ADTRAN Octal User manual

Octal and Quad FXO Modules
User Manual
Part Number 1200310L1 (Octal)
Part Number 1200329L1 (Quad)
61200310L1-1D
July 2000

901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
[phone]
© 2000ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.

iii
FCC regulations require that the following information be provided to the customer in this manual:
1. This equipment complies with Part 68 of the FCC rules. On the side or bottom of this equipment is
a label that contains, among other information, the FCC Registration Number an Ringer Equiva-
lence Number (REN), if applicable, for this equipment. If required, this information must be given
to the telephone company.
2. The following information may be required when applying to your local telephone company for
leased line facilities.
3. An FCC-compliant telephone cord with modular plug may be provided with this equipment. This
equipment is designed to be connected to the telephone network or premises wiring using a com-
patible modular jack which is FCC Part 68 compliant. See Chapter 2, Installation for details.
4. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
5. The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the proper operation of this equipment. If this happens, the telephone company
will provide advance notification and the opportunity to make the necessary modifications to
maintain uninterrupted service.
6. If experiencing difficulty with this equipment, please contact ADTRAN at [phone] for repair
or warranty information. If the equipment is causing harm to the network, the telephone company
may request this equipment to be disconnected from the network until the problem is resolved or
it is certain that the equipment is not malfunctioning.
7. This equipment contains no user serviceable parts.
8. The REN is used todetermine the quantity of devices which may be connected to the telephoneline.
Excessive RENs on the telephone line may result in the devices not ringing in response to an incom-
ing call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the
local telephone company.
Service Type REN/SOC FIC USOC
FXO (Loop Start) 0.1B/9.0F 02LS2 RJ11C
FXO (Ground Start) 0.1B/9.0F 02GS2 RJ11C

iv
Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio frequencies. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital appa-
ratus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003
of the Department of Communications.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils nume-
riques de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numeriques,”
NMB-003 edictee par le Ministre des Communications.
Change or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

v
Limited Product Warranty
ADTRAN warrants that for five (5) years from the date of shipment to Customer, all products manu-
factured by ADTRAN will be free from defects in materials and workmanship. ADTRAN also war-
rants that products will conform to the applicable specifications and drawings for such products, as
contained in the Product Manual or in ADTRAN's internal specifications and drawings for such prod-
ucts (which may or may not be reflected in the Product Manual). This warranty only applies if Cus-
tomer gives ADTRAN written notice of defects during the warranty period. Upon such notice,
ADTRAN will, at its option, either repair or replace the defective item. If ADTRAN is unable, in a rea-
sonable time, to repair or replace any equipment to a condition as warranted, Customer is entitled to a
full refund of the purchase price upon return of the equipment to ADTRAN. This warranty applies
only to the original purchaser and is not transferable without ADTRAN's express written permission.
This warranty becomes null and void if Customer modifies or alters the equipment in any way, other
than as specifically authorized by ADTRAN.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING CONSTITUTES
THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE EXCLUSIVE LIABILITY OF
ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES (EXPRESSED OR IMPLIED).
ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING (WITHOUT LIM-
ITATION), ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THIS
EXCLUSION MAY NOT APPLY TO CUSTOMER.
In no event will ADTRAN or its suppliers be liable to Customer for any incidental, special, punitive,
exemplary or consequential damages experienced by either Customer or a third party (including, but
not limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for
damages for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the
amount paid for the item. Some states do not allow the limitation or exclusion of liability for incidental
or consequential damages, so the above limitation or exclusion may not apply to Customer.
Warranty and Customer Service
ADTRAN will replace or repair this product within five years from the date of shipment if the product
does not meet its published specification, or if it fails while in service. For detailed warranty, repair, and
return information, refer to the ADTRAN Equipment Warranty and Repair and Return Policy Proce-
dure (see the last page of this manual).
A return material authorization (RMA) is required prior to returning equipment to ADTRAN.
For service, RMA requests, or more information, see the last page of this manual for the toll-free contact
number.

