ActronAir CP05 User manual

Commercial Control Interface
CP05/CP10
Operation Manual
IMPORTANT NOTE:
Please read this manual carefully before installing or operating your air conditioning unit.
That’s better. That’s Actron.
Model Number
CP05
(Supplied as Standard)
Model Number
CP10
(Optional) Esc
Prg

Operation Manual CP05 / CP10 Controller
2Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
Table of Contents
01. General Information .................................................................................................................. 3
02. Safety and Operational Precautions ..........................................................................................4
03. Operational Precautions............................................................................................................4
04. Advance Features ...................................................................................................................... 5
05. Control Interface Functions ......................................................................................................6
06. Menu Tree ................................................................................................................................. 9
07. Sub Menu Level Descriptions .................................................................................................. 10
08. Turn On /Off............................................................................................................................. 11
09. Backlight...................................................................................................................................12
10. Setting Room Temperature Setpoint ....................................................................................... 13
11. Setting The Temperature Setback............................................................................................14
12. Operation Mode....................................................................................................................... 15
13. Setting The Clock .....................................................................................................................16
14. Daylight Saving Time Enable ....................................................................................................18
15. Daylight Saving Time Disable...................................................................................................20
16. 7-Day Programming..................................................................................................................21
17. After Hours Timer.................................................................................................................... 23
18. 12 Programmable Special Days ................................................................................................ 24
19. Status....................................................................................................................................... 26
20. Alarm History ...........................................................................................................................27
21. Alarm Matrix ............................................................................................................................ 28
22. Troubleshooting Guide ........................................................................................................... 29
23. Maintenance............................................................................................................................ 30
24. System Information ..................................................................................................................31

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
3
Operation Manual CP05 / CP10 Controller
. General Information
CONGRATULATIONS! On your purchase of the latest ActronAir commercial range air conditioning system. With the
application of an intelligent interactive software technology controller, this system has been designed to give you many
years of reliable service and the convenience of menu-driven control. Your controller is manufactured from the highest
quality materials and has passed numerous in house and external inspection procedures to ensure years of satisfactory
operation.
IN THIS MANUAL: You will find instructions on how to program and utilise the many advanced features this controller
has to offer. Please take time to familiarise yourself with all these features, apply their functions to suit your optimum
comfort requirement and achieve energy cost savings at the same time. Thoroughly read this manual in order to ensure
correct installation and the safe utilisation of your ActronAir air conditioner.
IMPORTANT NOTICE: ActronAir base the development of its air conditioning products on more than 30 years of
experience in HVAC, sound and continuous investments in technological innovations and product improvements,
advancement in manufacturing processes and quality control through 100% functional product testing. However,
ActronAir cannot guarantee that all the aspects of the product and the software included with the product respond to
the requirements of final application, despite the product being developed according to state of the art technology. The
customer, both end user/specifier and installer, assume all liability and risks relating to the configuration of the product
in order to reach the expected results in relation to the specific design and system installation. ActronAir, based on
specific agreements, may be consulted for the positive commissioning, installation and application of the unit, however
in no case does ActronAir accept liability for the correct operation of the final equipment / system.
Your ActronAir air conditioning unit is one of the most advanced and innovative products in the market. Its operation
is specified in the technical documentation supplied with the product or which can be downloaded from our website:
www.actronair.com.au. Your air conditioner requires setup/configuration/programming in order to be able to operate
in the best possible way to suit your requirement. Failure to complete such operations, may result in malfunction and/or
damage to the unit, for which ActronAir accepts no liability.
Installation, commissioning and other technical services must only be carried out by a qualified technician. Ensure that
the unit installation complies with all relevant council regulations and building code standards. All electrical wiring must
be in accordance with current electrical authority regulations and all wiring connections to be as per electrical diagram
provided. Always use appropriate PPE for your safety and protection. Make sure that any safety guards and covers
are always firmly secured and not damaged. WH&S rules and regulations must be observed at all times and will take
precedence during installation process and operation of the unit.
In addition, the following instructions must be observed:
• Prevent the electrical components and electronic circuits from getting wet.
• Do not install the controlling devices in a particularly hot environment as extreme temperatures may damage the
electronic equipment.
• Do not attempt to open the controller and other electronic devices in any way other than described in this manual.
• Do not drop, shake or hit the devices, which can cause irreparable damage to its internal circuits and mechanisms.
• Do not use corrosive chemicals, solvents or other aggressive detergents to clean the unit and the control interface.
• Do not use the unit for applications other than those specified in the technical manual. Contact ActronAir for
technical data.
• Do not install the unit in environment with highly flammable, combustible and/or explosive articles and materials.
• The product, particularly the controlling devices, must be stored and installed in a location that complies with the
temperature and humidity limits specified in this manual.
ActronAir is constantly seeking ways to improve the design of its products, therefore specifications are subject to change
without prior notice. Please check with your ActronAir Technical Support Department on toll free number: 1800 119 229.
Storage and Operating Conditions
• Storage conditions: -20 to 70°C, 90% RH non-condensing
• Operating conditions: -10 to 60°C, 90% RH non-condensing

