Advantech TREK-550-A00E User manual

User Manual
TREK-550
Computing Box 

Copyright
The documentation and the software  included with this  product  are  copyrighted  2010  by
Advantech Co., Ltd. All rights
 are reserved. Advantech Co.,  Ltd. reserves the  right  to
make improvements
 in the products described  in this  manual at  any time without 
notice. No  part  of this manual may  be  reproduced, copied, translated  or  transmitted  in
any form
 or by  any means without the  prior written permission of Advantech Co.,  Ltd.
Information provided
 in this  manual is intended to be accurate and  reliable. How-  ever,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of
the rights of third parties, which may result from its use.
Acknowledgements
Intel and Atom are trademarks of Intel Corporation.  Microsoft Windows  and
MS-DOS are registered trademarks of Microsoft Corp.
 All other product names or
trademarks are
 properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its  products will be  free
from defects in materials and workmanship for two years from the date of purchase.
This
 warranty does not apply to  any  products  which  have been repaired  or altered by 
persons other than repair  personnel authorized by Advantech, or which  have been 
subject  to misuse,  abuse,  accident or  improper installation. Advantech assumes no 
liability under the terms of this warranty as a consequence of such events.
Because of
 Advantech’s  high quality-control standards and rigorous testing, most of 
our customers never need to use  our repair service. If  an Advantech  product is defective,
it will be repaired or replaced at no charge during the warranty period. For out-

of-warranty  repairs, you will  be billed according  to the cost  of replacement materials, 
service time  and freight.  Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
 Collect all the  information about the problem encountered. (For example, CPU 
speed, Advantech products used, other hardware and software used,  etc.) Note 
anything abnormal and list any onscreen messages you get when the problem 
occurs.
2.
 Call your dealer and describe the  problem. Please  have  your manual, product, 
and any helpful information readily  available.
3.
 If your product is diagnosed as defective, obtain an RMA (return merchandise 
authorization) number from  your dealer. This allows us to  process  your  return 
more quickly.
4.
 Carefully pack  the defective product, a fully-completed Repair and  Replacement 
Order Card  and  a  photocopy proof of  purchase date (such  as  your sales receipt)  in
a shippable container. A product returned
 without  proof of the purchase date  is not
eligible for warranty service.
5.
 Write  the RMA  number  visibly on the outside of the  package  and ship it prepaid  to
your dealer.
Part No. 2010055001
 Edition 1
Printed in
 Ta i w a n  May 2010
TREK-550 User Manual  ii

Declaration of Conformity
This product  has  passed the CE test for  environmental specifications. Test conditions 
for passing included  the  equipment being  operated within an industrial enclosure.  In 
order to protect the product from being damaged by ESD  (Electrostatic Discharge) 
and EMI leakage,  we strongly  recommend  the use of CE-compliant industrial
enclosure products.
FCC Class B
Note: This  equipment has been tested and found to comply with the limits for a Class  B 
digital device, pursuant to part 15 of  the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses
 and can radiate radio frequency energy and, if  not
installed
 and used  in  accordance with the instructions, may  cause harmful interference
to radio
 communications. However, there is no guarantee that interference  will not
occur in a
 particular  installation. If  this equipment  does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or  more of the 
following measures:
!
 Reorient or relocate the receiving antenna.
!
 Increase the separation between the  equipment and receiver.
!
 Connect  the  equipment into an  outlet on a  circuit different from that to which the 
receiver is connected.
!
 Consult the dealer or an experienced  radio/TV technician for help.
FM
This equipment has passed the  FM certification. According to  the National Fire
Protection Association, work sites are classified into
 different classes, divisions  and 
groups, based  on hazard considerations.  This  equipment is compliant with the 
specifications of Class I, Division 2, Groups A, B, C and  D indoor hazards.
Technical Support and Assistance
1.  Visit the Advantech web site at www.advantech.com/support  for the latest 
information about the product.
2.
 Contact the distributor,  sales representative, or Advantech's customer service 
center for  technical support  if you need  additional assistance. Please have the 
following information ready before you call:
–
 Product name and serial number
–
 Description of your  peripheral  attachments
–
 Description of your software (operating  system, version, application software, 
etc.)
–
 A complete description of the problem
–
 The exact wording of any error messages
iii  TREK-550 User Manual

