Advantech PCM-4380 Installation and operation manual

PCM-4380 Startup Manual1
PCM-4380 Pentium ® M 4" SBC with MIO/VGA/
LVDS Ethernet/USB2.0
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note 1: For detailed contents of the PCM-4380, please
refer to the enclosed CD Disc or disk (in PDF for-
mat).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
http://www.adobe.com/products/acrobat/
readstep2.html (Acrobat is a trademark of Adobe.)
Standard SBC Functions
• CPU: Embedded Intel Pentium M (Banias/Dothan) /LV/
ULV Celeron M Processor supported at Front Side Bus
(FSB) 400MHz
on board Pentium M 1.4GHz (2M L2 cache) PCM-
4380F-S4A1E
on board Celeron M 1.0GHz (1M L2 cache) PCM-
4380F-S0A1E
• System Chipset: Intel 855GME GMCH/ICH4 Chipset
• BIOS: Award 512 Kbit Flash BIOS
• System Memory: 200 pin SODIMM socket, support
ECC Double Data Rate (DDR) 128 MB to 1 GB, accept
128/256/512/1 G, DDR 200/266 DRAM
• Power Management: APM1.2, ACPI support
• SDD: Supports CompactFlash Card Type I/II (shared
2nd IDE Channel) USB memory, uDOC (option)
• WatchDog Timer: Single chip watchdog 255-level timer
interval, setup by software
• Expansion Interface: Supports 8/16 bit ISA bus for
standard PC/104 device (ITE 8888g), PC/104-Plus
• Battery: 2 pin wafer box for external Battery on board
Enhance IDE Interface 1 x EIDE (UDMA 33), 1 x FDD, 1
x K/B, UDMA 100 with PCM-063 riser card, 1 x Key-
board/Mouse, 3 x RS232, 1 x RS-232/422/485, 1 x LPT
• USB: 6 x USB 2.0 compliant Ports (2 ports on board
connector, 4 ports pin-head)
• Audio: ICH4 AC97 3D surround stereo sound, supports
Speaker-out, CD-input, Line-in, Line-out, Microphone
(with PCM-4386D option)
Solid State Disk
• Supports one 50-pin socket for CFC type I/II
VGA/LVDS Interface
• Chipset: Intel 855GME chip integrated (Extreme Graph-
ics 2)
• Memory Size: Optimized Shared Memory Architecture,
support up to 64MB frame buffer using system memory
• Resolution:
CRT Display Mode: pixel resolution up to
1600 x 1200 @85 Hz and 2048 x 1536 @75 Hz
LCD Display Mode: Dual channel LVDS panel sup-
ports up to UXGA panel resolution with frequency range
from 25 MHz to 112MHz
with frequency range from 25-MHz to 112-MHz
• LCD Interface: 2 Channel (2 x 18/36-bit) LVDS
• LVDS: Hirose connector support up to 2 channel (2 x 18-
bit) LVDS LCD Panel
• Dual Independent Display: CRT+ 36bit LVDS
Ethernet interface
• Chipset supports:
10/100 Mbps - Intel 82551ER
10/100/1000Mbps - Intel 82541GI (Optional)
• Ethernet interface: 2 x RJ45
Packing List Specifications
• 1 PCM-4380 SBC
• 1 Startup manual
• 1 Utility CD
• Cable 20P/10P 10CM EPIC
ATX Power p/n: 1700002055
• Flat Cable 44P IDC 44P/44P/
40P Keyed 50CM p/n: 1701440504
• USB 2 Connector p/n: 1700100170
• Keyboard/Mouse Connector p/n: 1700060202
• Flat cable 44P 20CM 3COM
& LPT 1.27mm to D-sub p/n: 1700002034
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the PCM-4380 Series Rev. A1.
Part No. 2006438000 1st Edition
Oct. 2006
PCM-4386 Celeron®M 4" SBC with MIO/VGA/LVDS Ethernet/USB2.0

2 PCM-4380 Startup Manual
• Standard: IEEE 802.3u 100Base-T
Audio Function
• Audio controller: Support AC97 3D surround stereo sound
• Audio interface: Speaker-out, CD-input, line-in, Line-out
Microphone (with PCM-4386D option)
Mechanical and Environmental
• Dimensions 115 x 165 mm (4.5"x 6.5")
Mechanical Drawing (dxf file) is available.
• Power Supply Type: ATX
• Power Supply Voltage: +5V ±5%, +12V ±5%
• Power Consumption: (Celeron M 600 with 256 MB
DDR266)
• Operating Humidity: 0%~90% relative humidity, non-con-
densing
• Operating Temperature: 0 ~ 60°C (32 ~ 140°F)
• Weight: 0.85 kg (weight of total package)
The board has a number of jumpers that allow you to con-
figure your system to suit your application.
The table below lists the function of each of the jumpers
and connectors.
Jumpers and Connectors
Jumpers
Label Function
J2 LCD Power
J3 COM2 Setting
J4 PCI VIO Setting
Connectors
Label Function
CN1 ATX Power connector
CN3 DDR-SODIMM (RVS)-5.2mm
CN4 Battery connector
CN5 System Fan
CN6 Power Switch
CN7 GPIO connector
CN8 LAN1 (RJ45 + 1G Transformer)
CN9 LAN2 (RJ45 + 1G Transformer)
CN11 Compact II W/Ejector
CN13 HD & Power LED
CN14 LVDS connector
CN15 Inverter Power
CN16 VGA connector
CN18 USB 0/1
CN19 Keyboard/Mouse
CN21 COM1
CN23 LPT AC97 (BH 15*2 1.27mm)
CN24 ISA -5V
CN26 RS-422/485
CN27 IDE0
CN30 COM 2/3/4 & LPT
CN31 USB 2/3 & AC97 (Audio I/F)
J2: LCD Power
Pin Signal
1-2 +5V
2-3 +3.3V
J3: COM2 Setting
Pin Signal
(1-2) RS232
(3-4) RS485
(5-6) RS422
J4: PCI VIO Setting
Pin Signal
1-2 +5V
2-3 +3.3V
123 123
123 123

PCM-4380 Startup Manual 3
PCM-4380 Connectors (component side)
PCM-4380 Connectors (solder side)

4 PCM-4380 Startup Manual
PCM-4380 Mechanical Drawing (component side)
PCM-4380 Mechanical Drawing (solder side)