ACT 5 PROX User manual

ACT5prox
Operating & Installation Instructions
18-00042
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 1

Pin & Prox Reader: ACT5prox
Proximity Card: ACTProx ISO-B
Proximity Fob: ACTProx Fob-B
Proximity Half Shell Card: ACTProx HS-B
Proximity & Magnetic Stripe Card: ACTProx DUO-B
ACT5pr x Operating and Installati n Instructi ns
2
Ins alla ion No es
• Remember to Factory Default the ACT5prox before programming
• Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay
contacts
• Don’t mount the ACT5prox units near RF sources (Eg mobile phones, radio transmitters, computer
monitors) or metal surfaces.
• Don’t power the unit from a switch-mode power supply. Use a linear regulated power supply.
• Never use the on-board relay to switch AC mains voltage. An external relay, electrically isolated from
the ACT5prox should be used for this purpose
• Remember to change the programming code.
• When ordering new cards or fobs specify ACTRFID. ACT5prox will NOT work with HID cards or
fobs.
Impor an
As with any Access Control system, always ensure there is an alternate means of escape in the event of
the unit failing to operate due to power loss or in the event of fire.
Produc Specifica ion
Number of sers 50 (50 unique PINs and 50 Cards)
Supply Voltage 12 - 24V AC or DC (linear PSU)
Current Consumption 60mA (nominal), 100mA (maximum)
Operating Temperature -10 to +50 degrees C
Door Open Time 0 - 255 seconds
Relay Contact Rating 5A / 500Vac
Controller Size Flush Mount 100 x 110 x 20 mm
Surface Mount: 100 x 110 x 35 mm
Controller Weight 200 grams
Water Resistance High IP67
Construction Rugged Polycarbonate housing with stainless steel keys
and potted electronics.
Ordering Informa ion
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 2

ACT5pr x Operating and Installati n Instructi ns
3
Unit C1, South City Business Centre,
Tallaght, Dublin 24, Irelan
Tel: [phone] Fax: [phone] UK Locall: 0845 300 5204
Web: http://www.accesscontrol.ie E-mail: [email protected]
Copyright ©2007 Access Control Technology Ltd.
30 Second Programming Guide
(For typical Standalone System)
1. Enter Programming Mode.
On the digital keypad press button ✘. Input the programming code (default is 9999).
The LED will flash amber.
2. Change ser 1 Code
On the digital keypad press button 0. Input 01 (for User 01). Input the new User 1
code (4 digits)
3. Add ser 1 Card
On the digital keypad press button 5. Input 01 (for User 01). Present User 1’s card twice.
4. Change Programming code
On the digital keypad press button 0. Press ✔. Input the new programming code (4 digits)
5. Exit Programming Mode
On the digital keypad press button ✘. The LED turns red and programming mode
has been exited.
5. Record ser Code and Card
Enter the details of the Users and their associated codes and card numbers on the User List at
the back of this manual.
The ACT5prox is now ready for normal use.
Note: The ACT5prox may be returned to its factory default condition at any time by entering the
programming mode and and pressing Button ✔three times.
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 3

0 Change PIN code 1234 – User 1, 9999 - Programming Code
1 Set Toggle Mode Off (Timed Relay)
2 Set Door Relay Time 5 seconds
5 Add User Card
6 Delete User’s Card
7 Delete Card Number
30 Card or PIN On
31 Card and PIN Off
32 Card and any PIN Off
40 Permanent Backlight On
41 Auto Backlighting Off
80 Check PIN User
81 Check Card User
ACT5pr x Operating and Installati n Instructi ns
4
Programming Summary
Code Function Default
ACT5prox Opera ion
The ACT5prox is a simple, easy-to-use access control unit combining digital keypad and proximity
technology. The unit supports up to 50 users, each with a unique PIN code and proximity card/fob.
Each unit is contained in rugged polycarbonate housing, with stainless steel keys and potted
electronics, allowing for indoor and outdoor installation. Keypad backlighting enhances the
ACT5prox functionality at night or in poor light conditions.
Programming the unit is achieved via the keys, LED and buzzer. Cards and PIN codes can be
programmed into the ACT5prox very quickly. ACT recommends that sers and their associated
PIN and Card are recorded in the ser List at the end of the manual. Make copies of this sheet
and enter each Users details on it. This will allow users to be deleted later on, even if a card is lost or
a user forgets their PIN code. Blank ser List forms can be downloaded from the Resource
Centre on the ACT website, www.accesscontrol.ie
A valid card or PIN will allow access through the ACT5prox unit. For axi u security, the unit
ay be progra ed to require all users to enter a PIN code after presenting a card.
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 4