Warnings, Cautions and Notes
Warning!  Warnings indicate conditions, which  if  not  observed, can cause personal
Injury!
Caution!  Cautions are included to help you avoid damaging hardware or losing 
data. e.g.
There is
 a danger of a  new battery exploding if it  is incorrectly installed.  Do 
not  attempt to recharge, force open,  or heat the battery. Replace  the  battery
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries
 according to the manufacturer's  instructions.
Note!  Notes provide optional additional  information.
Document Feedback
To  assist us in making  improvements  to this  manual,  we would welcome comments 
and constructive criticism. Send all  such in writing to: [email protected]
Packing List
Before setting up, check that the items  listed  below are included, in  good condition. If 
any item does not accord  with the table, please contact your dealer  immediately.
!
 TREK-550 series Computing Box
!
 Accessories for TREK-550
!
 Warranty card
!
 Power cord: DC power inlet cable  (180 cm - for TREK-550 only)
!
 Videio in/CAN cable
!
“ Drivers, Utilities and User Manual" CD-ROM
!
 End User License Agreement (XPE and WinCE model)
Ordering information












Safety Instructions
1.  Read these safety instructions carefully.
2.
 Keep this User Manual for later reference.
3.
 Disconnect this  equipment from  any AC outlet before cleaning. Use a damp 
cloth. Do not use liquid or spray detergents for cleaning.
4.
 For plug-in equipment, the power outlet socket must be located near  the
equipment and must be easily accessible.
5.
 Keep this equipment away  from humidity.
6.
 Put this equipment on a reliable surface during installation.  Dropping it or letting  it
fall may
 cause  damage.
7.
 The  openings  on the enclosure are for air convection. Protect the equipment 
from overheating. DO NOT COVER THE OPENINGS.
8.
 Make sure the voltage of  the power  source is correct  before  connecting the 
equipment to the power  outlet.
9.
 Position the power cord so that people  cannot step on it. Do not place anything 
over the power cord.
10.
 All cautions and warnings on the equipment should be noted.
11 .
 If the equipment is not used for a long time, disconnect it from the power source  to
avoid damage by transient overvoltage.
12.
 Never pour any liquid into an opening. This  may cause fire or electrical shock.
13.
 Never open  the equipment. For safety reasons, the equipment should  be 
opened only by qualified service  personnel.
14.
 If one of the following situations arises, get the equipment checked  by service 
personnel:
15.
 The  power cord or plug is damaged.
16.
 Liquid  has penetrated into the  equipment.
17.
 The  equipment has been exposed to moisture.
18.
 The equipment does not work well,  or you cannot get it to work according to the 
user's manual.
19.
 The  equipment has been dropped and damaged.
20.
 The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT INAN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -30° C (-22° F) OR ABOVE 70° C
(158° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD
BE IN A CONTROLLED ENVIRONMENT.
Operating temperature: 50° C
22.
 CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY 
REPLACED. REPLACE ONLY  WITH THE SAME OR EQUIVALENT TYPE 
RECOMMENDED BY THE MANUFACTURER, DISCARD USED  BATTERIES 
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
23.
 The  sound pressure level  at the  operator's position according to IEC 704-1:1982
is no more than 70
 dB (A).
DISCLAIMER:
 This set of instructions  is given according to IEC 704-1. Advantech 
disclaims all responsibility for the accuracy of any  statements contained herein.
v  TREK-550 User Manual

