ADTRAN TSU ACE User manual

Quick Start Guide, 61202295L1-13B, August 2006 Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com.
Quick Start Guide
®
TSU ACE (AC SYSTEM) 1202295L1
DTE
V.35 Cable
NETWORK
T1
4-wire Telco Cable
(Provided)
Network
NETWORK
V.35 Nx56/64 115VAC 60 HZ 0.15A
SPECIFICATIONS
T1/FT1 Interface Supported Standards: AT&T 54016, ANSI T1.403
Line Rate: 1.544 Mbps
Line Code: AMI or B8ZS
Framing: SF or ESF
Input Signal: 0 to -36 dB (DS1)
DS0 Assignment: Contiguous or Alternating
Connector: RJ-48C, V.35
Clock Source Network, Internal, DTE
Diagnostics Test Pattern Generation and Detection: 511, all ones, all zeros, 1:8
Network loopbacks (local and remote); responds to both inband and
FDL loop codes
Compliance FCC Part 15 Class A, ACTA/FCC Part 68, IC CS-03
UL/CUL 60950
Physical Dimensions: 2.75-inch W x 4.25-inch D
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
GETTING STARTED
Two configuration methods are available for your TSU ACE unit:
• Front panel LCD
• ADTRAN’s PC control program, T_Watch PRO
Choose the option which best suits your needs. A limited menu tree is provided on the back of this
sheet for configuring through the front panel LCD.
INSTALLATION INSTRUCTIONS
1. Connect the device to the network T1 circuit through the RJ-48C jack (labeled NETWORK) on
the rear of the unit.
2. Connect the device to DTE equipment through the rear panel V.35 interface (labeled V.35
NX56/64).
3. Connect the power cord to the unit via the receptacle (labeled 115VAC 60HZ 0.15A) and then
to a reliably grounded 115 VAC, 60 Hz power source.
4. Upon the first application of power, the unit will automatically execute self-tests followed by an
initialization sequence. When shipped from the factory, the TSU ACE is uninitialized and set to
factory default conditions.
5. Configure the TSU ACE using the local front panel of the unit or from T-Watch PRO.
Additional information can be found on the TSU Single Port Family
product CD which shipped with the unit. It contains the TSU ACE User
Manual as well as other applicable documentation.

Quick Start Guide, 61202295L1-13B, August 2006 Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com.
Quick Start Guide
®
TSU ACE (AC SYSTEM) 1202295L1
MENU TREE - OVERVIEW
1) STATUS 1) NI PERF REPORTS
2) CURR ERR/ALM
3) ERR/ALM HISTORY
2) CONFIG 1) NETWORK (NI)
MAIN MENU 2) PORT
3) UTIL 1) SOFTWARE REV
2) REINIT UNIT
3) ADDRESS
4) SET PASSCODE
5) KEYPAD
6) FACTORY RESTORE
4) TEST 1) NETWORK TESTS
2) RUN SELF-TEST
3) PORT TESTS
NETWORK (RJ-48C) CONNECTION PINOUTS
Pin Name Description
1 R1 Receive data from the network - Ring 1
2 T1 Receive data from the network - Tip 1
3 — Unused
4 R Transmit data toward the network - Ring
5 T Transmit data toward the network - Tip
6-8 — Unused
V.35 CONNECTION PINOUTS
Pin CCITT Description
A 101 Protective ground (PG)
B 102 Signal ground (SG)
C 105 Request to send (RTS) from DTE
D 106 Clear to send (CTS) to DTE
E 107 Data set ready (DSR) to DTE
F 109 Received line signal detector (DCD) to DTE
H — Data terminal ready (DTR) from DTE
J — Ring indicator (RI)
L — Local loopback (LL)
N — Remote loopback (RL)
R 104 Received data (RD-A) to DTE
T 104 Received data (RD-B) to DTE
V 115 RX clock (RC-A) to DTE
X 115 RX clock (RC-B) to DTE
P 103 Transmitted data (TD-A) from DTE
S 103 Transmitted data (TD-B) from DTE
Y 114 TX clock (TC-A)
AA 114 TX clock (TC-B)
U 113 External TX clock (ETC-A) from DTE
W 113 External TX clock (ETC-B) from DTE
NN&K — Test mode (TM) to DTE