Acnodes PC 6170 User manual

PC 6170
17” Pentium-M PANEL PC
User’s Manual

Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. Acnodes Co.,
Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
Acnodes assumes no responsibility for any inaccuracies that may be contained in this
document. Acnodes makes no commitment
to update or to keep current the
information contained in
this manual.
Acnodes reserves the right to make improvements to this document and/or
product
at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in
any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise,
without the prior written permission of Acnodes Co., Ltd.
© Copyright 2005 by Acnodes Co., Ltd.
All rights reser ved.
April 2005, Version A1
ii

‹ CE Marking
‹ FCC Class A
Safety Approvals
FCC Compliance
This equipment has been tested and complies with the limits for a
Class
A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If
not installed and used in
accordance with
proper instructions, this equipment might generate or
radiate
radio frequency energy and cause harmful interference to
radio
communications. However, there is no guarantee that
interference will not occur
in a particular installation. If this equipment
does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded
interface cables must be used in order to comply with
emission limits.ou
iii

Safety Precautions
Before getting started, read the following important cautions.
1. The PC 6170 does not come equipped with an operating
system. An
operating system must be loaded first before
installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when
installing the
internal components. Use a grounding wrist strap
and
place all electronic components in any static-shielded
devices. Most electronic components
are sensitive to static
electrical charge.
3. Disconnect the power cord from the PC 6170 before making
any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could
ruin sensitive components. Make sure the
PC 6170 is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However,
hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the
system using
a cloth only. Do not spray any liquid cleaner
directly onto
the screen. The PC 6170 may come with or w/o a
touch screen. Although the touch screen is chemical resistant,
it is recommended that
you spray the liquid cleaner on a cloth
first before
wiping the screen. In case your system comes
without the touch screen, you must follow the same
procedure and not
spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touch screen.
Scratches
on the touch screen may cause malfunction or
internal failure to the
touch screen.
7. The flat panel display is not susceptible to shock or vibration.
When
assembling the PC 6170, make sure it is securely
installed.
iv

5. Do not open the system’s back cover. If opening the cover for
maintenance
is a must, only a trained technician is allowed to do
so. Integrated
circuits on computer boards are sensitive to static
electricity.
To avoid damaging chips from electrostatic discharge,
observe the following
precautions:
9 Before handling a board or integrated circuit, touch an
unpainted portion
of the system unit chassis for a few
seconds. This will
help to discharge any static electricity
on your body.
9 When handling boards and components, wear a
wrist-grounding
strap, available from most electronic
component stores.
Trademarks Acknow ledgments
Acnodes is a trademark of Acnodes Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics
Corporation.
Other brand names and trademarks are the properties of
their respective owners.
v

This page does not contain any information.
vi

Table of Contents
Chapter 1 Introduction ------------------------------- 1
1.1 General Description ........................................... 1
1.2 Specifications .................................................... 2
1.3 Dimensions ........................................................ 5
1.4 Front View and I/O Outlets ................................ 6
1.4.1 Front Vi ew .............................................................. 6
1.4.2 I/O Outl et ............................................................... 7
1.5 Package list........................................................ 8
Chapter 2 Hardware Installatioin ----------------- 9
2.1 CPU and DRAM Installation ............................... 9
2.2 HDD Installation ............................................... 11
2.3 CD-ROM Installation ........................................ 13
2.4 Add-on Card Installation ................................. 15
2.5 3 x Serial Ports ................................................ 16
2.6 Parallel Port ..................................................... 16
2.7 VGA .................................................................. 16
2.8 Ethernet............................................................ 17
2.9 Mountings: Panel/Wall/Desktop/VESA/Rack ... 18
2.9.1 VESA -A RM ............................................................. 18
2.9.2 Wall Mount ............................................................ 19
2.9.3 Desktop Ki t Assembl y............................................ 21
2.9.4 Panel -mount Kit A ssembly .................................... 23
2.9.5 Rack mounti ng A ssembl y ..................................... 24
Chapter 3 Driver Installation --------------------- 25
3.1 System ............................................................. 25
3.2 Touch Screen ................................................... 26
3.2.1 Speci fi cation ........................................................ 26
Table of Contents vii

