ADTRAN jobAid+ SFP+ 11.3 G BIDI 20KM User manual

jobAid
1
DESCRIPTION
The SFP+ 11.3 G BIDI 20KM modules plug into ADTRAN
equipment designed to accept Small Form-factor Pluggables
(SFPs). Installed into an appropriate host unit, the SFP+ BIDI
provides a 10G optical interface to the supporting system.
This Job Aid supports the following SFP+ Modules:
NOTE
■The 1442422F1 and 1442422F2 must be deployed as pairs at
each end of the network. The 1442422F1 must be connected to
the 1442422F2 at the other end of the fiber.
■To ensure compatibility, refer to the documentation provided
with the host module.
Part Number TX Wavelength RX Wavelength CLEI
1442422F1 1320-1340nm 1260-1280nm BVL3AYHD_ _
1442422F2 1260-1280nm 1320-1340nm BVL3AYGD_ _
Host
Unit
1442422F1 1442422F2
Host
Unit
Rx: 1260 to
1280 nm
Tx: 1320 to
1340 nm
Rx: 1320 to
1340 nm
Tx: 1260 to
1280 nm
Small Form-factor Pluggable
SFP+ 11.3 G BIDI 20KM
The following features are supported on the SFP+ BIDI:
■9.95 - 11.3 Gbps, single-fiber operation
■20 km maximum optical span
NOTICE
Due to compliance certification requirements, only SFP+ modules
supplied by ADTRAN are to be used with the host module.
ADTRAN cannot certify system integrity with other SFPs.
SPECIFICATIONS
■Power: Less than 1.5W
■Optical Specifications:
♦Data Rate: 9.95 to 11.3 Gbps
♦Optical Transmit Level: –4.2 dBm to +3.0 dBm
♦Optical Receive Level: –14.4 dBm to +0.5 dBm
♦Spectral Width: 1 nm maximum (20.0 dB Spectral Width)
♦Extinction Ratio: 3.5 dB minimum
♦SMSR: 30 dB minimum
♦Power Penalty: 1.0 dB
♦Optical Budget: 9.2 dB
♦Minimum Span Attenuation: 2.5 dB
♦Optical Span: 20 km
♦Optical connectors: LC
■Environmental:
♦Operational temperature range: –40°C to +85°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity to 95%, noncondensing
Product P/N: 1442422FX Issue Date: January 2015
Document P/N: 61442422FX-22B
Documentation for ADTRAN Carrier Networks products is
available for viewing and download directly from the
ADTRAN Support Community website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including
customized training and courses taught at our facilities or at
customer sites.
For inquiries, go to: http://adtran.com/training
The following related online documents and resources provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix (online tool: http://www.adtran.com/sfp)

261442422FX-22B
INSTALLATION
To install the SFP+ BIDI into an appropriate module, complete the
following steps:
1. Inspect the SFP+ BIDI. If damaged, file a claim with the car-
rier and then contact ADTRAN Customer Support.
CAUTION
!
Do not remove the protective end cap from the SFP+ until the
fiber optic cable is ready to be connected.
2. Insert the SFP+ BIDI into the SFP+ cage on the module.
Ensure that the manufacturer’s label on the SFP+ is facing
upward for correct installation.
3. Slide the SFP+ BIDI all the way into the receptacle until
there is an audible “click”.
NOTE
The latch on the SFP+ is used to remove the SFP+ from the cage
on the circuit card.
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1, IEC 60825-2, EN 60825-
1 and EN 60825-2.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
■Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) configuration. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the SFP is
properly grounded via the backplane connector.
NOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This SFP+ BIDI is compliant with SFF-8472 Digital Diagnostics
Monitoring Interface for Optical Transceivers, Revision 9.3
■This product is compliant with the SFP Multi-Source
Agreement (MSA).
■This product is designed to be deployed in GR-3108-CORE
environmental class 1, 2, and 3 as defined in GR-3108-CORE.
This product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, GR-1089-CORE, and ETSI EN
300368. This product is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises).
This product is to be installed in ADTRAN products in Restricted
Access Locations only, and installed by trained service personnel.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.

