ADC ADSCOPE 600 User manual

Instructions for Use
Adscope®Stethoscope

2
Thank you for choosing an ADC®ADSCOPE®Stethoscope. Your new ADC®ADSCOPE®
stethoscope is designed to provide unsurpassed acoustic sensitivity, unrivalled durability,
and unparalleled comfort. Every component has been carefully designed to maximize
performance.
Device Description and Intended Use
This device is intended for medical diagnostic purposes only. It can be used for listen-
ing to heart, lung and other body sounds as well as for normal auscultation. The de-
vice is not designed, sold or intended for use except as indicated.
General Warnings A warning stat m nt in this manual id ntifi s a
condition or practic which, if not corr ct d or discontinu d imm diat ly,
could l ad to pati nt injury, illn ss, or d ath.
CAUTION:
Never use stethoscope without eartips firmly locked in place.
WARNING: Stethoscope contains small parts which may present a choking hazard.
Faceplates and accessories should be kept out of the reach of children.
Selection of the Chestpiece (AFD Models - 600, 601, 603, 604, 606, 608,
612, 614, 615, and 618)
The ADC®ADSCOPES®with AFD Technology provide the enhanced acoustic re-
sponse of a traditional bell and diaphragm in a convenient one-sided chestpiece. A
rubber gasket around the perimeter of the diaphragm allows you to alter the frequency
response by changing the contact pressure.
(Fig. 1) (Fig. 2)
For low frequency response (bell phase)
simply hold the chestpiece in place with
light pressure. (Fig. 1)
For high frequency monitoring (diaphragm
phase) apply firm fingertip pressure on the
sculpted finger rest. (Fig. 2)
!

3
Selection of the Combination Chestpiece
(Traditional 2-sided Model)
On ADC
®
ADSCOPE
®
combination stethoscopes you can se-
lect the use of either the diaphragm for monitoring high fre-
quency sounds, or the open bell for monitoring low frequency
response.
To select a side, hold the chestpiece valve stem in one hand
and rotate the chestpiece 180° with the other hand until it
“clicks” into place. The stem has an engraved dot, confirming
the activated side when it faces either the bell or diaphragm.
To confirm which side is activated, tap lightly on one side,
then the other, to hear which provides the positive response.
Converting the Chestpiece (601, 608 Only)
The 601 and 608 chestpiece drums accommodate 2 dif-
ferent chestpiece attachments of your choice. To attach
the bell you must first remove the pediatric diaphragm
and then thread the bell clockwise until tight.
To remove pediatric diaphragm, twist in a counterclock-
wise direction.
Orientation of the Headset
The binaurals (eartubes) are angled at 15° to per-
mit a comfortable, acoustically sealed aural fit.
Eartips should point forward, towards the bridge of
the nose to fit properly.
Correct Incorrect
Diaphragm Activated
Bell Activated

4
Adjusting the Spring Tension in the Headset
To reduce the tension, grip the binaurals firmly
using both hands with fingers at the center of the
“Y” in the tubing, thumbs at each side where
the tubing branches out. Flex bin aurals gradu-
ally until the desired tension is obtained.
To increase the tension, grip the binaurals in the
hand and squeeze the binaural tubes together
gradually.
CAUTION: Excessive adjustment could weaken the spring.
Shortening the Tube Length (Clinician Models ONLY)
Clinician Series Adscopes are equipped with 22” tubing.
If a shorter length is desired, remove the chestpiece from
tubing. Cut tubing to desired length with a sharp single edge
razor on a hard surface. To soften tubing, use a hair dryer on
a low heat setting for approximately one minute, and reinsert
chestpiece stem in tubing.
CAUTION: Allow tubing to cool before using.
Replacing the Diaphragm
Select ADSCOPES®are equipped with up to two ultrasensitive, yet
extremely durable diaphragms. It is unlikely that they will ever
need replacement.
Snap-on (PVC) Rim: Snap off the rim and remove the worn di-
aphragm. Replace with new diaphragm and reattach rim by gently
stretching rim until the chestpiece edge inserts fully in the track
within the rim.
Thr ad d (M tal) Rim: Turn rim counterclockwise to remove.
Replace with new diaphragm and reattach rim by turning clock-
wise until tight to re-assemble.
DO NOT
trim th s
mod ls
OK TO
trim th s
mod ls
To r duc t nsion To incr as t nsion

5
Replacing Faceplates (618 Models)
R moval: Hold the chestpiece with one hand.
Pop off the old plate diagonally from behind.
R plac : Position the bottom of the new plate to the socket of the
chestpiece. Snap the top firmly into place.
Replacing Eartips
To r plac AdsoftTM Plus Eartips: Slide AdsoftTM PL S eartip over adapter until it
locks tight into internal channel. Repeat steps for second aural tube.
Cleaning, Disinfection, and Storage
• Clean your Adscope between patients using either a 70% isopropyl alcohol
solution, 70% isopropyl alcohol wipe, or disposable wipe with soap and water.
Be sure to wipe down all surfaces including chestpiece, tubing, headset and eartips.
• The diaphragm, non-chill bell ring, and eartips may be removed for a thorough
cleaning if desired. Ensure all parts are thoroughly dry before reassembling.
Do not remove chestpiece.
• If storing in original box, the molded tray (all models except 609) may also be
wiped down to reduce risk of re-contamination.
• Avoid extreme heat, cold, solvents or oils.
• Do not leave exposed to direct sunlight for prolonged periods of time.
• Periodically check that eartips are securely affixed to the headset and freefrom
dam-age.
• Do not immerse stethoscope in any liquid.
• Do not steam sterilize. If sterilization is necessary gas sterilize only.