Abus IPCB42501 User manual

IPCB42501 / IPCB42551
Installation manual
Version 03/2017
English translation of the original German user manual. Retain for future reference.
IPCB42501
IPCB42551

13
Introduction
Dear Customer,
Thank you for purchasing this product.
This device complies with the requirements of the following EU directives: the EMC
Directive (2014/30/EU), the R&TTE Directive (2014/53/EU) and the RoHS Directive
(2011/65/EU).The declaration of conformity can be obtained from:
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
GERMANY
To ensure this condition is maintained and that safe operation is guaranteed, it is your obligation
to observe this user manual.
Please read the entire user manual carefully before putting the product into operation, and pay
attention to all operating instructions and safety information.
All company names and product descriptions are trademarks of the corresponding owner.
All rights reserved.
If you have any questions, please contact your specialist installation contractor or
specialist dealer.
Disclaimer
This user manual has been produced with the greatest of care. Should you discover any
missing information or inaccuracies, please let us know about them.
ABUS Security-Center GmbH & Co. KG does not accept any liability for technical and
typographical errors, and reserves the right to make changes to the product and user manuals
at any time and without prior warning.
ABUS Security-Center GmbH is not liable or responsible for any direct or indirect damage
resulting from the installation, performance and use of this product. No guarantee is made for
the contents of this document.

14
Important safety information
All guarantee claims are invalid in the event of damage caused by non-compliance
with this user manual. We cannot be held liable for resulting damage.
We cannot be held liable for material or personal damage caused by improper
operation or non-compliance with the safety information. All guarantee claims are
void in such cases.
Dear Customer,
The following safety information and hazard notes are not only intended to protect your health but
also to protect the device from damage. Please read the following points carefully:
There are no components inside the product that require maintenance by the operator. Opening or
dismantling the product invalidates the CE certification and guarantee claims/warranty.
The product may be damaged if it is dropped, even from a low height.
Avoid the following adverse conditions during operation:
Moisture or excess humidity
Extreme heat or cold
Direct sunlight
Dust or flammable gases, vapours or solvents
Strong vibrations
Strong magnetic fields (e.g. next to machines or loudspeakers)
The camera must not be installed on unstable surfaces.
General safety information:
Do not leave packaging material lying around. Plastic bags, sheeting, polystyrene packaging, etc.
can pose a danger to children if played with.
The video surveillance camera contains small parts which could be swallowed and must be kept
out of the reach of children for safety reasons.
Do not insert any objects into the device through the openings.
Only use replacement devices and accessories that are approved by the manufacturer. Do not
connect any non-compatible products.
Please pay attention to the safety information and user manuals for the other connected devices.
Check the device for damage before putting it into operation. Do not put the device into operation if
you identify any damage.
Adhere to the normal voltage limits specified in the technical data. Higher voltages could destroy
the device and pose a health risk (electric shock).
When installing the device in an existing video surveillance system, ensure that all devices
have been disconnected from the mains power circuit and low-voltage circuit.
If in doubt, have a specialist technician carry out assembly, installation and connection of the
device. Improper or unprofessional work on the power supply system or domestic installation
puts both you and other persons at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run
separately
from each other. They should not be connected at any point or become connected as a
result of a malfunction.

15
Contents
1. INTENDED USE................................................................................................................... 16
2. EXPLANATION OF SYMBOLS ........................................................................................... 16
3. CONNECTIONS AND FUNCTIONS..................................................................................... 17
3.1 POWER SUPPLY .................................................................................................................... 17
3.2 CALL FACTORY DEFAULT SETTINGS (RESET) .......................................................................... 17
3.3 SWITCHING INPUT/OUTPUT .................................................................................................... 17
3.4 AUDIO OUTPUT ..................................................................................................................... 18
3.5 WPS FUNCTION.................................................................................................................... 18
3.6 SD CARD SLOT ..................................................................................................................... 18
3.7 NOTES TO THE USAGE OF INTERNAL IR LEDS........................................................................ 19
4. MAINTENANCE AND CLEANING....................................................................................... 20
4.1 FUNCTION TEST .................................................................................................................... 20
4.2 CLEANING ............................................................................................................................ 20
5. DISPOSAL ........................................................................................................................... 20