3.2.2 Driver Installation- Wi ndows
98/2000/XP/CE.NET/XP-Embedded ...................... 27
3.2.3 Driver Installati on- DOS ......................................... 29
3.2.4 Driver Installati on- Li nux ........................................ 31
3.3 Dual LAN .......................................................... 33
Chapter 4 Embedded O.S. Installation -------- 35
4.1 Windows XP Embedded ................................... 35
4.1.1 Penmount Touch Screen ...................................... 35
4.2 Windows CE.NET 4.2 ....................................... 36
4.2.1 Calibrati on Touch Screen ..................................... 36
Appendix A SB83810 BIOS Setup -------------- 37
A.1 Standard CMOS Setup Menu ........................... 37
A.2 Advanced BIOS Features ................................. 40
A.3 Advanced Chipset Features ............................ 45
A.4 Integrated Peripherals ..................................... 47
A.5 Power Management Setup ............................... 52
A.6 PnP/PCI Configuration Setup .......................... 57
A.7 PC Health Status .............................................. 59
A.8 Frequency/Voltage Control.............................. 60
A.9 Load Fail-Safe Defaults ................................... 61
A.10 Load Optimized Defaults ................................. 62
Appendix B Power Supply Specification ----- 63
viii
Table of Contents

PC 6170 User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detail
specifications
of the PC 6170. Chapter 1 includes the following
sections:
„ General Description
„ System Specification
„ Dimensions
„ Front View & I/O Outlets
„ Package List
1.1 General Description
The PC 6170 is an ultra slim Panel PC which equipped with superior
Pentium® M processor and 17" SXGA LCD display. PC 6170
has friendly user interface design of using front access USB, may
let the customers easily connect keyboard/mouse and USB storage
device. In addition,
with P-M CPU and the advanced radiation design,
PANEL1170-810 has better stability and the ultra slim overhead
construction. The Back Door design also makes PC 6170 to be
extremely
easy to maintain.
Front Access USB Ports & OSD
To enhance the system for easy maintenance and upgrade, the two
front USB ports have been build-in to the front panel. By connecting
the
USB storage devices to the front USB ports, users can upgrade or
maintain the
software without dismount the panel PC from the rack.
The
OSD control keypads allows the users to tune the display
brightness and position at
front panel which ensures the users always
get
the best display condition for any specific application.
Most Reliable and Stable Design-Intel® Pentium® M
Processor
The Pentium®-M processor delivers outstanding computing
performance and low-power enhancements. Therefore, with the
remarkable radiation design and using P-M CPU, PC 6170 is
Introduction 1

PC 6170 User’s Manual
a high stability and high reliable Panel PC. At the same time, with the
Ultra Slim case design, customers can easily install PANEL1170-810
everywhere.
Easy-to-Maintenance Design: Back Door
The back panel of the PC 6170 was anchored by hand-
removable fasten screws. Users can install the CPU, Memory, and
HDD
without using screw driver to open the main cabinet. This
modular
design helps to minimize system down-time for maintenance.
The two front accessible USB ports also enable the easy connection
of input devices such as Keyboard or Mouse. By connecting to USB
FDD,
CD-ROM, or Memory Stick, users can update the newest
software to the system or download the system information to memory
devices.
1.2 Specifications
Main CPU board
„ CPU: Intel
®
Pentium
®
M up 1.8GHz
„ System Chipset: Intel
®
855GME/6300ESB
„ BIOS: Phoenix-Award BIOS, Y2K compliant 4Mbit Flash,
DMI,
Plug and Play SmartView for multiple LCD
type selection,
display mode option and
application extension features RPL/PXE
Ethernet
Boot ROM
“Load Optimized Default” to backup customized
Setting in
the BIOS flash chip to prevent from
CMOS battery fail
„ System Memory: One 184-pin DIMM socket
200/266/333MHz ECC/non-ECC DDR
SDRAM
supported Maximum SDRAM of
up to
1GB
„ L2 Cache: Integrated in CPU
„ Bus Clock: 400 MHz
„ Watchdog Timer: Integrate Intel
®
6300ESB
Up to 300 levels as Reset feature
2 Introduction

PC 6170 User’s Manual
I/O System
„ Standard I/O:
− 3 x serial ports with power; 2 x RS-232, 1 x
RS-232/422/485 jumper selectable
− 1 x parallel port, SPP/EPP/ECP
− 1 x PS/2 for Keyboard Interface
− 1 x PS/2 for Mouse Interface
− 3 x USB Ports 2.0 compliant(1 at rear; 2 at front panel)
− 1 x 1 5 pin(female) for VGA output
„ Ethernet :
Realtek 8100C PCI Bus 10/100M Base-T
Wake On
LAN (via ATX power supply)
Equipped with
RJ-45 interface
Realtek RTL8110S for 10/100/1000Base-T
„ Audio :
Realtek ALC202A AC’97 codec audio
Amplify for speaker-out with 2.5 W for each channel
MIC-in, Line-in,
Line-out/Speaker-out (jumper
selectable)
„ Onboard IDE:
4 channels up to 6 devices (2 parallel ATA-100 and 2
serial ATA-150)
RATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra
DMA/33/66/100
„ Onboard Serial ATA:
Independent DMA operation on two ports.
Data transfer
rate up to 150 Mbyte/s
Altemate Device IDE and RAID Class Code option for
support of Soft RAID.
Introduction 3