Wichtige Sicherheishinweise
1.  Bitte lesen sie Sich diese Hinweise  sorgfältig durch.
2.
 Heben Sie diese Anleitung für den späteren Gebrauch  auf.
3.
 Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie 
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch 
zur Reinigung.
4.
 Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht 
zugänglich sein.
5.
 Das Gerät ist vor Feuchtigkeit zu  schützen.
6.
 Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen 
oder Fallen könnte Verletzungen hervorrufen.
7.
 Die Belüftungsöffnungen dienen  zur Luftzirkulation die das Gerät vor überhit- 
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8.
 Beachten Sie beim. AnschluB an  das Stromnetz die AnschluBwerte.
9.
 Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es 
sollte auch nichts auf der Leitung abgestellt werden.
10.
 Alle Hinweise und Warnungen die  sich am Geräten befinden sind zu beachten.
11 .
 Wird das Gerät über einen längeren Zeitraum  nicht benutzt, sollten Sie es vom 
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung 
vermieden.
12.
 Durch die  Lüftungsöffnungen dürfen niemals  Gegenstände oder Flüssigkeiten  in 
das Gerät  gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus- 
lösen.
13.
 Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14.
 Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu  trennen 
und von einer qualifizierten Servicestelle zu überprüfen:
15.
 Netzkabel oder Netzstecker sind beschädigt.
16.
 Flüssigkeit ist in das Gerät eingedrungen.
17.
 Das Gerät war Feuchtigkeit ausgesetzt.
18.
 Wenn das  Gerät nicht der  Bedienungsanleitung  entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine
 Verbesserung erzielen.
19.
 Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
20.
 Wenn das  Gerät deutliche Anzeichen eines  Defektes aufweist.
21.
 VOSICHT: Explisionsgefahr bei  unsachgemaben  Austausch der Batterie.Ersatz 
nur durch densellben order einem vom  Hersteller empfohlene-mahnlichen Typ. 
Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
22.
 ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fach- 
männische  Weise gewechselt wird.  Verfangen Sie die Batterie  nur gleicher  oder 
entsprechender Type, wie  vom Hersteller empfohlen. Entsorgen Sie Batterien 
nach Anweisung des Herstellers.
23.
 Der arbeitsplatzbezogene Schalldruckpegel nach DIN  45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss:
 Die  Bedienungsanleitungen  wurden  entsprechend  der 
IEC-
704-1
 erstellt.  Advantech  lehnt  jegliche  Verantwortung  für  die  Richtigkeit 
der  in  diesem Zusammenhang getätigten Aussagen ab.
TREK-550 User Manual  vi

Safety Precaution - Static Electricity
Follow these simple precautions to protect  yourself  from harm and the products from 
damage.
!
 To avoid electrical shock, always disconnect the power from  your PC chassis 
before you work on it. Don't touch any  components on the CPU card or other 
cards while the PC is on.
!
 Disconnect power before making any configuration changes. The sudden rush  of
power as you connect a jumper or install
 a card may damage sensitive electronic
components.
Warning!  1.  Input voltage rated: 9-36 Vdc.
2.
 Transport: carry  the unit with  both hands and handle with care.
3.
 Maintenance:  to  properly maintain and clean  the  surfaces, use only 
approved products or  clean with  a dry applicator.
4.
 CompactFlash:  Turn off the power before inserting or removing
CompactFlash storage cards.
ropean Contact information: 
Advantech Europe GmbH 
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: [phone]
Fax: [phone]

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation. “Complies with CANADA RSS-210
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment
into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help.
b. FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation
Notes and Warnings to the User and Installer: Caution:
This Installation Guide is intended for use by the professional wireless LAN system installer.
The device cannot be sold retail, to the general public or by mail order. It must be sold to dealers or have strict marketing control.
Who Should Use this Guide:
Installation of this device should be accomplished only by a qualified wireless LAN system installer who is: -Knowledgeable of the
use, installation and configuration procedures and associated networking components.
-Knowledgeable of each system component’s equipment User and Installation Guide.
-Knowledgeable of the installation and configuration procedures for the site’s network infrastructure system and wiring.
-Knowledgeable of the installation procedures, safety, and code requirements for the site’s antenna, antenna mast,
antenna cabling, and installation.
We highly recommend that the antenna installation be performed by a qualified antenna installation professional.
Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority,
or electrician, as appropriate.
Only the approved antenna types may be used with this transmitter
FCC RF Radiation Exposure Statement:
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.