Operation Manual CP05 / CP10 Controller
4Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
Waste Electrical and Electronic Equipment Disposal Guidelines
1. Do not dispose off the waste electrical and electronic equipment with local council waste. These must be
disposed off through the council designated hazardous waste collection centre.
2. The terminal contains a battery that must be removed and separated from the rest of the product before
disposing off the terminal.
3. The equipment may contain hazardous substances, improper or incorrect disposal may have a negative
effect on human health and on the environment.
. Safety and Operational Precautions
1. Read all instructions in this manual before operating the air conditioning unit. Failure to do so may result in damage to
the unit and void your warranty.
2. Turn-Off power from mains supply by removing fuse or switching the circuit breaker to the Off position before
installation or servicing this control interface.
3. Beware of EC Motors with high power capacitors and which can have dangerous voltages at terminals for up to 5
min. after main power has been isolated. Wait at least 5 minutes after power isolation and test for high voltage before
performing service work.
4. EC Plug Fan has dual power supplies, i.e. 415V / 3Ph+N / 50Hz motor power supply plus 10VDC control power supply.
Care must be taken to ensure both are safely isolated to prevent personal injury and damage to the equipment.
5. Follow sound LOCK OUT/TAG OUT (LOTO) procedures to ensure that power supply is not re-energised accidentally.
6. This control interface has power supply from the control board via telephone connector, with voltage of 18 - 30VDC
Class II and maximum power input of 0.5W. Ensure that this unit is not installed on voltages higher than 30V DC supply.
7. Installation and/or servicing must be carried out by a qualified installer or technician.
8. Ensure that the unit installation complies with relevant council regulations and building code standards. All electrical
wiring must be in accordance with current electrical authority regulations and all wiring connections to be as per
electrical diagram provided.
9. WH&S rules and regulations must be observed and will take precedence during installation process.
10. Only use this wall controller with an ActronAir air conditioner as described in this operating manual.
. Operational Precautions
ACCESS PANELS AND GUARDS: NEVER remove any access panels or guards as this could cause injury from electric
shock and burns from extremely hot components. Never allow any bodily parts such as fingers or objects to protrude
through the fan guards or any other opening as they could cause personal injury and damage the air conditioner.
RETURN AIR FILTER: The air conditioner must never be operated without a return air filter as this will allow a build up of
dust or dirt on the indoor coil. This is very difficult to clean and can cause the system to operate inefficiently or even fail.
CRANKCASE HEATER PRECAUTION: The main power (switch board) to the system must be kept ON at all times to
prevent damage to the outdoor compressor. Should the main power be disconnected or interrupted for 6 hours or
longer, then no attempt should be made to start the system for 2 hours after the power has been restored to outdoor
unit. This allows the compressor to warm up, and remove any liquid refrigerant that may cause damage.

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
5
Operation Manual CP05 / CP10 Controller
. Advance Features
1Menu Tree Based Program Navigation
The control system features ease of operation via menu tree.
2LCD Display
The LCD displays the system mode, operation and fault diagnostics log.
3
LCD Backlight
The LCD backlight features instant On/Off backlighting to suit individual preferences in
viewing the displays. It can also be set to automatically Turn-Off after pressing the last button
and to instantly Turn-On at the press of any button.
4
7-Day Time Clock with 2 On/Off Events per Day
The Control Interface, through the 7-Day time clock function, can be programmed for each
day of the week to turn on or off your air conditioner. Each day has 2 ON / Off events which
you can set for your individual control preference.
5
12 Programmable Special Days with 2 On/Off Events per Day
12 Special Days can also be programmed within the year which provide you control flexibility to
satisfy your individual requirements.
5
Auto Defrost Function (Heating Mode)
At certain outdoor conditions (low temperature) there may be a build up of frost on the
outdoor heat exchanger. This gradual build up of frost reduces the performance of the air
conditioner. The controller will detect this frost build up and will automatically activate the
defrost mode.
6
Hot Start Function (Heating Mode)
When the air conditioner starts in heating mode, the indoor fan is delayed for a short period of
time, this allows the heat exchanger to warm up before the air flow starts, thus preventing cold
drafts. The hot start feature also activates itself when the system finishes defrosting.
7
Auto-Restart After Power Failure
On the event of power failure, the controller will automatically restart the air conditioner to the
previous state when the power is restored.
8
Return Air Filter Alarm Indication
This is a time based alarm control, which is used to indicate when the filters will need to be
checked for cleaning or replacement. The controller will not stop the air conditioning system
from operation, but will just indicate a warning alarm.
9
Dual Control Interface Operation ( Optional )
Two Control Interfaces can be installed on the commercial range air conditioning system.
Either of the controllers can control the air conditioning system and mimic each other,
displaying the same control parameters for ease of system control management.
10
Fault Diagnostics
In the unlikely event that a fault develops with the air conditioner the control system will
diagnose the fault (where possible) and display a date and time stamped fault log, with up to
100 events memory.

