ActronAir Classic 2 EVA100S User manual

Classic Series 2
Split Ducted Unit
Installation and Commissioning Guide - Indoor
Model Numbers
Single Fan Coil Split Fan Coil**
EVA100S*
EVA130S
EVA150S
EVA170S
EVA200S
EVA230S
EAA130S & EFA130S
EAA150S & EFA150S
EAA170S & EFA170S
EAA200S & EFA200S
EAA230S & EFA230S
* Above unit illustration shown is an EVA130S unit.
EVA100S has a single fan configuration.
** Split fan coil has a separate coil and fan section.
IMPORTANT NOTE:
Please read this manual carefully before installing or operating your air conditioning unit.
That’s better. That’s Actron.

Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
Installation and Commissioning Guide Split Ducted Indoor Units
2
Table of Contents
01. Introduction ...................................................................................................................................3
. Information About This Guide 
. Product Inspections 
. Codes, Regulations And Standards 
. Important Safety Symbols And Labels 
02. Safety Instructions .........................................................................................................................4
03. Components Overview ...................................................................................................................5
. Indoor Unit Components Overview 
. Indoor Unit Electrical Panel Overview 
04. Unit Dimensions and Clearances ....................................................................................................6
. EVAS 
. EVAS 
. EVAS 
. EVAS 
. EVAS 
. EVAS 
05. Two-Piece Fan Coil .......................................................................................................................12
. Coil Section 
. Fan Section 
06. Installation Instructions ...............................................................................................................19
07. Unit Lifting Procedures .................................................................................................................21
. Crane Lifting Method 
. Fork Lift Method 
08. Safety Drain Tray .........................................................................................................................23
09. Zone Barrel Installation Instructions .............................................................................................24
10. Electrical Installation ....................................................................................................................25
11. Wiring Diagram ............................................................................................................................26
12. Split Unit Electrical Connection ....................................................................................................27
13. Maximum Cable Lengths .............................................................................................................29
. Wall Controller Options 
. Wiring Configuration : Recommended 
. Alternate Wiring Configuration 
14. Cable Length - Zoning ..................................................................................................................32
15. Wiring Connections .....................................................................................................................33
. LR- and LC- Wall Control Wiring Connections 
. NEO Wall Control Wiring Connections 
. LM-RS- Optional Sensor Wiring Connections 
. AERSS Optional Duct Sensor Wiring Connections 
16. Zone Commissioning ....................................................................................................................35
17. Maintenance Frequency Checklist ................................................................................................36
18. Key Parts List ................................................................................................................................37

Installation and Commissioning Guide Split Ducted Indoor Units
Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
3
01. Introduction
CONGRATULATIONS on your purchase of an ActronAir air conditioning system! This unit has been designed and
engineered to provide optimum air conditioning and to achieve maximum energy efficiency.
Your air conditioning system has been manufactured from the highest quality materials. Numerous “in house” and “external”
inspection and test procedures were conducted to your air conditioning to ensure satisfactory operation.
. Information About This Guide
This guide provides installation instructions, specific to your split ducted indoor unit. Read this manual thoroughly and
take into consideration all specifications and instructions to ensure correct installation and safe operation of your air
conditioning system.
IMPORTANT
Keep this document for future reference. Ensure all technicians that work on the unit can refer to this manual at any time.
. Product Inspections
Check your air conditioning unit and all items against the invoice upon receiving your shipment. Inspect the unit,
components and accessories for any sign of damage. If there is any damage to the unit, contact ActronAir Customer
Care Department immediately on: 1300 522 722 to obtain a Goods Return Number.
Check the unit nameplate to verify the model, serial number, electrical rated specifications are correct.
. Codes, Regulations And Standards
The installer and/or contractor assumes responsibility to ensure that unit installation complies with the relevant
council, state / federal codes, regulations and building code standards. All electrical wiring must be in accordance with
current electrical authority regulations and all wiring connections to be as per electrical diagram provided with the unit.
. Important Safety Symbols And Labels
Safety Symbols and labels appear at appropriate sections throughout this manual to indicate immediate or potential
hazards. Pay full attention and comply to the safety information and instructions. Failure to follow safety instructions
increases the risks of personal injury, death and/or property damage. Damages to the product as a result of such failure
may void warranty.
ActronAir has endeavoured to provide sufficient safety warnings and recommendations, however current and
prevailing WH&S regulations must be observed and will take precedent whenever performing the installation
instructions discussed in this manual.

Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
Installation and Commissioning Guide Split Ducted Indoor Units
4
02.Safety Instructions
•Only licensed HVAC technicians* should install and service this air conditioning equipment. Improper service or
alteration by an unqualified technician could result in significant and major damage to the product or property which
may render your warranty null and void. Such unqualified service could also lead to severe physical injury or death.
Follow all safety instructions in this literature and all warning labels that are attached to the equipment.
•Prevailing WH&S regulations must be observed and will take precedence to the safety instructions contained on this
manual. Safe work practices and environment must be the paramount importance in the performance of all the service
procedures.
•Ensure that unit installation complies with relevant council regulations and building code standards.
•All electrical wiring must be in accordance with current electrical authority regulations and all wiring connections to be
as per electrical diagram provided.
•Secure the fans against accidental contact. Beware of pinch point and sharp edges which can cause cutting injury.
•Always wear appropriate PPE, remove any dangling jewellery and protect long hair by wearing a cap.
•Make sure that safety guards and panel covers are always firmly secured and not damaged.
•This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised
by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure
that they do not play with the appliance.
•Installer must incorporate a means of electrical disconnection (isolator) in the sub mains fixed wiring in accordance
with AS/NZS 3000:2018 (also known as Australian Wiring Rules).
•Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
*Qualifications required will be appropriate Electrical, Refrigeration and Refrigerant Handling License and Training
dependent on local State/Territory regulations.
DANGER
Hazardous Voltage - Risk of Electrocution.
TURN-OFF the power from main isolator before proceeding with any service work of the unit. Observe proper LOCK-OUT/
TAGOUT LOTO) procedures for electrical appliances in order to prevent accidental switching-on of the power supply.
CAUTION
Beware of Rotating Fans!
Ensure that indoor and outdoor fans are isolated and have come to a complete stand still before servicing the equipment.
Beware of pinch point and sharp edges which can cause cutting injury. Secure the fans against accidental contact.
Always wear appropriate PPE and remove any dangling jewellery and protect long hair by wearing a cap. Ensure that no loose
clothing can be caught / entangled in moving parts.
VISUAL INSPECTION AND WORK ASSESSMENT
Work areas and conditions must first be assessed and evaluated for any potential hazardous conditions. It is also important to be
familiar with the unit parts and components before proceeding with any service task.

Installation and Commissioning Guide Split Ducted Indoor Units
Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
5
03. Components Overview
. Indoor Unit Components Overview
EC MOTOR
INDOOR
UNIT
ID FAN
(Single Fan for EVA100S)ELECTRICAL
BOX COVER
ID COIL
INDOOR
CONTROL PANEL
. Indoor Unit Electrical Panel Overview
INDOOR UNIT
CONTROL BOARD
EMC FILTER
(for some models) TRANSFORMER

Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
Installation and Commissioning Guide Split Ducted Indoor Units
6
04.Unit Dimensions and Clearances
. EVAS
UNIT MODEL NUMBER UNIT WEIGHT
(kg)
EVA100S 37
770
SUPPLY
AIR
660
575
RETURN
AIR
65
45
410
O/A
175
20
20
810
235 267.5267.5
850 O/A
42
595 O/A
535 40
340
20
50
INDOOR
FAN
INDOOR COIL
SUPPLY
AIR
135
RETURN
AIR
GAS PIPE
Ø 15.9 mm (5/8") SWAGED
SAFETY DRAIN
Ø 20 mm ID
LIQUID PIPE
Ø 9.5 mm (3/8") SWAGED
PRIMARY DRAIN
Ø 20 mm OD
40
TOP VIEW
OVERALL NOMINAL DIMENSION
H X W X L
= 410 X 850 X 595
SUPPLY DUCT H X W
= 175 X 235 NO FLANGE
RETURN DUCT = 340 X 660
CONDENSATE DRAIN CONNECTION
= 20MM OD
FRONT VIEW SIDE VIEW
HEIGHT CLEARANCE = 340MM
DUCT WORK
DUCT WORK
850 MM
SERVICE
CLEARANCE
850 MM
SERVICE
CLEARANCE
ELECTRICALS
770
SUPPLY
AIR
660
575
RETURN
AIR
65
45
410
O/A
175
20
20
810
235 267.5267.5
850 O/A
42
595 O/A
535 40
340
20
50
INDOOR
FAN
INDOOR COIL
SUPPLY
AIR
135
RETURN
AIR
GAS PIPE
15.9 mm (5/8") SWAGED
SAFETY DRAIN TRAY
20 mm ID
BSP SOCKET
LIQUID PIPE
9.5 mm (3/8") SWAGED
CONDENSATE DRAIN
20 mm OD
BSP FEMALE THREAD
40
EC
ID FAN
INDOOR COIL
MINIMUM SERVICE ACCESS AREAS AND AIRFLOW CLEARANCES
NOTES:
1. Do not scale drawing. All dimensions are
in mm unless specified.
2. Service Clearances given are suggested
minimum based on the condition that
the spaces around the units are free
from any obstructions and a walkway
passage of 1000mm between the units
or between the unit and the outside
perimeter is available.
3. Minimum service access clearances are
responsibilities of the installer, ActronAir
will not be held liable for any extra
charges incurred due to lack of access.
THIRD ANGLE
PROJECTION

Installation and Commissioning Guide Split Ducted Indoor Units
Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
7
. EVAS
UNIT MODEL NUMBER UNIT WEIGHT
(kg)
EVA130S 49
NOTES:
1. Do not scale drawing. All dimensions are
in mm unless specified.
2. Service Clearances given are suggested
minimum based on the condition that
the spaces around the units are free
from any obstructions and a walkway
passage of 1000mm between the units
or between the unit and the outside
perimeter is available.
3. Minimum service access clearances are
responsibilities of the installer, ActronAir
will not be held liable for any extra
charges incurred due to lack of access.
THIRD ANGLE
PROJECTION
DUCT WORK
DUCT WORK
850 MM
SERVICE
CLEARANCE
850 MM
SERVICE
CLEARANCE
ELECTRICALS
EC
ID FAN
EC
ID FAN
INDOOR COIL
HEIGHT CLEARANCE = 340MM
MINIMUM SERVICE ACCESS AREAS AND AIRFLOW CLEARANCES
900
715
INDOOR COIL
1090 O/A
147.5
575
45 65
147.5
1050 115
80
412
O/A 340
22
50
RETURN
AIR
300
72
40
SUPPLY
AIR
615 O/A
535
40 40
SUPPLY AIR
EC
INDOOR
FAN
EC
INDOOR
FAN
OVERALL NOMINAL DIMENSION
H X W X L
= 412 X 1090 X 615
SUPPLY DUCT H X W = 300 X 715
RETURN DUCT = 340 X 900
CONDENSATE DRAIN CONNECTION
= 20MM OD
FRONT VIEW SIDE VIEW
TOP VIEW

Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
Installation and Commissioning Guide Split Ducted Indoor Units
8
. EVAS
DUCT WORK
DUCT WORK
850 MM
SERVICE
CLEARANCE
850 MM
SERVICE
CLEARANCE
ELECTRICALS
EC
ID FAN
EC
ID FAN
INDOOR COIL
HEIGHT CLEARANCE = 340MM
MINIMUM SERVICE ACCESS AREAS AND AIRFLOW CLEARANCES
OVERALL NOMINAL DIMENSION H X W X L
= 412 X 1290 X 615
SUPPLY DUCT H X W = 300 X 715
RETURN DUCT = 340 X 1100
CONDENSATE DRAIN CONNECTION
= 20MM OD
UNIT MODEL NUMBER UNIT WEIGHT
(kg)
EVA150S 53
1100
80
715
20 20
INDOOR COIL
412
O/A
615 O/A
1252
40
300
72
40
340
22
50
115
248.5 248.5
575
SUPPLY
AIR RETURN
AIR
1290 O/A
40
535
65
47
EC
INDOOR
FAN
EC
INDOOR
FAN
SUPPLY AIR
TOP VIEW
FRONT VIEW SIDE VIEW
NOTES:
1. Do not scale drawing. All dimensions are
in mm unless specified.
2. Service Clearances given are suggested
minimum based on the condition that
the spaces around the units are free
from any obstructions and a walkway
passage of 1000mm between the units
or between the unit and the outside
perimeter is available.
3. Minimum service access clearances are
responsibilities of the installer, ActronAir
will not be held liable for any extra
charges incurred due to lack of access.
THIRD ANGLE
PROJECTION

