Example: Us= 24 V Pmax = 0.528 W

20 TTH200 HEAD-MOUNT TEMPERATURE TRANSMITTER | OI/TTH200-EN REV. B
… 8 Electrical connections
… Power supply
Voltage drop on the signal line
When connecting the devices, note the voltage drop on the
signal line. The minimum supply voltage on the transmitter must
not be undershot.
A11122
AB
+
-
U1
+
U2
-
R
R250
ATransmitter BSupply isolator / DCS input with
supply / segment coupler
Figure 15: HART load resistance
U1min: Minimum supply voltage on the transmitter
U2min: Minimum supply voltage of the supply isolator /
DCS input
R: Line resistance between transmitter and supply isolator
R250: Resistance (250 Ω) for HART functionality
Standard application with 4 to 20 mA functionality
When connecting these components, observe the following
condition:
U1min ≤U2min - 22 mA × R
Standard application with HART functionality
Adding resistance R250 increases the minimum supply voltage
U2min: U1min ≤U2min - 22 mA × (R + R250)
For HART functionality, use supply isolators or DCS input cards
with a HART mark. If this is not possible, a resistance of ≥250 Ω
(< 1100 Ω) must be added to the interconnection.
The signal line can be operated with / without grounding. When
establishing a ground connection (minus side), make sure that
only one side of the terminal is connected to the equipotential
bonding.
9Commissioning
General
In case of corresponding order the transmitter is ready for
operation after mounting and installation of the connections.
The parameters are set at the factory.
The connected lines must be checked for firm seating. Only
firmly seated lines ensure full functionality.
Checks prior to commissioning
The following points must be checked before commissioning the
device:
• Correct wiring in accordance with Electrical connections
on page 15.
• The ambient conditions must correspond to the
information given on the name plate and in the data
sheet.
Communication
Note
The HART® protocol is an unsecured protocol, as such the
intended application should be assessed to ensure that these
protocols are suitable before implementation.
Communication with the transmitter takes place using the HART
protocol. The communication signal is modulated onto both
wires of the signal line in accordance with the HART FSK ‘Physical
Layer’ specification.
The HART modem is connected at the signal line of the current
output via which power is also supplied via the power supply
unit.