ActionTec GT724WGR User manual

Wireless
DSL Modem
Model #: GT724WGR
User Manual
Ver 1.0
Solutions for the Digital Life™

Table of Contents
1 Introduction 1
Minimum System Requirements 1
Features 2
Getting to Know the Modem 3
2 Performing a Quick Setup 7
Accessing Quick Setup Screens 7
Changing the Password 9
3 Viewing the Modem’s Status 11
Broadband Connection Status 11
Network Status 14
4 Configuring Wireless Settings 15
Accessing Wireless Setup 15
Basic Wireless Setup 17
Wireless Advanced Settings 17
Wireless Status 23
5 Configuring Advanced Setup Options 25
Accessing the Advanced Setup Options 25
DSL Settings 27
DHCP Settings 28
LAN IP Address 30
WAN IP Address 31
QoS Settings Upstream 33
QoS Settings Downstream 35
QoS Status 36
Remote Management 36
Telnet Timeout Setting 37
Dynamic Routing 38
Static Routing 38
UPnP (Universal Plug and Play) 39
Time Zone 39
Remote Syslog Capture 40
i

ii
Actiontec Wireless DSL Modem User Manual
ii
6 Configuring Security Settings 41
Accessing Wired Security Screens 41
Admin User Name and Password 42
Firewall 43
Port Forwarding 47
DMZ Hosting 49
NAT (Network Address Translation) 50
7 Configuring Internet Access Controls 51
Accessing Internet Access Control Screens 51
Services Blocking 52
Website Blocking 53
Schedule Rules 54
8 Configuring the Modem’s Utilities 57
Accessing the Utilities Screens 57
Restore Default Settings 59
Upgrade Firmware 59
Web Activity Log 60
System Log 61
OAM Ping Test 62
Ping Test 62
Reboot 63
9 Troubleshooting 65
Troubleshooting 65
Frequently Asked Questions 67
A Specifications 73
General 73
Wireless Operating Range 74
LED Indicators 74
Environmental 74
B Setting up Static IPon a Computer 75
Windows 2000 75
Windows XP 80
Windows Vista 83
C Service Acronyms 87
Service Acronym Definitions 87
D Glossary 91
Notices 95
Regulatory Compliance Notices 95
Modifications 95
Limited Warranty 97

1
Introduction
Thank you for purchasing the Actiontec Wireless DSL Modem. The Modem is the
simplest way to connect computers to a high-speed broadband connection. This
easy-to-use product is perfect for the home office or small business. If you want to
take your computing to the next level, the Wireless DSL Modem is sure to be one
of the keys to your success.
Minimum System Requirements
s Active DSL service
s Computer with a 10 Mbps or 10/100 Mbps Ethernet connection
s Microsoft Windows 2000, XP, Vista
Mac OS 7.1+, 8.0+, 9.0+, OS X+
s Internet Explorer 4.0 or higher (5.x+ recommended) or Netscape Navigator
4.0 or higher (4.7+ recommended)
s TCP/IP network protocol installed on each computer
1

2
Actiontec Wireless DSL Modem User Manual
3
Chapter 1 Introduction
Features
s ADSL WAN port (RJ-11)
s Full-rate ANSI T1.413 Issue 2, ITU G.992.1(G.dmt) and G.992.2(G.lite)
standard compliance
s Auto-handshake for different ADSL services
s Bridged Ethernet over ATM, PPP over ATM, PPP over Ethernet
s Precise ATM traffic shaping
s IP packet routing and transparent bridge
s RIP-1, RIP-2, and static routing protocol support
s Built-in NAT, DHCP server
s DNS relay support
s PAP/CHAP authentication, administrative passwords through Telnet
s 64-, 128-, and 256-bit WEP/WPA wireless LAN security
s IEEE 802.3 Ethernet standard compliance
s 10/100 Base-T Ethernet ports (4)
s Fast Ethernet flow control support
s Web-based configuration setup
s FTP firmware upgradeable
s Web download support
s 802.11b/g support

2
Actiontec Wireless DSL Modem User Manual
3
Chapter 1 Introduction
Getting to Know the Modem
This section contains a quick description of the Modem’s lights, ports, etc.
The Modem has several indicator lights (LEDs) on its front panel and a series of
ports on its rear panel.
Front Panel
The front panel of the Modem features eight lights: Power, DSL, Internet,
Ethernet (4), and Wireless.
Power Light
The Power light displays the Modem’s current status. If the Power light glows
steadily green, the Modem is receiving power and fully operational. When the
Power light is rapidly flashing, the Modem is initializing. If the Power light glows
red when the Power cord is plugged in, the Modem has suffered a critical error
and technical support should be contacted.
DSL Light
The DSL light illuminates when the Modem is connected to a DSL line and the
unit is able to synchronize to the DSL signal from the ISP. When it flashes, the
Modem’s built-in DSL modem is training for the DSL service.