Operation Manual CP05 / CP10 Controller
6Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
. Control Interface Functions
Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
Defrost
10:20 Unit: Unit ON
3
4
2
1
6
5
7
4ESC Button
To exit programming menu.
5Scroll Up / Increment Button
To scroll up from existing menu or to
increase setting parameter.
6Enter Button
To lock the selected menu or to enter set
parameters.
7Scroll Down / Decrement Button
To scroll down from existing menu or to
decrease setting parameter.
1LCD Display
Displays the setting and operation
conditions (see menu page for details).
2Alarm / Reset Button
Alarm Indication and Reset Button.
3Program Button
To bring-up programming Main Menu
screen. (Display will revert back to default
screen after 5 minutes idle time at any
stage of programming).
System Default Screen
Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
Defrost
10:20 Unit: OFF by KEY
Current Time
Unit Control Indicator
by Control Interface
Actual Room Air
Temperature
Reversing Valve 2
ON / OFF Indicator
Actual Supply Air Temperature
(Optional via Multi Input)
Defrost Cycle
Indicator
Reversing Valve 1
ON / OFF Indicator
(Dark Filled arrow indicates ON)
Compressor 2
ON / OFF Indicator
(Dark Filled arrow indicates ON)
Compressor 1
ON / OFF Indicator
Other Unit Control Indicators:
• by Timeclock
• by 3rd Party
• by DRM
• by BMS
NOTES
CP05 and CP10 are two identical control interfaces with the same display and functions. The only differences are the
interface buttons and front case appearances. CP05 is supplied as standard, while CP10 is supplied as optional control
interface for commercial range air conditioning systems. This manual covers operations applicable to both control
interfaces, however CP05 control interface features are shown for ease of illustrations.

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
7
Operation Manual CP05 / CP10 Controller
POWER-UP (INITIALIZATION DISPLAYS COMPRESSORS AND REVERSING
VALVE STATUS INDICATIONS
Display Progression Display Progression
When the control interface is powered ON for the first
time, The display will be blank for 5 - 10 seconds
Room T. : 22.5oC
oC
Supply T. :
Comp Rev Vlv
10:20 Unit: Unit ON
Both Compressors and Reversing Valves are Off, as
indicated by clear triangles
ActronAir logo will then be displayed for the next 5 - 10
seconds
Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
Defrost
10:20 Unit: Unit ON
System Screen (default) provides an overview of
system status, showing the Room Temperature, Supply
Temperature, Compressors, Reversing Valves ON/OFF
status and System Defrost indicator.
Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:20 Unit: Unit ON
Compressor 1 and Reversing Valve 1 are On. (System in
Heat Mode), first triangles are darkened
Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:20 Unit: Unit ON
Compressors 1 and 2 and Reversing Valves 1 and 2
are On. (Systems are in Heat Mode), all triangles are
darkened
NOTES
Displays for two compressors and reversing valves are shown above for illustration purposes only. The number of
compressors / reversing valves displayed will depend on the air conditioning system model.

Operation Manual CP05 / CP10 Controller
8Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
Compressor 1 Defrost Operation Compressor 2 Defrost Operation
1Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:20 Unit: Unit ON1
Normal Heating
Operation 1Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:26 Unit: Unit ON
Normal Heating
Operation
2Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:21 Unit: Unit ON
Defrost
Call for Defrost
System 1 2Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:27 Unit: Unit ON
Defrost
Call for Defrost
System 2
3Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:22 Unit: Unit ON
Defrost
Comp. 1 Off 3Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:27 Unit: Unit ON
Defrost
Comp. 2 Off
4Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:22 Unit: Unit ON
Defrost
Comp. 1 and
Rev. Valve 1 Off 4Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:27 Unit: Unit ON
Defrost
Comp. 2 and
Rev. Valve 2 Off
5Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:22 Unit: Unit ON
Defrost
Comp. 1 On
Rev. Valve 1 Off 5Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:28 Unit: Unit ON
Defrost
Comp. 2 On
Rev. Valve 2 Off
6Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:23 Unit: Unit ON
Defrost Complete 6Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:28 Unit: Unit ON
Defrost Complete
7Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:23 Unit: Unit ON
Comp. 1 and
Rev. Valve 1 Off 7Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:29 Unit: Unit ON
Comp. 2 and
Rev. Valve 2 Off
8Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:23 Unit: Unit ON
Comp. 1 Off
Rev. Valve 1 On 8Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:29 Unit: Unit ON
Comp. 2 Off
Rev. Valve 2 On
9Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:26 Unit: Unit ON
Normal Heating
Operation 9Room T. : 23.7oC
oC
Supply T. :
Comp Rev Vlv
10:32 Unit: Unit ON
Normal Heating
Operation