Installation and Commissioning Guide Split Ducted Indoor Units
Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
9
. EVAS
DUCT WORK
DUCT WORK
850 MM
SERVICE
CLEARANCE
850 MM
SERVICE
CLEARANCE
ELECTRICALS
EC
ID FAN
EC
ID FAN
INDOOR COIL
HEIGHT CLEARANCE = 410MM
MINIMUM SERVICE ACCESS AREAS AND AIRFLOW CLEARANCES
OVERALL NOMINAL DIMENSION H X W X L
= 412 X 1290 X 615
SUPPLY DUCT H X W = 300 X 715
RETURN DUCT = 340 X 1100
CONDENSATE DRAIN CONNECTION
= 20MM OD
UNIT MODEL NUMBER UNIT WEIGHT
(kg)
EVA150S 56
1100
80
715
20 20
INDOOR COIL
412
O/A
615 O/A
1252
40
300
72
40
340
22
50
115
248.5 248.5
575
SUPPLY
AIR RETURN
AIR
1290 O/A
40
535
65
47
EC
INDOOR
FAN
EC
INDOOR
FAN
SUPPLY AIR
TOP VIEW
FRONT VIEW SIDE VIEW
NOTES:
1. Do not scale drawing. All dimensions are
in mm unless specified.
2. Service Clearances given are suggested
minimum based on the condition that
the spaces around the units are free
from any obstructions and a walkway
passage of 1000mm between the units
or between the unit and the outside
perimeter is available.
3. Minimum service access clearances are
responsibilities of the installer, ActronAir
will not be held liable for any extra
charges incurred due to lack of access.
THIRD ANGLE
PROJECTION

Installation and Commissioning Guide - Split Ducted Indoor Unit
Doc. No.0525-074 Ver. 3 200811
Installation and Commissioning Guide Split Ducted Indoor Units
10
. EVAS
NOTES:
1. Do not scale drawing. All dimensions are
in mm unless specified.
2. Service Clearances given are suggested
minimum based on the condition that
the spaces around the units are free
from any obstructions and a walkway
passage of 1000mm between the units
or between the unit and the outside
perimeter is available.
3. Minimum service access clearances are
responsibilities of the installer, ActronAir
will not be held liable for any extra
charges incurred due to lack of access.
THIRD ANGLE
PROJECTION
DUCT WORK
DUCT WORK
850 MM
SERVICE
CLEARANCE
850 MM
SERVICE
CLEARANCE
ELECTRICALS
EC
ID FAN
EC
ID FAN
INDOOR COIL
HEIGHT CLEARANCE = 410MM
MINIMUM SERVICE ACCESS AREAS AND AIRFLOW CLEARANCES
OVERALL NOMINAL DIMENSION H X W X L
= 435 X 1420 X 680
SUPPLY DUCT H X W = 300 X 715
RETURN DUCT = 360 X 1140
CONDENSATE DRAIN CONNECTION
= 20MM OD
UNIT MODEL NUMBER UNIT WEIGHT
(kg)
EVA200S 72
SUPPLY
AIR
715
310 310
1420 O/A
1140
78 117
630
20 20
435
O/A
INDOOR COIL
1375
90
130
SUPPLY AIR
590
40 50
680 O/A
360
50
25
110
300
25
RETURN
AIR
EC
INDOOR
FAN
EC
INDOOR
FAN
TOP VIEW
FRONT VIEW
SIDE VIEW