16
1. Intended use
This camera is used for indoor and outdoor video surveillance (depending on the model) in
conjunction with a recording device or appropriate display unit (e.g. PC).
Use of this product for any other purpose than that described may lead to damage
to the product and other hazards. All other uses are not as intended and will result
in the invalidation of the product guarantee and warranty. No liability can be
accepted as a result. This also applies to any alterations or modifications made to
the product.
Read the user guide carefully and in full
before putting the product into operation. The user guide contains
important information on installation and operation.
2. Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of
injury or health hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in this user manual which
must be observed.
This symbol indicates special tips and notes on the operation of the device.
This user manual describes the software functions in the
camera browser interface. For information about how to
install the hardware for the respective camera, please read
the quick start manual or the hardware installation manual, if
you have it.
You can download a PDF version of the user manuals in your
language at www.abus.com via the product search.

17
3. Connections and functions
3.1 Power supply
ATTENTION!
Before you begin the installation, make sure that the supply voltage and the nominal
voltage of the camera match.
12 VDC, round plug, 5,5 x 2,1 mm
3.2 Call factory default settings (Reset)
1. Please disconnect the camera form power connection.
2. Press the "Reset" button on the camera and keep it pressed.
3. Now connect the power supply to the camera (2-pin power supply or Power over
Ethernet), and hold the "Reset" button pressed for another 30 seconds.
3.3 Switching input/output (only IPCB42551)
The maximum load values must be observed, otherwise, the camera may be
irreparably damaged.
Description Connection information
Switching input „I“ Bridge between „Alarm In“ and „GND“
„GND“
Switching output „O“ 5 VDC ~12 V DC, max. 30 mA, please note the connection
polarity
„GND“

18
3.4 Audio output (only IPCB42551)
Description Connection information
Audio output „A“ Impedance: 600 Ω
Frequency range: 20 Hz – 20 kHz
Output power: 20 mW @ 16 Ω
„GND“
3.5 WPS function (only IPCB42551)
1. Activate the WPS function on the router.
2. Then press the WPS button (within 120 seconds) (labeled "RST / WPS") for approximately
2 seconds.
3.6 SD card slot
To install the Micro SD card the cover and the dome bubble need to be removed first. The Micro-
SD card slot is located on the back of the camera.
Max. SD card size: 128 GByte
Before usage of micro SD card the card must be formatted.

19
3.7 Notes to the usage of internal IR LEDs
The IR range is strongly dependent on the environmental conditions. If the area in the
camera's field of view reflects poorly or if there are no objects within the max.
illumination range, the brightness of the video image at night may be too low. This will
result in poor usability of the video image.
In addition, when installing the camera it must be ensured that no objects are located in
close proximity to the camera's field of view (e.g. roof gutter or wall). These objects can
reflect back the IR light, resulting in circular fading on the video image in the opposite
direction to the object.
The IR range might be reduced as well by strong absorbing surfaces (e.g. asphalt).

20
4. Maintenance and cleaning
4.1 Function test
Regularly check the technical safety of the product, e.g. check the housing for damage.
If it appears to no longer be possible to operate the product safely, stop using it and secure it to
prevent unintentional use.
It is likely that safe operation is no longer possible in the event that:
the device shows signs of visible damage
the device no longer works correctly
the device has been stored in adverse conditions for a long period of time
the device has been exposed to stresses during transportation.
Please note:
You do not need to perform any maintenance on the product. There are no
components requiring servicing or checking inside the product. Never open it.
4.2 Cleaning
Clean the product with a clean, dry cloth. The cloth can be dampened with lukewarm water to
remove stubborn dirt.
Make sure that no liquids enter the inside of the device, as this
will destroy it. Do not use any chemical cleaning agents, as these could
damage the surface of the housing.
5. Disposal
Devices displaying this symbol may not be disposed of with domestic waste. At
the end of its service life, dispose of the product according to the applicable legal
requirements.
Please contact your dealer or dispose of the products at the local collection point
for electronic waste.