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
9
Operation Manual CP05 / CP10 Controller
. Menu Tree
CONSUMER / END USER MEN
Main Menu
D. Clock / Scheduler
D1. Set the Day, Date, Time,
Scheduler - Enable / Disable
D7. After Hours Duration Setting
D8-D19. Special Days Setting
D3-D6. 7 Days Schedule Start / End
D2. Day Light Saving Time
Enable / Disable
Auto Change Over
C1. Operation Mode
Mode
Fan Speed (Optional 3-Speed)
Fan Mode
Cool Only
Low
Continuous
High
Heat Only
Medium
Auto Cycle
C. Mode of Operation
50+oC
10oC
-
Log 100 - Recent Alarm
F. Alarm History
Log 1 - Recent Alarm
Reset Alarm Log
UP TO
E9. Supply Fan Speed Status
Condenser Fan Speed Status
Economy Cycle Output Status
E10-E12. Ref. Circuit (1,2 and 3)
Compressor Status
Reversing Valve Status
Cond Fan Low Spd Status
Cond Fan Hi Speed Status
E. Status
E5. Demand Management 1
Demand Management 2
Demand Management 3
A/Hours Input Status
E6. HP Status
LP Status
A. On / Off Unit
A1. Turn Unit - ON / OFF / FAN ONLY
A2. Display Backlight - Auto / ON / OFF
B. Setpoint
B1. Room Temperature Setpoint
Temp. Setback - Enable / Disable
Note: To scroll Up or Down from existing menu,
press or Button.
E1-E3. Disch Temp (Crt 1,2 and 3)
OD Coil Temp (Crt 1 and 2)
Room Temp
CO2Sensor
Outside Air Temp
External ID Fan Speed Status
External Capacity Status
E13. Output 8: On/Off
E14. Indoor Fan Board
Indoor Fan 1: On/Off
Indoor Fan 2 On/Off
Supply Fan 1: PWM
Supply Fan 2: PWM
Aux Relay ON/OFF
E15. Indoor Fan Board
Anti-freeze Level 1, 2, 3 On/Off
E26. Indoor Fan Board
Current Mode:
Unit Select:
E27. Minimum Outside Position
Internal/BMS/CO2 Sensor
Economy Output (%)
Damper Command (V)
E8. Digital Inputs
Indoor Fan Board
Fan Fault, Dip Switches
E7. Stage 1, 2 and 3 Call
Heat Mode Call
E4. Indoor coil temp
Room Temp
Indoor 0-10V in
Indoor Pot val.
Indoor Current
E28. RS485 Outside Probe*
Temperature/Humidity
Dew Point/Enthalpy
E29. RS485 Room Probe*
Temperature/Humidity
Dew Point/Enthalpy
*Available when enabled via Service Menu.

Operation Manual CP05 / CP10 Controller
10 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
. Sub Menu Level Descriptions
A. On/Off Unit Sub-Menu
Menu screen to Turn ON / OFF the unit.
Sub-Menu Level Indicator
(Level 1 of 8 levels)
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Sub-Menu Title
(Description)
B. Setpoint Sub-Menu
Menu screen to set the setpoint temperature / setback temperature.
A. On / O󰀨 Unit
B. Setpoint
Main Menu B
C. Mode of Operation
C. Mode of Operation Sub-Menu
Menu screen for selection of COOL, HEAT or AUTO CHANGEOVER operation.
B. Setpoint
Main Menu C
C. Mode of Operation
A. On / O󰀨 Unit
D. Clock/Scheduler Sub-Menu
Menu screen to set the date and time.
C. Mode of Operation
B. Setpoint
Main Menu D
D. Clock / Scheduler
E. Status Sub-Menu
Read only Menu screen to view the unit running conditions, such as
Room Air temperature, Fan Speed, Outside temperature, LP/HP, Discharge
Temperature, OD Fan Speed, etc...
C. Mode of Operation
Main Menu E
D. Clock /Scheduler
E. Status
F. Alarm History Sub-Menu Level
Read only Menu screen that indicates the alarm history
F. Alarm History
Main Menu F
D. Clock / Scheduler
E. Status
NOTE
Only up to level 6 covered by this manual are accessible by the end user.