vi

61200310L1-1 Octal and Quad FXO Modules User Manual vii
Table of Contents
List of Figures ..................................................................................................................................................... ix
List of Tables....................................................................................................................................................... xi
Chapter 1 Introduction.............................................................................................................................. 1-1
Octal and Quad FXO Modules Overview.....................................................................................................1-1
Functional Description.............................................................................................................................. 1-1
Features ....................................................................................................................................................... 1-1
Physical Description.................................................................................................................................. 1-2
Chapter 2 Installation................................................................................................................................ 2-1
Before Installing the Octal and Quad FXO Modules................................................................................... 2-1
Shipping Contents ..................................................................................................................................... 2-1
Installing the Octal and Quad FXO Modules ...............................................................................................2-1
Wiring................................................................................................................................................................. 2-2
Power Up and Initialization............................................................................................................................2-2
Failed Self-Test...........................................................................................................................................2-3
Operation Alarms ...................................................................................................................................... 2-3
Chapter 3 Operation .................................................................................................................................. 3-1
Overview............................................................................................................................................................ 3-1
Terminal Menu Structure................................................................................................................................. 3-2
Modules Menu .................................................................................................................................................. 3-2
Slt .................................................................................................................................................................3-3
Type ............................................................................................................................................................3-3
Menu ........................................................................................................................................................... 3-4
Alarm .......................................................................................................................................................... 3-4
Test .............................................................................................................................................................. 3-4
State ............................................................................................................................................................. 3-4
Status .......................................................................................................................................................... 3-4
Online .................................................................................................................................................. 3-4
No Response ....................................................................................................................................... 3-4
Empty .................................................................................................................................................. 3-4
Offline .................................................................................................................................................. 3-4
Offline/No Response ........................................................................................................................ 3-4
Rev .............................................................................................................................................................. 3-5
Octal and Quad FXO Modules Menu Options............................................................................................. 3-5
Info ...................................................................................................................................................................... 3-5
Part Number .............................................................................................................................................. 3-5
Serial Number ...........................................................................................................................................3-5
Assembly Revision ................................................................................................................................... 3-5
Firmware Revision .................................................................................................................................... 3-5

Table of Contents
viii Octal and Quad FXO Modules User Manual 61200310L1-1
Status...................................................................................................................................................................3-5
Port ..............................................................................................................................................................3-5
Status ...........................................................................................................................................................3-5
Inactive ................................................................................................................................................3-5
Disabled ...............................................................................................................................................3-5
Idle .......................................................................................................................................................3-5
Tip Open .............................................................................................................................................3-6
OffHook ...............................................................................................................................................3-6
Reverse Battery ...................................................................................................................................3-6
Test .......................................................................................................................................................3-6
Test – LO .............................................................................................................................................3-6
Test – LC T/R OK ..............................................................................................................................3-6
Test – LC – No Battery ......................................................................................................................3-6
Test – LC – T/R Rolled ......................................................................................................................3-6
Test – Ring GND ................................................................................................................................3-6
Rx ABCD ....................................................................................................................................................3-6
Tx ABCD ....................................................................................................................................................3-6
Test ......................................................................................................................................................................3-7
Test 2W .......................................................................................................................................................3-7
Tx ABCD ....................................................................................................................................................3-7
1kHz Tone ..................................................................................................................................................3-7
Loopback ....................................................................................................................................................3-7
Configuration.....................................................................................................................................................3-8
Port ..............................................................................................................................................................3-8
Port Name ..................................................................................................................................................3-8
Rx Gain .......................................................................................................................................................3-8
Tx Gain .......................................................................................................................................................3-8
ATLAS 550 Features Used with Octal and Quad FXO Modules ...............................................................3-8
Factory Restore ..........................................................................................................................................3-8
Run Selftest ................................................................................................................................................3-8
Appendix A Dial Plan Interface Configuration......................................................................................A-1
Index...........................................................................................................................................................Index-1