4
Actiontec Wireless DSL Modem User Manual
5
Chapter 1 Introduction
Internet Light
When the Internet light glows steadily, the Modem is connected to the
DSL provider.
Ethernet Lights
The Ethernet lights illuminate when the Modem is connected to one or more
computers via its yellow Ethernet ports.
Wireless Light
The Wireless light illuminates when the Modem’s wireless radio is turned on.
Rear Panel
The rear panel of the Modem contains six ports (Ethernet [4], Line, and Power), as
well as Reset and Power switches.
12VDC 0 6A
Reset
ON OFF
1
2
3
4
Ethernet Ports
The Ethernet ports are used to connect computers to the Modem via Ethernet
cable. The Ethernet ports are 10/100 Mbps auto-sensing ports, and either a
straight-through or crossover Ethernet cable can be used when connecting to
the ports.
Line Port
The Line port is used to connect the Modem to a DSL (Digital Subcriber
Line) connection.

4
Actiontec Wireless DSL Modem User Manual
5
Chapter 1 Introduction
Reset Switch
Depressing the Reset switch restores the Modem’s factory default settings. To
reset the Modem, depress and hold the Reset switch for five to seven seconds.
The reset process will start after releasing the switch, during which the Power
light will turn from green to orange.
Power Port
The Power port is used to connect the Power cord to the Modem.
N Warning: Do not unplug the Power cord from the Modem dur-
ing the reset process. Doing so may result in permanent damage
to the Modem.
Power Switch
The Power switch is used to power the Modem on and off.

6
Actiontec Wireless DSL Modem User Manual
This page left intentionally blank.

7
Performing a
Quick Setup
This chapter is a guide through a quick set up of the Modem, including how to
connect the Modem to the ISP.
To complete the quick setup, have the Welcome Letter or ISP Worksheet handy. If
the document is not available, contact the ISP immediately.
Accessing Quick Setup Screens
To access the Quick Setup screens:
1. Open a Web browser. In the “Address” text box, type:
http://192.168.0.1
then press Enter on the keyboard.
2

8
Actiontec Wireless DSL Modem User Manual
9
Chapter 2 Performing a Quick Setup
2. Another screen appears. Click Manual Setup for Internet Access.
3. Follow the instructions in the “Welcome to the Quick Setup” screen, then click Next.
4. At the top of the next window, select the type of connection used by the ISP.
4a. If PPPoA or PPPoE was selected in step 4, the default user name and pass-
word are entered in the appropriate text boxes.
If “RFC1483 via DHCP” was selected, go to step 5.

8
Actiontec Wireless DSL Modem User Manual
9
Chapter 2 Performing a Quick Setup
5. Click Apply at the bottom of the screen.
6. Read the instructions on the next screen. The Modem is successfully
configured.
The Power light flashes rapidly while the Modem restarts, then glows steadily
green when fully operational. The Internet light will also glow steadily green. The
Modem is now configured and users can start surfing the Internet.
If an error appears, stating the Web browser was unable to connect to the Internet,
check the configuration settings. Ensure all the information required by the ISP is
entered correctly.
Changing the Password
To create or change the password allowing access to the Modem’s Web
Configuration screens, follow these instructions:
1. From the “Home” screen, select Security.
2. The “Security” screen appears. Select “Admin User Name and Password.”
3. The “Change Admin Username/Password” screen appears. Enter a new
Username in the “Admin User Name” text boxt, then enter a new password in
the “Admin Password” text box. Make sure to write down the user name and
password and keep it in a secure location. They will be needed to access the
Modem’s Web Configuration screens in the future.