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
11
Operation Manual CP05 / CP10 Controller
. Turn On /Off
O n / O 󰀨 U n i t A 1
ON OFF
FAN ONLY
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted Sub-Menu A1. On / Off Unit.
2. Press Button to enter Sub-Menu A1. On / Off Unit. Display will show the On/Off Unit page with switch symbol
pointing towards OFF position, indicating the unit is Turned-Off. (Symbol will be pointing towards ON position when
the unit is Turned-ON or FAN ONLY when the unit is running in FAN ONLY mode.
TO TURN-ON THE UNIT
3. Press Button, the cursor will appear and start blinking near ON.
4. Press or Button to select switch ON position. Display will show the On/Off Unit page with switch symbol pointing
towards ON and the cursor will still be blinking.
5. Press (Enter) Button to Turn-On the unit. The cursor will disappear and the unit will Turn-On.
TO TURN-OFF THE UNIT / SELECT FAN ONLY MODE
6. Repeat Steps 1 and 2, then press Button, cursor will appear and start blinking near ON.
7. Press or Button to select switch OFF or FAN ONLY position. Display will show the On/Off Unit page with switch
symbol pointing towards OFF or FAN ONLY and the cursor will still be blinking .
8. Press Button to Turn-Off the unit or switch to the FAN ONLY mode. The cursor will disappear and the unit will Turn-
Off or switch to FAN ONLY mode.
TO RETURN TO THE MAIN MENU
9. Press (Escape / Return) Button twice to return to the Main Menu. Otherwise press Button.
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Men A
C. Mode of Operation
On / O󰀨 Unit A1
ON OFF
FAN ONLY
On / O󰀨 Unit A1
ON OFF
FAN ONLY FAN ONLY
On / O󰀨 Unit A1
ON OFF
Step 1 Step 2 Step 3 Step 4
FAN ONLY
On / O󰀨 Unit A1
ON OFF
FAN ONLY
On / O󰀨 Unit A1
ON OFF
On / O󰀨 Unit A1
ON OFF
FAN ONLY FAN ONLY
On / O󰀨 Unit A1
ON OFF
Step 5 Step 6 Step 7
On / O󰀨 Unit A1
ON OFF
FAN ONLY FAN ONLY
On / O󰀨 Unit A1
ON OFF
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 8 Step 9

Operation Manual CP05 / CP10 Controller
12 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
. Backlight
Display Backlight : AUTO
On / O󰀨 Unit A2
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted Sub-Menu A. On / Off Unit.
2. Press Button to enter Sub-Menu A. On / Off Unit.
3. Press or Button to get into the Display Backlight sub-level menu.
4. Press Button to select the Display Backlight page and the cursor will appear on the first letter of the current
display backlight setting.
5. Press or Button to select the backlight setting from either AUTO, ON or OFF.
6. Press Button to lock-in the selected display backlight setting and the cursor will disappear. The backlight will
immediately Turn ON / OFF, depending on the selected mode.
NOTES
On AUTO mode, the Backlight will Turn Off in 5 minutes after the last button is pressed.
Backlight will instantly Turn ON / OFF when either of the mode is selected.
TO RETURN TO THE MAIN MENU
7. Press (Escape / Return) Button twice to return to the Main Menu. Otherwise press Button.
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
On / O󰀨 Unit A1
ON OFF
FAN ONLY
On / O󰀨 Unit A2
Display Backlight : AUTO
On / O󰀨 Unit A2
Display Backlight : AUTO
Step 1 Step 2 Step 3 Step 4
On / O󰀨 Unit A2
Display Backlight : ON
On / O󰀨 Unit A2
Display Backlight : OFF
On / O󰀨 Unit A2
Display Backlight : ON A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 5 Step 6 Step 7

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
13
Operation Manual CP05 / CP10 Controller
. Setting Room Temperature Setpoint
Setpoint : 23.0oc
Temperature setback :
DISABLE
Setpoint B1
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted Sub-Menu A. On / Off Unit.
2. Press Button to scroll down to B. Setpoint sub-menu.
3. Press Button to enter B. Setpoint sub-menu. Room setpoint (room set point temperature) screen will appear.
4. Press Button cursor will appear and blink next to the setpoint temperature.
5. Press or Button to change room temperature setting.
NOTES
Temperature setpoint can be changed with an incremental/decremental value of 0.1°C.
6. Press Button to lock-in your desired room set point temperature. The cursor will disappear and the new room
setpoint temperature will be displayed.
TO RETURN TO THE MAIN MENU
7. Keep pressing (Escape / Return) Button until you get to the Main Menu screen. Otherwise press Button.
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
A. On / O󰀨 Unit
B. Setpoint
Main Menu B
C. Mode of Operation
Setpoint : 23.0oc
Temperature setback :
DISABLE
Setpoint B1
Setpoint : 23.0oc
Temperature setback :
DISABLE
Setpoint B1
Step 1 Step 2 Step 3 Step 4
Setpoint : 22.9oc
Temperature setback :
DISABLE
Setpoint B1
Setpoint : 23.1oc
Temperature setback :
DISABLE
Setpoint B1
Setpoint : 23.0oc
Temperature setback :
DISABLE
Setpoint B1
A. On / O󰀨 Unit
B. Setpoint
Main Menu B
C. Mode of Operation
Step 5 Step 6 Step 7
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 7