61200310L1-1 Octal and Quad FXO Modules User Manual ix
List of Figures
Figure 1-1. Octal FXO Module....................................................................................................................... 1-2
Figure 2-1. Installing the Octal and Quad FXO Modules.......................................................................... 2-1
Figure 3-1. Modules Menu............................................................................................................................. 3-2
Figure 3-2. Menu Tree for Octal and Quad FXO Modules Menu ............................................................ 3-3
Figure 3-3. Octal and Quad FXO Modules Menu Options ....................................................................... 3-5
Figure A-1. Dial Plan Menus .........................................................................................................................A-1

List of Figures
x Octal and Quad FXO Modules User Manual 61200310L1-1

61200310L1-1 Octal and Quad FXO Modules User Manual xi
List of Tables
Table 2-1. Pinout Connection....................................................................................................................... 2-2
Table 3-1. Test 2W Information................................................................................................................... 3-7

List of Tables
xii Octal and Quad FXO Modules User Manual 61200310L1-1

61200310L1-1 Octal and Quad FXO Modules User Manual 1-1
Chapter 1 Introduction
OCTAL AND QUAD FXO MODULES OVERVIEW
The Octal and Quad FXO Modules are for use in the ATLAS 550 family of
products in applications that require analog phone interfaces. Potential
applications include termination of analog PSTN trunks and connections to
PBX station-side interfaces (OPX). The Octal and Quad FXO Modules
support loop-start and ground-start operation.
Functional Description
The Octal and Quad FXO Modules install in any available option slot in the
ATLAS 550 chassis. Status information is available via the terminal menus,
accessible through either a VT-100 terminal connected to the ATLAS 550
control port or via a Telnet session established through the Base Unit’s
Ethernet port. Use the terminal menu to configure the Octal and Quad FXO
Modules and to download application software.
Features
Features of the Octal and Quad FXO Modules are listed here:
• Eight/four voice ports
• Loop start and ground start
•µ-law
• Hot-swappable
• Part 68 compliant
• Flash downloadable firmware

Chapter 1. Introduction
1-2 Octal and Quad FXO Modules User Manual 61200310L1-1
Physical Description
The Octal and Quad FXO Modules plug into any available option slot in the
rear of the ATLAS 550 chassis. Figure 1-1 shows the Octal FXO Module.
Figure 1-1. Octal FXO Module
The labels over the modular connectors refer to the corresponding ports on
the Octal and Quad FXO Modules.
1
OCTAL FXO
2345678
500 Series

61200310L1-1 Octal and Quad FXO Modules User Manual 2-1
Chapter 2 Installation
BEFORE INSTALLING THE OCTAL AND QUAD FXO MODULES
Carefully unpack and inspect the modules for shipping damages. If you sus-
pect damage occurred during shipping, file a claim immediately with the
carrier and then contact ADTRAN Technical Support (see the last page of
this manual for pertinent information). If possible, keep the original ship-
ping container for returning the modules for repair or for verification of
shipping damage.
Shipping Contents
The ADTRAN shipment includes the following items:
• Octal FXO Module or Quad FXO Module
•Octal and Quad FXO Modules User Manual
(Insert into the ATLAS 550 User Manual.)
INSTALLING THE OCTAL AND QUAD FXO MODULES
Figure 2-1 represents the actions required to install the module properly, as
described in the Step/Action table below.
Figure 2-1. Installing the Octal and Quad FXO Modules
All references to the Octal FXO Module in this chapter are
applicable to the Quad FXO Module, with the difference being that
the Quad FXO Module has four ports instead of eight.
NETWORK 2
24
ETHERNET
CONTROL
IN OUT
RELAY ALARM
OI
FUSE RATING:2A/250V SLO-BLO
90-240VAC, 2A, 50/60Hz
NC NO
COM GND
ALL EMPTY SLOTS MUST BE
COVERED WITH BLANK PANELS
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY
WITH SAME TYPE AND RATINGOF FUSE.
MON
Remove Cover Plate
IO
1
OCTAL FXO
2345678

