ADTRAN Job Aid+ 1442804G1 User manual

jobAid
DESCRIPTION
TheSmallForm‐FactorPluggable(SFP)3.125GigabitEthernet4
kmisasinglemodefiberSFPthatplugsintoamoduledesigned
toacceptSFPs.TheSFPprovidesadualopticalinterfacetothe
3.125GigabitEthernetphysicalinterface.Installedintoanappro‐
priatemodule,theSFPprovides3.125GigabitEthernetinterface
tothesupportingsystem.
NOTE
ThisSFPshouldnotbeusedinapplicationsrequiringstandard
Gigabit(1000Base)Ethernetservices.
ThefollowingfeaturesaresupportedontheSFP:
♦3.125GigabitEthernetdatarate
♦1310nmTransmitter
♦Wavelength:1310nm
♦Opticaldistance:4kmmaximum
CAUTION
!
Duetocompliancecertificationrequirements,onlySFPssupplied
byADTRANshouldbeused.ADTRANcannotcertifysystem
integritywithotherSFPs.
Operational Specifications
♦OpticalSpecifications:
◊Opticaltransmitlevel:–8.4dBmto–3dBm
◊Opticalreceivelevel:–18dBm
◊Opticalconnectors:LC
◊SFF8472Digitaldiagnosticcompliant
◊CompatiblewithSFPMSA
♦ExtendedEnvironmentalSupport:
◊Operationaltemperaturerange:–40°Cto+85°C
◊Storagetemperaturerange:–40°Cto+85°C
◊Relativehumidityto95%,noncondensing
Small Form-Factor Pluggable
3.125 Gigabit Ethernet 4 km
INSTALLATION
Priortoinstallation,inspecttheSFP.Ifdamagehasoccured
duringshipping,fileaclaimwiththecarrier,andthencontact
ADTRANCustomerSupport.Formoreinformation,referto
“Warranty”.
ToinstalltheSFPintoanappropriatemodule,completethe
followingsteps:
1. DonotremovetheprotectiveendcapfromtheSFPuntilthe
fiberopticcableisreadytobeconnected.
2. InserttheSFPintotheSFPcageonthemodule.Ensurethe
manufacturer’slabelontheSFPisfacingupwardforcorrect
installation.
3. SlidetheSFPallthewayintothereceptacleuntilthereisan
audible“click”.
NOTE
ThelatchontheSFPisusedtoremovetheSFPfromthecageon
thecircuitcard
SAFETY AND REGULATORY COMPLIANCE
CAUTION
!
ElectrostaticDischarge(ESD)candamageelectronicmodules.
Whenhandlingmodules,wearanantistaticdischargewriststrap
topreventdamagetoelectroniccomponents.Placemodulesin
antistaticpackingmaterialwhentransportingorstoring.When
workingonmodules,alwaysplacethemonanapproved
antistaticmatthatiselectricallygrounded.
CAUTION
C
TheSFPisaClass1LaserProductandcomplieswiththeLaser
SafetyrequirementsofFDA21CFR1040.10and1040.11,and
EN60825‐1and‐2.TheSFPisNRTLListedandCBCertifiedtoall
applicableAmericanandEuropeansafetystandards.
TheSFPmeetsorexceedsalltheapplicablerequirementsof
NEBS,TelcordiaGR‐63‐CORE,andGR‐1089‐CORE.TheSFPis
intendedfordeploymentinCentralOfficetypefacilities,EEEs,
EECs,andlocationswheretheNECapplies(forexample,
CustomerPremises).TheSFPistobeinstalledinADTRAN
productsinRestrictedAccessLocationsonly,andinstalledby
trainedservicepersonnel.
ThisdevicecomplieswithPart15oftheFCCrules.Operationis
subjecttothefollowingtwoconditions:
1. Thisdevicemaynotcauseharmfulinterference
2. Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
ChangesormodificationsnotexpresslyapprovedbyADTRAN
couldvoidtheuserʹsauthoritytooperatethisequipment.
CLEI: BVL3ADND_ _
Product P/N: 1442804G1
Issue Date: December 2010
Document P/N: 61442804G1-22B

C A U T I O NC A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2010 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442804G1-22B*
CAUTION
!
♦ PerGR‐1089‐COREtheADTRANsystemthattheSFPisbeing
deployedinisdesignedandintendedforinstallationaspartof
aCommonBondingNetwork(CBN).TheADTRANsystem
thattheSFPisbeingdeployedinisnotdesignednorintended
forinstallationaspartofanIsolatedBondingNetwork(IBN).
♦ PerGR‐1089‐CORESection9,theSFPdoesnothaveaninternal
DCconnectionbetweenbatteryreturnandframeground.The
SFPcanbeinstalledinaDC‐I(isolated)orDC‐C(common)
installation.Forinstallationswhereothercardsorthehost
systemhaveinternalconnectionsbetweenbatteryreturnand
frameground,thesystemwouldbeintendedfordeployment
onlyinaDC‐Cinstallation.
♦ TheADTRANsystemchassisframegroundterminalmustbe
connectedtoareliableearthgroundtoensurethatthemetal
enclosureoftheSFPisproperlygroundedviathebackplane
connector.
NOTE
The3.125GigabitEthernetport(s)areopticalandthereforeare
notclassifiedasanytypeofportasdefinedinAppendixBofGR‐
1089‐COREIssue4.
TheSFPisdesignedtomeetthefollowingenvironmentalclasses:
♦ETSIEN300019‐1‐1“Classificationofenvironmental
conditions;Storage,”Class1.2
♦ETSIEN300019‐1‐2“Classificationofenvironmental
conditions,Transportation,”Class2.3
♦ETSIEN300019‐1‐3“Classificationofenvironmental
conditions,Stationaryuseatweather‐protectedlocations,”
Class3.3
Theequipmentisdesignedtofunctionwithoutdegradation
duringexposuretoalltestseveritiesperClass3.3.