Operation Manual CP05 / CP10 Controller
14 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
. Setting The Temperature Setback
Setpoint : 22.0oc
Temperature setback :
Cooling Limit : 25.0oc
Heating Limit : 18.0oc
ENABLE
Setpoint B1
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted Sub-Menu A. On / Off Unit.
2. Press Button to scroll down to B. Setpoint sub-menu.
3. Press Button to enter B. Setpoint sub-menu. Room setpoint (room set point temperature and temperature setback)
screen will appear.
4. Press Button twice and the cursor will appear and blink next to temperature setback DISABLE prompt.
5. Press or Button to change the temperature setback prompt from DISABLE to ENABLE.
6. Press Button to enable temperature setback function and the cursor will move next to the cooling temperature
setback setting.
7. Press or Button to change the cooling temperature setback setting.
NOTES
Temperature can be changed with an incremental/decremental value of 0.1°C.
Cooling temperature setback can be selected between 26°C to 30°C.
8. Follow steps 6 and 7 above, to set the heating temperature setback.
NOTE
Heating temperature setback can be selected between 10°C to 20°C
TO RETURN TO THE MAIN MENU
9. Keep pressing (Escape/Return) Button until you get to the Main Menu screen. Otherwise press Button.
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
A. On / O󰀨 Unit
B. Setpoint
Main Menu B
C. Mode of Operation
Setpoint : 22.0oc
Temperature setback :
DISABLE
Setpoint B1
Setpoint : 22.0oc
Temperature setback :
DISABLE
Setpoint B1
Step 1 Step 2 Step 3 Step 4
Setpoint : 22.0oc
Temperature setback :
ENABLE
Setpoint B1
Setpoint : 22.0oc
Temperature setback :
ENABLE
Setpoint B1
Setpoint : 22.0oc
Temperature setback :
Cooling Limit : 25.0oc
Heating Limit : 18.0oc
ENABLE
Setpoint B1
Setpoint : 22.0oc
Temperature setback :
Cooling Limit : 24.9oc
Heating Limit : 18.0oc
ENABLE
Setpoint B1
Step 5 Step 6 Step 7
Setpoint : 22.0oc
Temperature setback :
Cooling Limit : 24.9oc
Heating Limit : 18.0oc
ENABLE
Setpoint B1
Setpoint : 22.0oc
Temperature setback :
Cooling Limit : 25.0oc
Heating Limit : 18.0oc
ENABLE
Setpoint B1
A. On / O󰀨 Unit
B. Setpoint
Main Menu B
C. Mode of Operation
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 7 Step 8 Step 9

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
15
Operation Manual CP05 / CP10 Controller
. Operation Mode
CHANGING THE MODE OF OPERATION
Operation Mode C1
Fan mode: Auto cycle
Mode: COOL ONLY
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted Sub-Menu A. On / Off Unit.
2. Press Button to scroll down to C. Mode of Operation sub-menu.
3. Press Button to go into C. Mode of Operation sub-menu. Display will change to Operation Mode and Fan Mode
selection menu, showing the current Mode and Fan mode.
NOTE
For Optional 3 Speed Fan Operation, Fan Speed will be shown and can be selected via the service menu (See Display
Progression Step 3A below).
4. Press Button to change the mode and the cursor will be blinking at the first letter of the current mode.
TO SELECT COOL ONLY MODE (from HEAT ONLY mode)
5. Press or Button to scroll to COOL ONLY mode. Display will show COOL ONLY mode with the cursor still blinking.
6. Press Button to select COOL ONLY mode, the cursor will move to the next menu item indicating that the operation
is now in COOL ONLY mode.
NOTES
• Mode of Operation menu will be locked for 3 min after changing mode as a safety time delay in order to prevent
frequent mode changes.
• To select HEAT ONLY or AUTO CHANGE OVER mode, follow steps 4 to 6 above.
CHANGING THE FAN MODE
7. Follow steps 1 to 4 above and then press Button to get into the FAN mode selection menu. The will be blinking at
the first letter of the current FAN mode setting.
8. Press or Button to select AUTO CYCLE or CONTINUOUS FAN mode.
9. Press Button to lock-in your desired FAN mode.
CHANGING THE FAN SPEED (For 3 Speed Fan Operation, when applicable)
10. Follow steps 1 to 4 above and then press Button to get into the Fan Speed selection menu. The will be blinking at
the first letter of the current Fan Speed setting.
11. Press or Button to select LOW, MED or HIGH fan speed.
12. Press Button to lock-in your desired Fan Speed.
TO RETURN TO THE MAIN MENU
13. Keep pressing (Escape / Return) Button until you get to the Main Menu screen. Otherwise press Button.