Contents
Contentsix


Chapter1General Information............................1
1.1  Introduction  ...............................................................................................  2
1.2
 General Specifications  ..............................................................................  2
1.2.1  General  .........................................................................................  2
1.2.2
 Standard PC  Functions  .................................................................  3
1.2.3  PCI  Bus Ethernet Interface  ...........................................................  3
1.2.4
 Touchscreen  .................................................................................  3
1.2.5  Environment  ..................................................................................  4
1.3
 LCD Specifications  ....................................................................................  4
Table 1.1:  LCD Specifications  .....................................................  4
1.4
 Dimensions  ...............................................................................................  4
Figure 1.1  TREK-550 dimensions................................................  4
Chapter2System Setup.......................................5
2.1  A Quick Tour of the Mounted  .......................................................  6
Figure 2.1
 Front view  of the  TREK-550  .......................................  6
Figure 2.2
 Left side of the TREK-550  ..........................................  6
Figure 2.3  Rear view of the TREK-550  ........................................  7
Figure 2.4
 Computing Box  I/O  ...................................  7
2.2  Installation Procedures..............................................................................  8
2.2.1
 Connecting  the Power Cord  ..........................................................  8
Table  2.1:  Pin Definition  of Power Cord  ......................................  8
2.2.2
 Connecting the  Keyboard or  Mouse  .............................................  8
2.2.3  Switching  on the Power  ................................................................  8
2.3
 Running the BIOS  Setup Program  ............................................................  9
2.4  Installing System Software  ........................................................................  9
2.5
 Installing the Drivers................................................................................  10
2.6  Programming Function  Keys  and GPIO/CAN BUS  .................................  10
ix
 TREK-550 User Manual

Chapter4Jumper Settings and Connectors...19
4.1  Setting Jumpers and Switches................................................................  20
4.1.1
 Locating Jumpers and Switches  .................................................  20
Table 4.1:  Jumpers  & LEDS on the  Motherboard  .....................  20
4.1.2
 Locating Jumpers and LEDs on the Motherboard  ......................  21
Figure 4.1
 Locating Jumpers /  LEDs  .........................................  21
4.1.3  Connectors  on the Motherboard  .................................................  22
Table 4.2:  Connectors  on the Motherboard...............................  22
4.1.4
 Locating Connectors on  the  Motherboard  ..................................  23
Figure 4.2  Locating Connectors on  the  front side......................  23
Figure 4.3
 Locating Connectors on  the  back  side  .....................  23
4.2  CPU Installation  ......................................................................................  24
4.3
 Jumper Settings  ......................................................................................  24
4.3.1  CMOS Clear for External  RTC (JP1)  ..........................................  24
Table 4.3:  Clear CMOS /  External RTC (JP1)  ...........................  24
4.3.2
 Power Feature  Setting (JP3)  ......................................................  24
Table 4.4:  Ignition Input  Switch  Setting (JP3)  ...........................  24
Table 4.5:
 Power off  / Hard off Delay Setting (JP3)  ..................  25
Table 4.6:  Low Battery Monitor (JP3)  ........................................  26
4.4
 COM Port Interface  .................................................................................  27
Table 4.7:  Serial  Port Default  Settings  ......................................  27
4.4.1
 COM Port Pin 9 Power Output  Setting  (CN27)  ...........................  28
Table 4.8:  COM  Port Pin 9 Power  Output Setting (CN27)  ........  28
4.4.2
 COM Port Pin 9 Power Output  Value Setting  (JP2)....................  28
Table 4.9:  COM  Port Pin 9 Power  Output Value Setting (JP2)  .  28
Chapter5Pin Assignments...............................43
A.1  Internal  Speaker Connector (CN2 on  PCM-028)  ....................................  44
Table
 A.1:  Internal Speaker  Connector (CN2 on PCM-028)  ......  44
A.2  COM1, 2 (CN17,19)  ................................................................................  44
Table
 A.2:  COM1, 2 (CN17,19)..................................................  44
A.3  GPIO  / CAN BUS Connector  (CN31)  ......................................................  45
Table A.3:
 GPIO  / CAN BUS  Connector  (CN31)  .......................  45
A.4  Inverter  / Touch  / USB Connector  (CN18)  ..............................................  46
Table A.4:
 Inverter  / Touch  / USB Connector (CN18)  ................  46
A.5  Power Inlet  ..............................................................................................  47
Table A.5:
 Power inlet  ................................................................  47
Chapter6SW demo application set Up...............43
A.1  J1939/CAN……………………………………………  ....................................  44
Table  A.1:   ............. ................................ ................................  44
A.2
 RTC.......................................................................... ...............................  44
Table  A.2:  ................................................ .................................  44
A.3  Power management  ........................... .....................................................  45
Table A.3:
 GPIO  / CAN BUS  Connector  (CN31)  .......................  45
A.4  GPIO  .......................................... ..........................................................  46
A.5
 Video ................ .......................................................................................  44
Table  A.2:  ......... ........................................................................  44
A.6
 Dead reckoning  ................ .....................................................................  45
Table A.3:  ..............................................................................  45
A.7
 G-sensor  ...............................................................................................  46
AppendixATREK-303.....................................49
B.1  TREK-303 spec  ........................................................................  50
B.1.1
 .............................................................  50
B.2  Other Information  ....................................................................................  65
xi
 TREK-550 User Manual