61442422FX-22B 3
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
■ETSI EN 300 019-1-1 Classification of environmental conditions;
Storage, Class 1.2
■ETSI EN 300 019-1-2 Classification of environmental conditions;
Transportation, Class 2.3
■ETSI EN 300 019-1-3 Classification of environmental conditions;
Stationary use at weather-protected locations, Class 3.3
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3 of ETSI EN 300
019-1-3.
This product complies with ETSI EN 300 386 “Electromagnetic
compatibility and Radio spectrum Matters (ERM); Telecommuni-
cation network equipment; Electromagnetic Compatibility (EMC)
requirements.”
The SFP+ BIDI meets EU RoHS Directive 2002/95/EC and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
FRANÇAIS
AVERTISSEMENT
!
Lisez tous les avertissements et mises en garde avant l’installation
de cet équipement ou la réalisation de toute opération de mainte-
nance.
ATTENTION
C
Ce produit utilise un module laser de classe 1 qui conforme aux
normes 21 CFR 1040.10, 1040.11 et IEC 60825-1 et -2. Pour assurer
la conformité aux normes mentionnées plus haut, seuls des
modules laser de classe 1 approuvés provenant d’une liste de
fournisseurs certifiés par ADTRAN (disponible sur le site
d’ADTRAN) doivent être installés sur ce produit. ADTRAN ne
peut certifier l’intégrité d’un système doté d’autres modules
laser..
ATTENTION
!
· Une L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
· La borne de mise à la terre du châssis doit être branchée à une
prise de terre afin d’assurer que le boîtier métallique de la SFP
est correctement mis à la terre grâce au connecteur de face
arrière.
Ce produit est conçu pour répondre aux classes environnemen-
tales suivantes :
■ETSI EN 300 019-1-1 "Classification des conditions
d'environnement; Entreposage," classe 1.2
■ETSI EN 300 019-1-2 "Classification des conditions
d'environnements; Transport," classe 2.3
■ETSI EN 300 019-1-3 "Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries," classe 3.3
L'équipement est conçu pour fonctionner sans dégradation lors
des tests à tous les niveaux de sévérité, suivant les spécifications
de la classe 3.3 de l'ETSI EN 300 019-1-3.
Cet appareil est conforme à la norme ETSI EN 300 386 " Compati-
bilité électromagnétique et spectre radioélectrique (ERM);
équipement des réseaux de télécommunications; exigences en
matière de compatibilité électromagnétique (CEM).
Ce produit est conforme à la directive européenne RoHS 2002/
95/CE et/ou aux exonérations applicables. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.

C A U T I O NC A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty: ADTRAN will replace or repair this product
within the warranty period if it does not meet its
published specifications or fails while in
service. Warranty information can be found
online at www.adtran.com/warranty.
©2015 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442422FX-22B*
DEUTSCH
WARNUNG
!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
VORSICHT
C
Dieses Produkt nutzt ein mit den Richtlinien 21 CFR 1040.10 und
1040.11 und IEC 60825-1 und -2 konformes Class 1 Lasermodul.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Class 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (erhältlich auf der Website von ADTRAN). ADTRAN
garantiert nicht für die Systemintegrität bei anderen
Lasermodulen.
VORSICHT
!
· Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
· Die Erdungsschiene des Rahmens muss an eine Bodenstation
angeschlossen werden, um sicherzustellen, dass das
Metallgehäuse des SFP vorschriftsmäßig über den
Rückwandanschluss geerdet ist.
Dieses Produkt wurde entsprechend der folgenden Umweltk-
lassen entwickelt:
■ETSI EN 300 019-1-1 "Klassifikation von Umweltbedingungen,
Lagerung," Klasse 1.2
■ETSI EN 300 019-1-2 "Klassifikation von Umweltbedingungen,
Transport," Klasse 2.3
■ETSI EN 300 019-1-3 "Klassifikation von Umweltbedingungen,
Stationärer Einsatz ohne Witterungseinflüsse," Klasse 3.3
Dieses Gerät funktioniert ohne Leistungsabfall während aller für
Klasse 3.3 von ETSI EN 300 019-1-3 vorgeschriebenen Belastung-
stests.
Dieses Produkt erfüllt die ETSI EN 300 386 Norm "Elektromagne-
tische Verträglichkeit und Funkspektrumangelegenheiten (ERM);
Einrichtungen des Telekommunikationsnetzes; Anforderungen
zur elektromagnetischen Verträglichkeit."
Dieses Produkt erfüllt die EU RoHS Richtlinie 2002/95/EC und/
oder gültige Ausnahmen. Bitte besuchen Sie www.adtran.com für
ausführlichere Informationen zu RoHS/WEEE.