Step Keypad Entry Operation Example: Assign code 7529 to user 7
10 Change PIN codes ✘9999 Enter programming
2 00-49 Enter 2 digit User Number 00-49 0 Change PIN codes
3 0000-9999 4 digit code – 0000 deletes User code 07 User 7
7529 PIN code
✘Exit programming
ACT5pr x Operating and Installati n Instructi ns
ACT5prox Programming
On the digital keypad press the button ✘and input the programming code (initially 9999). The LED
will flash amber while in programming mode. To exit the programming mode either press button ✘or
do not activate any key for 30 seconds.
• If the LED flashes green during programming, then a card presentation is expected.
• If the LED flashes red, then a keypress is expected.
• While the ACT5prox is busy performing a task, (eg. Defaulting memory, adding cards), the
green led will turn on and the buzzer will sound an elongated tone.
Changing U er PIN Code : Enter Pr gramming M de, then Press
Step Keypad Entry Operation
15 Add Card
2 00-49 First user to be assigned card
3 Present Card First Card in Batch (lowest number card) assigned to first user
4 Present Card Last Card in Batch (highest number card) assigned to last user
Adding Card : Enter Pr gramming M de, then Press
*Re e ber to update the user list docu ent at the back of this anual after adding a PIN or Card
Cards ay only be assigned to users that do NOT have a card already assigned. When adding cards to
the ACT5prox, check which users already have cards by using option 81 (see page 7).
5
Example: Assign card 0000200036 to user 21: Example: Assign card 0000200036 to user 21
using the keypad:
Keypad Entry Operation Keypad Entry Operation
✘9999 Enter programming ✘9999 Enter programming
5 Add card 5 Add card
21 User 21 21 User 21
Present card Card number 0000200036 0000200036 Enter 10 digit card number
Wait 2 seconds 0000200036 Enter 10 digit card number
Present Card Card number 0000200036 ✘Exit programming
✘Exit programming
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 5

ACT5pr x Operating and Installati n Instructi ns
6
Step Keypad Entry Operation
10 Change Programming code (Default 9999)
2 Press ✔
3 0000-9999 New 4 digit programming code
Change Programming Code: Enter Pr gramming M de, then Press
Step Keypad Entry Operation
12 Set Door Relay Time – (default 5 seconds, maximum 255 seconds)
20 Buzzer sounds indicating timing… wait required period
3✔End setting Door Relay Timer
Set Door Relay Time: Enter Pr gramming M de, then Press
Step Keypad Entry Operation Example: Assign Toggle made to user 12
11 Set Toggle Mode ✘9999 Enter programming
2 00-49 Enter 2 digit User Number 00-49 1 Set Toggle Mode
3 0 or 1 0 = Relay Toggle, 1 = Relay Timed 12 User 12
0 Relay toggle
✘Exit programming
Set Toggle Mode: Enter Pr gramming M de, then Press
Step Keypad Entry Operation Example: Delete user 10’s card
16 Delete User’s Card ✘9999 Enter programming
2 00-49 First user to delete 6 Delete cards
3 00-49 Last user to delete 10 User 10
10 User 10
✘Exit programming
Deleting U erʼ Card: Enter Pr gramming M de, then Press
Step Keypad Entry Operation
17 Delete card number
2 10 digit card number 10-digit Card number with leading zeroes.
Eg. Card 54321, enter 0000054321
Deleting Card Number: Enter Pr gramming M de, then Press
Step Keypad Entry Operation
1 80 Check if user has no PIN already assigned
2 00-49 User 0-49
eypad will flash the green led and sound high-pitched tone if the user has NO
PIN code assigned. It will flash red and sound low-pitched tone, if the user has
a PIN code.
Check if U er ha no PIN A igned: Enter Pr gramming M de, then Press
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 6