Chapter 1
1  General Information
This chapter gives background
information on the TREK-550
Computing Box.
Sections include:
!Introduction
!General Specifications
!Dimensions


1.1Introduction
The TREK-550 is a dedicated box computer for industrial, transport trucks, buses and
taxis. TREK-550 combined with variety of I/O connectors can be connected to
devices like OBD-II or TPMS (Tire Pressure Monitoring System). Dual display/dual
audio interfaces supporting different resolutions can deliver different applications to
different displays; eg: one application to a driver and another to a digital signage
application.
Built-in wireless communications (WWAN, WLAN, ) enable TREK-550 to send
important driver/ location/cargo information back to the control center. TREK-550 can
also operate in extreme environments with features like a wide working temperature
range (-30 to 70 degrees). TREK-550 also uses a special design to handle the critical
issue of in power. Special power protection (ISO7637-2/SAE J1455 Class A/ SAE
J1113) and power management software (Ignition on/off, delay on/off, low battery
monitor) prevent electrical noise and surges from impacting the system, guarding
against damage from transient power. TREK-550 also support rear view monitor
through connecting video in port. With this feature, driver can real time monitor the
environment on two sides of the truck for driving safety. TREK-550 can also support
dead-reckoning feature, which means the truck can still be traced even the driver is
driving in a tunnel.
Rear-Side Connectors