Chapter 2. Installation
2-2 Octal and Quad FXO Modules User Manual 61200310L1-1
WIRING
Each module port has a single 8-pin modular jack. Connector pinout is com-
patible with (USOC) RJ-11C and is shown in Table 2-1.
POWER UP AND INITIALIZATION
The Octal and Quad FXO Modules require no initialization input during the
power-up sequence, as described in the ATLAS 550 User Manual. Any previ-
ously configured setting for the Octal and Quad FXO Modules is automati-
cally restored upon power-up.
Instructions for Installing the Octal and Quad FXO Modules
Step Action
1Remove the cover plate from the appropriate option slot in the
ATLAS 550 rear panel.
2Slide the module into the option slot until the module is firmly
positioned against the front of the chassis.
3Secure the thumbscrews at both edges of the module. Tighten
with a screwdriver.
4Connect the cables to the associated device(s).
5Complete installation of remaining modules and Base Unit as
specified in the Installation chapter of the
ATLAS 550 User
Manual
.
Option modules are intended to be serviced by qualified service
personnel only.
Table 2-1. Pinout Connection
PIN NAME DESCRIPTION
1, 2, 3, 6, 7, 8 Unused —
4 Ring Ring to and from the analog phone interface
5 Tip Tip to and from the analog phone interface

Chapter 2. Installation
61200310L1-1 Octal and Quad FXO Modules User Manual 2-3
Failed Self-Test
If the module fails self-test, a message displays on the terminal menu self-
test log. See the ATLAS 550 User Manual for details.
Operation Alarms
The red ALARM LED (located with the Module LEDs on the front panel) il-
luminates when an alarm condition is detected.

Chapter 2. Installation
2-4 Octal and Quad FXO Modules User Manual 61200310L1-1

61200310L1-1 Octal and Quad FXO Modules User Manual 3-1
Chapter 3 Operation
OVERVIEW
The Octal and Quad FXO Modules are controlled by the ATLAS 550 Base
Unit terminal menu. The terminal menu allows for detailed configuration,
status, and testing of the Octal and Quad FXO Modules.
Configuration of the Octal and Quad FXO Modules is completed in two ar-
eas:
1. General configuration menus are located in the Octal and Quad FXO
Modules CONFIGURATION menu (MODULES/FX0-8/CONFIG).
2. Specific configuration items depending on how the option module is
used, will show up in the DIAL PLAN (see Appendix A).
Access the terminal menu using either a VT-100 terminal attached to the
ATLAS 550 Base Unit’s control port or a Telnet session established through
the Base Unit’s Ethernet port. The ATLAS550 User Manual provides detailed
instructions on each of these management approaches.
All references to the Octal FXO Module in this section are
applicable to the Quad FXO Module, with the differences that the
Quad FXO Module has four ports instead of eight and is displayed
as FXO-4 in the menus.
To edit items in the terminal menu, you must have the appropriate
password level. Each menu description in this section indicates
the password level required for write and read access. See “Access
Passwords” in the ATLAS 550 User Manual for detailed
information on working with passwords. Security level 0 users
can view and edit every available field. Security level 5 users can
view any field but cannot edit.

Chapter 3. Operation
3-2 Octal and Quad FXO Modules User Manual 61200310L1-1
TERMINAL MENU STRUCTURE
The ATLAS 550 uses a hierarchical menu structure to provide access to all of
its features. The top-most menu level leads to submenus which are grouped
by functionality. All menu items display in the terminal window. To access
the Octal and Quad FXO Modules, activate the MODULES menu. The Octal
and Quad FXO Modules display as FXO-8 under TYPE.
.
MODULES MENU The ATLAS 550 system controller automatically detects the presence of the
Octal and Quad FXO Modules when they are installed in the system. To see
the menus for the Octal and Quad FXO Modules via the terminal menu, use
the arrow keys to scroll to the MODULES menu and press Enter to access the
module choices. Figure 3-1 shows the MODULES menu (see also the menu
tree in Figure 3-2 on page 3-3). The following sections describe all the MOD-
ULES menu options.
Figure 3-1. Modules Menu
Refer to the ATLAS 550 User Manual for detailed instructions
on navigating through the terminal menu.