PC 6170 User’s Manual
System Specification
„ 17” TFT LCD
„ Disk drive housing:
− 1x Build-in Slim type FDD,
− 1x optional slim type CD-ROM diver,
− 1 x internal 3.5” drive (or 2X 2.5” HDD)
 180W AC power supply
 Heat dispensing design

One slot for PCI expansion
 Net weight:
− 13.5 Kgs
 Dimension (main body size):
− 482.8 x 354.8 x 105.9 mm
 Operating temperature:
− O° to 45°C ; Relative umidity:50%
 Relative humidity:
− 10% to 85% @ 40° C, on-condensing
 Altitude:
− 10,000 ft. (3,000 meters)
 Vibration (operating):
− 5 to 500 Hz, 1 G random
 Shock (operating):
− 10 G peak acceleration (11 msec. duration)
4 Introduction

PC 6170 User’s Manual
1.3 Dimensions
The following diagrams show the dimensions and outlines of
PC 6170.
Introduction 5

PC 6170 User’s Manual
1.4 Front View and I/O Outlets
1.4.1 Front View
The figure below shows the features and controls on the
PC 6170 front panel.
6 Introduction

PC 6170 User’s Manual
1.4.2 I/O Outlet
The following figure shows the I/O locations of the PC 6170. Most of
the I/O connectors are located on the back panel of the PC 6170.
16 12 11
17
9 8 5 4 3
15 14
13
10
7 6 2 1
1: AC inlet 10: VGA
2: Power Switch 11: USB v 2.0
3: Line-in 12: COM3 Port(for T/S)
4: Mic 13: COM1 Port
5: Line-Out 14: COM2 Port
6: Mouse 15: COM4 Port
7: Keyboard 16: PRN (Parallel Port)
8: 10/100 Ethernet 17: PCMCIA Slot
9: 10/100/1000 Ethernet
Introduction 7

PC 6170 User’s Manual
1.5 Package list
When you receive the PC 6170 there are following items in the
package.
1. P1170-810 x 1
2. CPU cooler x 1
3. AC power cord x 1 (U.S standard)
4. Panel mount kit x 10
5. Desktop kit x 2
6. VESA ARM kit x 1
7. Wall mount kit x 1
8. CD driver x1
8 Introduction

PC 6170 User’s Manual
C h a p t e r 2
Hardware Installation
The PC 6170 provides lots of flexible ways for you to select different
configuration such as
CPU, CD-ROM and more. The chapter will show
you how to install the hardware. It includes:
2.1 CPU and DRAM Installation
The standard PC 6170 system was designed Pentium M level CPUs.
The build-in CPU board provides one 184-pin DDR DIMM socket
that supports system memory up to 1GB. And, there is one mini-
PCI type-III Socket.
When upgrading the CPU, DRAM, or Mini-PCI, refer to the following
instructions and illustration:
1. Unscrew five screws in the back door.
Hardware Installation
9

PC 6170 User’s Manual
2. Install the CPU, DDR DRAM and Mini-PCI card in the
P-1170-810.
DRAM
CPU
Mini-PCI
10 Hardware Installation

PC 6170 User’s Manual
2.2 HDD Installation
The PC 6170 offers a convenient drive bay module for users to install
HDD. The PC 6170
offers one 3.5” HDD drive for users to install.
If you want to install two 2.5” HDDs, the PC 6170 also
provides the 3.5” to 2.5” drive holder to
meet your requirement.
Please follow
the steps:
1. Open the back door.
2. Unscrew 3 screws and remove the riser card bracket kit.
Hardware Installation
11

C 6170 User’s Manual
3. Unscrew 1 screw from the HDD drive bracket, and push the HDD
bracket kit.
(1) Unscrew the
screw
(2) Push the HDD
bracket kit
4. Set the 3.5” HDD (or 2.5” HDD) in the HDD bracket kit and fix it by
4 screws around the bracket kit.
5. Installation complete.
12 Hardware Installation