1.2General Specifications
Key features
zSupports Win CE 6.0, XPE, XP and Linux
zAutomotive grade working temperature range (-30° C to 70° C)
zRich I/O including CAN, LAN, RS-232, RS-485, J1708, isolation 4DI/4DO, Line out,
Mic in, USB, and Video-in
zBuilt-in communication modules, including GSM/GPRS/HSDPA/CDMA, WLAN
zGPS with AGPS and dead reckoning technology (Gyro & speed line)
zCertifications: CE/FCC/e-mark, MIL-SD810F, ISO 7637-2, SAE J1455, SAE J1113
regulations
zDual display/audio output for both driver and passenger
zIgnition on/off delay; SW detectable/controllable for power management
1.2.1  General
!  Dimensions : (W x H x D): 271 x 149 x 69.7 mm.
!
 Weight : 2 kg.
!
 Power supply :
–
 Input voltage : 6  ~ 36Vdc, support ignition cold crank
–  Ignition on/off
–  Low battery shut-down protection threshold  (optional) : When the battery 
voltage level  drops below 11V for more than 30 seconds, TREK-550  will
automatically shut down in order to prevent “deep discharge” situations
 and
TREK-550 can be re-activated only when the voltage is > 11V.
–
 Power on delay :  Default 2 seconds. When  the TREK-550 is powered on via 
ignition key, the system will  delay 2  seconds to power  on.
–
 Power off delay : Default 5 seconds. When TREK-550 power is controlled by 
ignition key  and turns  off by the key (ignition=off), the TREK-550 will  start  the 
shut procedure after 5  seconds.
–
 Hard off  delay : Default  30  seconds. When TREK-550 power  is controlled  by 
ignition key and turns off by the key (ignition=off), the TREK-550 will cut off  the
5VSB power after 30 seconds. In
 this event when the shutdown process  is
longer than 30 seconds, the power will be shut down hard,
 turning off the 
TREK-550's power  and 5VSB.
Note!  For more detail of function please  refer to  Chapter 4, Section 4.3.2 of 
this manual.
!
 Power consumption : The maximum current consumption is about 32.4 watts. 
The power  consumption is 12 watts in normal mode (with only XPE running;  no 
I/O device and modules connected to  the TREK-550).
!
 Front panel and back cover : IP65 Sealed; NEMA4 compliant
(Not including the I/O ports).
!
 Enclosure : Ruggedized aluminum without ventilation  holes.

1.2.2  Standard PC Functions
!  CPU : Intel Atom Z510PT 1.1Ghz/ Z520PT 1.3Ghz
!
Chipset : Integrated in LE82US15EE
!
 BIOS : Award 256  KB Flash BIOS, ACPI 2.0  Compliant.
!
 System chipset :.
!
 System memory :  One 200-pin SODIMM  sockets, accepts up to  2  GB DDR667
DDR
!
 Solid state disk : Supports one 50-pin socket  for Compact-Flash type I/II (True
PATA mode).
!
 Serial ports : Two RS-232, 5V@500mA,12V@ 250mA, ping9, by jumper selected.
One 4-wire RS232,1 x RS485, 1 x J1708 ports.
!
 Universal serial bus (USB) port : Supports up to three USB2.0. One from smart
display port.
!
 LAN port : 1 x 10/100/1000 Ethernet (with LEDs) by RJ45.
!
 Video output : 1 x VGA output by DB-15 (independent display).
!
 Video in : 2 x composite video input selection supported format (for rear view
monitor) by RJ-45 connector
!
 Mini PCI express bus expansion slot : Accepts half size mini PCI bus card.
!
 Watchdog timer : 63-level timer  intervals automatically  generate system reset 
when the system stops  due to a program error or EMI. Jumper selection  and 
software enabled/disabled.
!
 RTC Battery : 3.0 V @ 195  mA lithium battery.
!
 Power management : Supports power saving  modes including Normal/ 
Standby/Suspend modes.  APM 1.2 compliant.
!
 Digital I/O :  Optically  isolated 4 digital input and 4 digital output
!
 CAN bus : RS-232 baud rate up to 115.2K bps.
!
 Audio controller : AC97 Ver. 2.0  compliant interface, Multi stream
Direct sound and Direct Sound 3D acceleration.
!
 Stereo sound : 18-bit full-duplex codec.
!
 Audio interface : One 2W speaker, one  microphone. One line out.
!
 Optional modules : 12  channels GPS, quad-band  GSM/GPRS, MiniPCI  WLAN
card.
1.2.3  PCI Bus Ethernet Interface
!  Chipset : Realtek RTL8100CL PCI local bus Ethernet controller.
!
 Ethernet interface : Full  compliance with IEEE 802.3u 100Base-T and 10 Base-  T
specifications. Includes
 software drivers and boot ROM that supports both  RPL
and
 PXE.
!
 100/10Base-T auto-sensing capability.
1.2.4  Touchscreen
!  Ty p e : Analog Resistive
!
 Light transmission : 80%
!
 Controller : RS-232  interface
!
 Power consumption : <5.5 V@ 20 mA
!
 Durability : > 10 million depressions
!
 Software driver : Supports Windows XP/XP Embedded, WinCE

