ADTRAN SFP+ Combo PON D1 OLT User manual

Q
uick Star
t
DESCRIPTION
The Combo PON Optical Line Terminal (OLT) Small Form-factor
Pluggable (SFP+) combines the 10 Gig XGS-PON OLT and
GPON OLT optical transceiver into a single-mode fiber SFP+. The
SFP+ plugs into an ADTRAN optical interface that is designed to
accept the Combo PON pluggable optics. The SFP+ provides a
single optical interface to a physical interface and provides a
9.953 Gbps XGS-PON and a 2.488 Gbps GPON interface to the
supporting system when installed into an appropriate product.
Both the XGS-PON and GPON optical burst mode receivers
incorporate APD/TIA optics for maximum sensitivity. The 
XGS-PON transmitter incorporates a 1577 nm EML laser
assembly and the GPON transmitter incorporates a 1490 nm DFB
laser assembly. It is FDA 21 CFR 1040.10 and 1040.11, and IEC
60825-1 Class I laser safety compliant and meets the EU RoHS
Directive.
This SFP+ supports the following features:
■ODN Class D1 (N1/B+) Transceiver
■Data rate: 9.953 Gbps and 2.488 Gbps
■XGS-PON Optical Receive Wavelength: 1270 nm
■XGS-PON Optical Transmit Wavelength: 1577 nm
■GPON Optical Receive Wavelength: 1310 nm
■GPON Optical Transmit Wavelength: 1490 nm
■Hot Pluggable
Applications:
■XGS-PON and GPON Access networks
■Fiber to the Premises (FTTP)
■Fiber to the Building (FTTB)
■Fiber to the Curb (FTTC)
Due to compliance certification requirements, use only pluggable
optics supplied by ADTRAN. ADTRAN cannot certify system
integrity with other pluggable optics.
INSTALLATION
Before installing the equipment, inspect the SFP+. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
Changes or modifications not expressly approved by ADTRAN
will void the warranty.
Installation Steps
To install the SFP+ into an appropriate device, complete the
following steps:
g NOTE
Do not remove the protective dust covers from the SFP+ until the
fiber optic cable is ready to be connected.
1. Insert the SFP+ into the SFP+ cage on the equipment or
device.
2. Slide the SFP+ all the way into the SFP+ cage until there is
an audible “click”.
g NOTE
■Orientation of the SFP+ will vary depending on the equipment.
■The latch on the SFP+ is for removal only. When removing the
SFP+, rotate the latch away from the SFP+. It should easily
slide out of the cage.
w NOTICE
Do not remove the protective dust cover until the optical fiber
connection is made. Ensure that you keep the protective dust
cover on whenever the transceiver optical fiber connector is not
inserted.
3. Continue the installation and turn-up of the device or
equipment using the instructions in the Job Aid or Quick
Start provided with the equipment or device or other system-
level documentation available online at www.adtran.com.
ADTRAN Pluggable Optics
SFP+
Combo PON D1 OLT
November 2020
61442543F1-13A
P/N: 1442543F1