Operation Manual CP05 / CP10 Controller
16 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
B. Setpoint
Main Menu C
C. Mode of Operation
A. On / O󰀨 Unit
Heat / Cool C1
Mode : AUTO CHANGE OVER
Fan mode : Continuous
Heat / Cool C1
Mode : AUTO CHANGE OVER
Fan Speed : MED.
Fan mode : Continuous
Step 1 Step 2 Step 3 Step 3A *
Heat / Cool C1
Mode : AUTO CHANGE OVER
Fan mode : Continuous
Heat / Cool C1
Mode : HEAT ONLY
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Continuous
Step 4 Step 5 Step 6
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Auto Cycle
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan mode : Auto Cycle
Step 7 Step 8 Step 9
Heat / Cool C1
Mode : COOL ONLY
Fan Speed : LOW
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan Speed : MED.
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan Speed : HIGH
Fan mode : Continuous
Heat / Cool C1
Mode : COOL ONLY
Fan Speed : MED.
Fan mode : Continuous
Step 10 Step 12
Heat / Cool C1
Mode : COOL ONLY
Fan Speed : MED.
Fan mode : Continuous
B. Setpoint
Main Menu C
C. Mode of Operation
A. On / O󰀨 Unit A. On / O󰀨 Unit
B. Setpoint
Main Menu AA
C. Mode of Operation
Step 12 Step 13
*For Optional 3 Speed Fan Operation, when applicable (See Display Progression Step 3A above).
. Setting The Clock
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
1. Press Button to get into the Main Menu. Display will show Main Menu and highlighted A. On / Off Unit main menu.
2. Press Button to scroll down to D. Clock / Scheduler main menu.
3. Press Button to enter D. Clock/ Scheduler main menu. Display will show the Day, Date, Hour page and Enable
Scheduler status.
4. Press Button and the cursor will appear next to the date indicator and the corresponding day will be shown,
i.e. Monday, 22/09/14 (22nd September 2014 ).
5. Press or Button to change the date.
NOTE
Day changes corresponding to the change in date as follows:
Sunday, 21/09/14 (21st September 2014),
Tuesday, 23/09/14 (23rd September 2014).

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
17
Operation Manual CP05 / CP10 Controller
6. Press Button to lock-in the Date and the cursor will move next to the month indicator.
7. Press or Button to change the month.
NOTE
Day changes corresponding to the change in month as follows:
Friday, 22/08/14 (22nd August 2014),
Wednesday, 22/10/14 (22nd October 2014).
8. Press Button to lock-in the Month and the cursor will move next to the year date.
9. Press or Button to change the year.
NOTE
Day changes corresponding to the change in year as follows:
Sunday, 22/09/13 (22nd September 2013),
Tuesday, 22/09/15 (22nd September 2015).
Display Progression
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
C. Mode of Operation
B. Setpoint
Main Menu D
D. Clock / Scheduler
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Step 1 Step 2 Step 3 Step 4
Hour: 10:27
Enable Scheduler: No
Date: 21 / 09 / 14
Day: Sunday
Clock D1
Hour: 10:27
Enable Scheduler: No
Date: 23 / 09 / 14
Day: Tuesday
Clock D1
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:27
Enable Scheduler: No
Date: 22 / 08 / 14
Day: Friday
Clock D1
Step 5 Step 6 Step 7
Hour: 10:27
Enable Scheduler: No
Date: 22 / 10 / 14
Day: Wednesday
Clock D1
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 13
Day: Sunday
Clock D1
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 15
Day: Tuesday
Clock D1
Step 7 Step 8 Step 9
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
10. Press Button to lock-in the Year and Date and the cursor will move next to the hour indicator.
11. Press or Button to change the hour.
12. Press Button to lock-in the hour and the cursor will move next to the minute indicator.
13. Press or Button to change the minute.
14. Press Button to lock-in the minute and the cursor will disappear.

Operation Manual CP05 / CP10 Controller
18 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
TO RETURN TO THE MAIN MENU
15. Keep pressing (Escape / Return) Button until you get to the Main Menu screen. Otherwise press Button.
Display Progression
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 09:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 11:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Step 10 Step 11 (09:28) Step 11 (11:28) Step 12
Hour: 10:27
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:29
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
Hour: 10:28
Enable Scheduler: No
Date: 22 / 09 / 14
Day: Monday
Clock D1
C. Mode of Operation
B. Setpoint
Main Menu D
D. Clock / Scheduler
Step 13 (12:56) Step 13 (12:58) Step 14 Step 15
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 15
NOTE
Use the or Button to toggle on the D. Clock / Scheduler sub-menu functions.
. Daylight Saving Time Enable
Clock D2
DST: ENABLE
Transition time: 60min
Start: FIRST SUNDAY
End: FIRST SUNDAY
in OCTOBER at 2.00
in APRIL at 2.00
1. From the main menu, scroll down to D. Clock / Scheduler menu following the procedures from Setting the Clock
section.
2. Press Button to enter D. Clock/ Scheduler main menu.
3. Press Button to scroll down to Daylight Saving Time sub-menu.
4. Press Button to enter Daylight Saving Time sub-menu and the cursor will appear on ENABLE indicator. If the
indicator shows DISABLE, press Button to change to ENABLE.
5. Press Button again to enable Daylight Saving Time mode and the cursor will move to the Transition time segment.
6. Press or Button to select the number of minutes for transition into daylight saving time.
NOTE
The transition time can be set in 1 minute increment up to 60 minutes maximum.
7. Press Button to lock-in the selected length of transition time, i.e. 60min. The cursor will next move to the order of
the week (First, Second, etc..) for the start of transition to occur.
8. Press or Button to select the First, Second, Third, Fourth or Last for transition into daylight saving time, e.g. FIRST.
9. Press Button to lock-in FIRST and the cursor will next move to the Day for the start of the transition to occur.

Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
19
Operation Manual CP05 / CP10 Controller
Display Progression
C. Mode of Operation
B. Setpoint
Main Menu D
D. Clock / Scheduler
Clock D2
DST: ENABLE
Transition time: --- min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: --- min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: --- min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Step 1 Step 2 Step 3 Step 4
Clock D2
DST: ENABLE
Transition time: 01 min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: --- --- ---
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Step 5 Step 6 Step 7
Clock D2
DST: ENABLE
Transition time: 60 min
Start: LAST SUNDAY
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in --- --- --- at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in JANUARY at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at --- .00
End: --- --- ---
in --- --- --- at --- .00
Step 7 Step 8 Step 9 (January) Step 9 (October)
Clock D2
DST: ENABLE
Transition time: 60min
Start: FIRST SUNDAY
End: FIRST SUNDAY
in OCTOBER at 2.00
in APRIL at 2.00
10. Press or Button to select the Day for transition into daylight saving time, e.g. SUNDAY.
11. Press Button to lock-in Sunday for the transition to occur, i.e. FIRST SUNDAY. The cursor will next move to the
starting month selection segment.
12. Press or Button to select the Month for transition into daylight saving time.
13. Press Button to lock-in the Month for transition to occur, i.e. October. The cursor will next move to the starting
time selection segment.
14. Press or Button to select the hour on Sunday for transition into daylight saving time.
NOTE
The time clock is in 24:00 format, i.e. 2:00 AM will be 2.00 and 8:00 PM will be 20.00.
15. Press Button to lock-in the time on the FIRST SUNDAY for transition to occur, i.e. 2.00. The cursor will next move to
the transition to end condition of Daylight Saving Time.
16. Repeat steps 8- 15 to set up the end of Daylight Saving Time parameters.
17. Press Button to enable the Daylight Saving Time and lock-in the parameters.

Operation Manual CP05 / CP10 Controller
20 Installation and Commissioning Guide - Split Ducted Outdoor Unit
Doc. No. 0525-031 Ver. 4 210309
TO RETURN TO THE MAIN MENU
18. Keep pressing (Escape / Return) Button until you get to the Main Menu screen. Otherwise press Button.
Display Progression
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at --- .00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 2.00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 16.00
End: --- --- ---
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 2.00
End: --- --- ---
in --- --- --- at --- .00
Step 10 Step 11 (2.00) Step 11 (16.00) Step 12
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 2.00
End: FIRST SUNDAY
in --- --- --- at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 2.00
End: FIRST SUNDAY
in APRIL at --- .00
Clock D2
DST: ENABLE
Transition time: 60 min
Start: FIRST SUNDAY
in OCTOBER at 2.00
End: FIRST SUNDAY
in APRIL at 3.00
C. Mode of Operation
B. Setpoint
Main Menu D
D. Clock / Scheduler
Step 13 Step 14 Step 15
A. On / O󰀨 Unit
B. Setpoint
Main Menu A
C. Mode of Operation
Step 15
NOTE
Use the or Button to toggle on the D. Clock / Scheduler sub-menu functions.
. Daylight Saving Time Disable
Clock D2
DST: DISABLE
Transition time: - - - min
Start: - - - - - - - - -
End:
in - - - - - - - - - at - - - .00
in - - - - - - - - - at - - - .00
1. From the main menu, scroll down to D. Clock / Scheduler menu following the procedures from Setting the Clock
section.
2. Press Button to enter D. Clock / Scheduler main menu.
3. Press Button to scroll down into Daylight Saving Time sub-menu.
4. Press Button to enter Daylight Saving Time sub-menu and the cursor will appear on ENABLE indicator.
5. Press or Button to select the DISABLE Daylight Saving Time function.
NOTE
The segment will change from ENABLE to DISABLE.
6. Press Button to disable the Daylight Saving Time function. The cursor will disappear and the DISABLE sub-menu
screen will be displayed.