10
Actiontec Wireless DSL Modem User Manual
4. Click Apply at the bottom of the screen.
5. Read the instructions on the next screen. The user name and password are
successfully changed.
Once the Modem has rebooted, the new user name and password are active. To
access the Modem’s Web Configuration screens, the new user name and password
must be entered.

11
Viewing the
Modem’s Status
After configuring the Modem, the Modem’s connection and network status can be
viewed. The Internet connection status is viewed in the “Broadband Connection
Status” screen, while the network status is viewed in the “My Network” screen.
Broadband Connection Status
To view the Modem’s connection statistics, select Status from the strip of icons at
the top of any Gatetway GUI screen. The “Broadband Connection Status” screen
appears. There are three sections in this screen: General Statistics, PPP Status, and
DSL Status.
☞
Note: No settings (other than connecting or disconnecting from
the Internet by clicking on Connect or Disconnect) can be
changed from the Broadband Connection Status screen.
General Statistics
The top section of the Broadband Connection Status screen displays general statis-
tics regarding the Modem, including model number, firmware version, IP address,
and gateway IP address.
3

12
Actiontec Wireless DSL Modem User Manual
13
Chapter 3 Viewing the Modem’s Status
PPP Status
The middle section of the Broadband Connection Status screen displays the status
of the Modem’s PPP connection, including user name, authentication failures, and
packets sent and received.
DSL Status
The bottom section of the Broadband Connection Status screen displays the status
of the Modem’s DSL connection, including mode settings, connection status, and
number of discarded packets. Click Reset to refresh all statistics on this screen.

12
Actiontec Wireless DSL Modem User Manual
13
Chapter 3 Viewing the Modem’s Status
In the menu on the left side of the Broadband Connection Status screen, there are
two other options available to view: NAT Table and Routing Table. Click to gen-
erate the option of choice.
NAT Table
Selecting NAT Table generates the “NAT Table” screen. This screen displays an overview
of the current list of open connections through NAT (Network Address Translation) the
Modem supports between the networked computers and the Internet.
Routing Table
Selecting Routing Table generates the “Routing Table” screen. This screen displays
an overview of the Modem’s network routes.

14
Actiontec Wireless DSL Modem User Manual
Network Status
To view the Modem’s network status, select My Network from the strip of icons
at the top of any Modem GUI screen. The “My Network” screen appears, listing
all devices connected to the network. From this screen, various settings can be
accessed, including Website blocking, Schedule Rules, and Enable Application.
To view the network status of a particular device, click View Device Details for
the device. An overview of the device’s network status appears.

15
#
Configuring
Wireless Settings
This chapter explains how to set up the Modem’s wireless network capabilities, includ-
ing setting up wireless security and viewing the wireless connection status.
Accessing Wireless Setup
To access the Wireless Settings configuration screens, follow these instructions:
1. Open a Web browser. In the “Address” text box, type:
http://192.168.0.1
then press Enter on the keyboard.
2. The Main screen appears. Click Wireless Setup.
4

16
Actiontec Wireless DSL Modem User Manual
17
Chapter 4 Configuring Wireless Settings
3. A login window appears. Enter the user name and password in the appropri-
ate text boxes, then click OK.
☞ Note: The default user name is “admin.” The default password is
“password.”
4. The “Wireless Basic Settings” screen appears, which guides the user through a
basic set up of the Modem’s wireless networking capabilities.

16
Actiontec Wireless DSL Modem User Manual
17
Chapter 4 Configuring Wireless Settings
Basic Wireless Setup
To perform a basic setup of a wireless network using the Modem:
1. In the “Wireless Basic Settings” screen, turn the Modem’s wireless radio on by
selecting On.
2. Create a name for the wireless network and enter it in the “ESSID” text box.
3. Select a channel from the “Channel” drop-down menu. In the United States,
use channels 1-11.
4. Activate WPA-PSK (Wi-Fi Protected Access w/ Pre-Shared Key) to secure the
wireless network by selecting WPA-PSK.
5. Enter eight alphamumeric characters in the “Pre-Shared Key (PSK) for Home
Network” text box.
6. Click Save to save the wireless settings.
Wireless Advanced Settings
To access the Modem’s wireless advanced settings screens, select Advanced
Settings from the menu on the left side of the “Wireless Basic Settings” screen.
This generates the “Wireless Advanced Settings” screen. In this screen, the security of
the wireless network can be activated and fortified.