ACT5pr x Operating and Installati n Instructi ns
7
Step Keypad Entry Operation
1 81 Check for user with no card assigned
2 00-49 User 0-49
eypad will flash the green led and sound high-pitched tone if the user has NO
card assigned. It will flash red and sound low-pitched tone, if the user has a card.
Check if U er ha no Card A igned: Enter Pr gramming M de, then Press
Programming ACT5prox Option Enter Pr gramming M de, then Press
Option Function Default Operation
30 Card or PIN On When set, a valid Card or valid PIN will open the door.
31 Card and PIN Off When set, only users with both a Card and PIN are admitted. Cards
are assigned to a particular user using the Adding Cards function
(function 5) and PINs are assigned using the Changing PIN Codes
function (function 0).
32 Card and any PIN Off In this mode, a valid card and any valid PIN code will open the
door. This mode allows all users to have a common PIN code to
use with their cards.
40 Permanent Off When set, the keypad illumination is always on. This option will
Backlight override option 41 (Auto Backlighting)
41 Auto Backlighting On When set, the keypad illumination is normally off, but will switch
on in response to any key being pressed, or when a card is
presented or while in programming mode. This option is
overridden by option 40 (Permanent Backlight). To prevent any
illumination, turn off options 40 and 41.
Res oring Fac ory Defaul s
Enter Programming Code followed by ✔✔✔. This restores the ACT5prox to its default settings.
If the Programming Code has been forgotten, it may be set to 9999 by:
1. Remove the power from the unit.
2. Remove link L 1 at the back of the unit.
3. Apply power to unit.
4. Replace link L 1.
5. Programming Code is now set to 9999.
Note: The keypad will not operate correctly without L 1 in place.
Defaulting memory takes 3-4 seconds. During this time, the buzzer will sound an elongated tone.
Step Keypad Entry Operation
1 30, 31,32,40 or 41 2 digit option number
2 0 or 1 0=Off, 1= On
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 7

8
N/O
Comm
N/C
BATCH:
PRODUCT
SERIAL NUMBER
01XX-
ACT5prox
00XXX X
Note :
The ACT5prox may be powered from 12 or 24V AC or DC.
Door Release Button
Power
Supply Unit
This illustration shows wiring for normally de-energised locks. If normally energised locks are required, use the N/C relay contacts .
Important!
Always Place Varistor Across Lock Terminals
+12V
0V
12-24V
AC/DC
Push Button
0V
SCHRACK
12V = DC
5A/250V ~AC
LK1 Power up without link if
Programming code has been lost
ACT5prox Wiring Diagram for Door Strike Locks
Fig 1
ACT5pr x Operating and Installati n Instructi ns
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 8

9
N/O
Comm
N/C
BATCH:
PRODUCT
SERIAL NUMBER
01XX-
ACT5prox
00XXX X
Note :
The ACT5prox may be powered from 12 or 24V AC or DC.
Door Release Button
Power
Supply Unit
This illustration shows wiring for normally de-energised locks. If normally energised locks are required, use the N/C relay contacts .
Important!
Always Place Varistor Across Lock Terminals
12-24V
AC/DC
Push Button
0V
SCHRACK
12V = DC
5A/250V ~AC
LK1 Power up without link if
Programming code has been lost
Break Glass Unit (optional)
ACT5prox Wiring Diagram for Mag Lock
Fig 2
ACT5pr x Operating and Installati n Instructi ns
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 9

10
Security screw supplied with
the unit.
Place the Reader / Keypad onto the surface mount collar and clip down into place.Use the security
screw supplied to attach the unit to the surfce mount
collar.
Mounting instructions for flush mount unit
Mounting plate is attached to the pattress box using the screws supplied. Ensure the corect spacers have been used to bridge the gap between the mounting plate and the fixing wings of the pattress box to avoid the mounting plate being
distorted.
Standard pattress
box.
Fig 2
Spacers break away from main component when
required by
installer for use.
Screws
Place the cap onto the unit and push firmly into place.
View showing
spacers stacking
Note: Determine the distance between the pattress box and the mounting plate, using the spacers which are labelled 1mm to 4mm. This allows the installer to make the required spacer length, from 1mm to 10mm, by stacking spacers.
View showing mounting plate before spacers are broken away.
3
ACT5pr x Operating and Installati n Instructi ns
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 10

11
Mounting instructions for surface mount unit
Place the Reader / Keypad onto the
surface mount collar and clip down into
place.Use the security screw supplied to
attach the unit to the surfce mount colla
Fig 3
The surface mount collar is mounted on the wall using the fixing kit supplied in the box.
Security screw supplied with
the unit.
Place the cap onto the unit and push firmly into place.
4
ACT5pr x Operating and Installati n Instructi ns
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 11

U er U er Name Card Number PIN Toggle
User Lis
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: te h@a ess ontrol.ie
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Ac 12pp ACT5prox:Ac 20pp 1.1 English 14/11/2007 13:10 Page 12