1.2.5  Environment
! High/low temperature: -30 ~ 70° C 
!  Relative humidity :  10 ~ 95% @ 40° C (non-condensing)
!
 Shock : 30 G peak acceleration (11 msec duration)
!
 Certifications : CE, FCC, CCC, Emark, CB.
!
 Vibration : 5 ~ 500 Hz SAE J1455 4.9.4.2, MIL-STD-810F 514.5
1.4Dimensions






Figure 1.1  TREK-550 dimensions
TREK-550 User Manual  4


Chapter
2Syst
System Setup
This chapter details system setup
on TREK-550.
Sections include:
!A Quick Tour of the computer box
!Installation Procedures
!Running the BIOS Setup
Program
















2.1A Quick Tour of the TREK-550 Computing box.

Before  starting to set up the Computing Box,  take  a  moment  to become  familiar with the locations
and
 purposes of the controls,  drives, connectors and ports,  which are illustrated  in  the figures
below. When the
 Computer box is  placed inside truck glove cabinet or under the passenger’s seat
next to the driver, its front appears as shown
 in  Figure 2.1.

Figure 2.1. front view of TREK-550 
Figure 2.1.fdasdf
Figure 2.2. Rear view of TREK-550 
Unit: mm
Figure 2.3. Side view of TREK-550 

Unit: mm

Figure 2.4. Bottom view of TREK-550 
Unit: mm

Figure 2.5. Top view of TREK-550 

2.2Installation Procedures
2.2.1  Connecting the Power Cord
Connect the  three pin waterproof power cord to the DC  inlet  of  the Computing Box.
On the
 open-wire end, one pin is reserved for positive voltage and is  marked, 
"+"; one pin is  reserved  for ground  and  is  marked,  "-"; and, one pin is 
reserved for the ignition signal with an “ignition” mark.
Note!  Power on/off the  TREK-550 via the TREK-550's power switch. Please 
connect its  "+ "  and  " ignition"  pins together with the power  source's 
"+".
 Or change the  JP3 jumper setting.  (For JP3 jumper setting  please
see
 section 4.3.2.1)

Note!  Ignition  on/off  setting : The TREK-550 supports an ignition on/off 
func-  tion so that you can power on/off the TREK-550 via the ignition
signal/
 voltage. Either connect the TREK-550's "ignition" pin to ignition  and 
the TREK-550 "+-"  to "+-" ; or connect the TREK-550's "ignition &
+" pins together
 with power  source's  "+" , and  "-" to "-". Please  also
set
 the "power on after power  failure” function to "always on" in
BIOS.(for
 BIOS settings, please see Appendix D). The delay on/off
will be active
 once the  ignition  on/off is selected.
Table 2.1: Pin Definition of Power Cord
Pin  Definition  Color
1  +  yellow
3
 -  black 
4  Ignition  white
Power Connector
 

Molex Manufacturer part no. 0430451200
Power Connector
Pin Signal Pin Signal
1 Chassis Ground 2 Ground
3 Ground 4 (Reserved)
5(Reserved) 6 (Reserved)
7Power Input (6~36 VDC) 8 Power Input (6~36 VDC)
9Acc Ignition Input 10 Ground
11 (Reserved) 12 Power Button Input
Mating power cable
Advantech p/n : 1700018306 A Cable 2*6P-3.0/fuse 180cm TREK
Manufacturer p/n: Best Technology Enterprise 900-1200-180R

