261442543F1-13A
Environmental
■Protected Equipment Severe Environment (Outdoor)
♦System Ambient Operational Temperature Range: 
–40°C to +70°C
♦Storage Temperature Range: –40°C to +85°C
♦Relative humidity: 5% to 95%, non-condensing
SAFETY AND REGULATORY
ENGLISH
f WARNING!
Read all warnings, cautions, notes and installation instructions
before installing or servicing this equipment.
CCAUTION!
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10 and 1040.11 and IEC 60825-1. This product is
NRTL Listed and CB Certified to all applicable American and
European safety standards.
f CAUTION!
■Electrostatic Discharge (ESD) can damage electronic devices.
When handling devices, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place in
antistatic packing material when transporting or storing. When
installing or maintaining, always place devices on an approved
antistatic mat that is electrically grounded.
■This product’s outer case is “electrically isolated” from other
circuits, as a result, this product can be used in systems that
are installed either in a DC-I (isolated) or DC-C (common)
configuration. For Systems where other installed modules or
the host system itself have internal connections between
battery return and frame ground, the system can only be
deployed in a DC-C configuration.
■If the host system has a protective earth (PE) terminal, the PE
terminal of the host system must be connected to protective
earth (PE) to ensure that the exposed metal (i.e., front panels,
optical modules) on the product is properly grounded.
SPECIFICATIONS
General
■Module Type: SFP+
■Media Type: Fiber
♦Single-Mode
♦Single-Fiber
■Signal Data Rate:
♦9.953 Gbps (XGS-PON)
♦2.488/1.244 Gbps (GPON TX/RX)
■Not compatible with SFP+ MSA
■Applications: XGS-PON, GPON, FTTP, FTTB, FTTC
■Optical Connector: SC
Optical
■XGS-PON Transmitter
♦Laser Diode Type: EML
♦Transmit Wavelength: 1577 nm
♦Tx Power: +2.0 dBm to +5.0 dBm
♦Spectral Width: 1 nm
♦SMSR: 30.0 dBm
♦Extinction Ratio: 8.2 dB
■GPON Transmitter
♦Laser Diode Type: DFB
♦Transmit Wavelength: 1490 nm
♦Tx Power: +1.5 dBm to +5.0 dBm
♦Spectral Width: 1 nm
♦SMSR: 30.0 dBm
♦Extinction Ratio: 8.2 dB
■XGS-PON Receiver
♦Type: APD
♦Central Wavelength: 1270 nm
♦Receiver Sensitivity: –26.0 dBm
♦Receiver Overload: –5.0 dBm
■GPON Receiver
♦Type: APD
♦Central Wavelength: 1310 nm
♦Receiver Sensitivity: –28.0 dBm
♦Receiver Overload: –7.0 dBm

61442543F1-13A 3
g NOTE
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, or 3.
■This product is NRTL Listed to the applicable UL/CSA
Standards. The product is designed to meet the applicable
requirements of Telcordia GR-63-CORE, GR-1089-CORE,
and GR-3108-CORE. This product has also been evaluated to
applicable international standards.
■This product is intended for deployment in locations such as
telecommunications facilities (e.g., Central Offices), outdoor
electronic equipment cabinets and at locations where the NEC
applies (such as customer premises). This equipment is
intended to be installed and used only by instructed or skilled
persons. This product is to be installed only in restricted
access locations.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-1-1 “Classification of environmental 
conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental 
conditions, Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental 
conditions, Stationary use at weather protected locations,”
Class 3.3
■This product is designed to function without degradation during
exposure to all test severities per class 3.3 of ETSI EN 300
019-1-3.
■This equipment contains no parts that can be serviced by the
user.
■This product meets EU RoHS Directive. Refer to
www.adtran.com/environmental for further information on
RoHS/WEEE.
FRANÇAIS
f AVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C ATTENTION!
Ce produit est un module laser de classe 1 qui est conforme à la
FDA 21 CFR 1040.10 et 1040.11 et IEC 60825-1. Ce produit est
NRTL et Certifié CB à toutes les normes de sécurité applicables
américains et européens. Pour maintenir la conformité avec les
normes ci-dessus, installer des modules laser de classe 1 ne
ADTRAN approuvés dans les produits d'ADTRAN.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Si le système hôte est doté d'une borne de mise à la terre de
protection (PE), la borne PE du système hôte doit être
connectée à la mise à terre de protection (PE), afin d'assurer
que les parties métaliques à découvert (panneaux frontaux,
modules optiques) du produit soient correctement mis à terre.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com/environmental pour de plus
amples renseignements sur RoHS.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2020 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442543F1-13A*
DEUTSCH
f WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser -Modul, das mit der FDA 21
CFR 1040.10 und 1040.11 und IEC 60825-1 entspricht. Dieses
Produkt wurde NRTL gelistet und CB Certified allen geltenden
amerikanischen und europäischen Sicherheitsstandards. Für die
ständige Einhaltung der oben genannten Normen, installieren Sie
nur ADTRAN zugelassene Klasse 1 Lasermodule in ADTRAN
Produkte.
f VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Falls das Host-System über einen Schutzleiteranschluss (PE)
verfügt, muss der PE-Anschluss des Host-Systems mit dem
Schutzleiteranschluss (PE) verbunden werden, um
sicherzustellen, dass das freiliegende Metall (d. h.
Frontblenden, Optikmodule) am Produkt ordnungsgemäß
geerdet ist.
g HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com/environmental für ausführlichere Informationen
zu RoHS/WEEE.
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)