Advantech PCA-6190 User manual

PCA-6190
LGA775 Pentium® 4/Cele-
ron® D Processor Card with
VGA/Dual Gigabit LAN/HISA/
DVI (800 MHz FSB)
User’s Manual

PCA-6190 User’s Manual ii
Copyright Notice
This document is copyrighted, 2005, by Advantech Co., Ltd. All rights
are reserved. Advantech Co., Ltd. reserves the right to make improve-
ments to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to
be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
Acknowledgements
•AWARD is a trademark of Phoenix Technologies Ltd.
•IBM and PC are trademarks of International Business Machines Corpo-
ration.
•Intel®, Pentium® 4, and Celeron® are trademarks of Intel Corporation.
•WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are the properties of their respec-
tive owners.
Part No. 2002619000 1st Edition
Printed in Taiwan September 2005

iii
1.0.1 A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifica-
tions to ensure reliable performance in the harsh and
demanding conditions typical of industrial environments. Whether your
new Advantech equipment is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and
ease of operation for which the name Advantech has come to be known.
Your satisfaction is our primary concern. Here is a guide to
Advantech’s customer services. To ensure you get the full benefit of our
services, please follow the instructions below carefully.
Technical support
We want you to get the maximum performance from your products. So if
you run into technical difficulties, we are here to help. For the most fre-
quently asked questions, you can easily find answers in your product doc-
umentation. These answers are normally a lot more detailed than the ones
we can give over the phone.
So please consult this manual first. If you still cannot find the answer,
gather all the information or questions that apply to your problem, and
with the product close at hand, call your dealer. Our dealers are well
trained and ready to give you the support you need to get the most from
your Advantech products. In fact, most problems reported are minor and
are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers
every business day. We are always ready to give advice on application
requirements or specific information on the installation and operation of
any of our products.

PCA-6190 User’s Manual iv
Table 1.1: Table 1.1: PCA-6190 Comparison Table
Model PCA-6190VG-
00A1
PCA-6190G2-
00A1
PCA-6190G2-
D0A1
VGA: Intel 915 GV integrated
VGA controller onboard
yes yes yes
USB 2.0 port 8 8 8
LAN 1: Broadcom BCM5721
10/100/1000Base-T
no yes yes
LAN 2: Broadcom BCM5721
10/100/1000Base-T
yes yes yes
DVI function no no yes
PCI B-to-B daughter board
connector
no no yes
Note: PCA-6190VG-00A1 uses onboard LAN2 controller

v
Table 1.2: PCA-6190 DDR memory compatibility table
Brand Size Speed Type ECC Part
Number
Advan-
tech PN
Memory
Apacer 1 GB DDR2 533 DDR2 N 78.01066.
330
NA HYB18T5
12
800AF37
FSS35249
0434
1 GB DDR2 533 DDR2 N 78.01066.
400
NA SAM-
SUNG
K4T51083
QB-ZKD5
UG 512 MB DDR2 400 DDR2 N UG64T64
00K8DU-
4AM
NA 4WB42
D9CHL
1 GB DDR2 400 DDR2 N UG12T64
00L8DU-
4AM
NA EPPIDA
E5108AB-
5C-E
Transcend 256 MB DDR2 533 DDR2 N NA NA SAM-
SUNG 443
K4T56083
QF-GC05
1 GB DDR2 533 DDR2 N NA NA ELPIDA
E5108AB-
5C-E
DSL 512 MB DDR2 533 DDR2 N NA NA HYB18T5
12
800AF37
FSS43331
0440
1 GB DDR2 400 DDR2 N NA NA HYB18T5
12A
800AF37
FSS43331
0440

PCA-6190 User’s Manual vi
1.0.1 Product warranty
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
If an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
Step 1. Collect all the information about the problem encountered. (For
example, type of PC, CPU speed, Advantech products used,
other hardware and software used, etc.) Note anything abnormal
and list any on-screen messages you get when the problem
occurs.
Step 2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
Step 3. If your product is diagnosed as defective, obtain an RMA (return
material authorization) number from your dealer. This allows us
to process your return more quickly.
Step 4. Carefully pack the defective product, a fully-completed Repair
and Replacement Order Card and a photocopy proof of purchase
date (such as your sales receipt) in a shippable container. A prod-
uct returned without proof of the purchase date is not eligible for
warranty service.
Step 5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

vii
1.0.2 Initial Inspection
Before you begin installing your single board computer, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
We have carefully inspected the PCA-6190 mechanically and electrically
before shipment. It should be free of marks and scratches and in perfect
working order upon receipt.
As you unpack the PCA-6190, check it for signs of shipping damage.
(For example, damaged box, scratches, dents, etc.) If it is damaged or it
fails to meet the specifications, notify our service department or your
local sales representative immediately. Also notify the carrier. Retain the
shipping carton and packing material for inspection by the carrier. After
inspection, we will make arrangements to repair or replace the unit.
1.0.3 Release Note
1 PCA-6190 Pentium 4/Celeron Dprocessor-based single board computer
1 PCA-6190 Startup Manual
1 CD with driver utility and manual (in PDF format)
1 FDD cable P/N: 1700340640
1 Ultra ATA 66/100 HDD cables P/N: 1701400452
4 Serial ATA HDD data cable P/N: 1700071000
4 Serial ATA HDD power cable P/N: 1703150102
1 ATX 12V power converter cable P/N: 170304015K
1 Printer (parallel) port & COM port cable kit P/N: 1700060305
1 Dual COM port cable kit (certain models) P/N: 1701092300
1 Y cable for PS/2 keyboard and PS/2 mouse P/N: 1700060202
2 Four-USB port cables P/N:1700000719
Jumper pack P/N:9689000068
DVI cable (PCA-6190G2-D0A1 only) P/N: 1700000821
Warranty card
Date Revision Description
September 2005 1st Edition Initial Release

PCA-6190 User’s Manual viii
Important Safety Information
SAFETY INSTRUCTIONS
This device complies with the requirements in part 15 of the FCC
rules: Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this device in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his/her own expense. The user is advised that any
equipment changes or modifications not expressly approved by the party responsible for
compliance would void the compliance to FCC regulations and therefore, the user's
authority to operate the equipment.
CAUTION!!
There is a danger of a new battery exploding if it is incorrectly installed. Do not
attempt to recharge, force open, or heat the battery. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Discard used bat-
teries according to the manufacturer’s instructions.

ix
Contents
Chapter 1 Hardware Configuration .................................2
1.1 Introduction ....................................................................... 2
1.2 Features ............................................................................. 3
1.3 Specifications .................................................................... 4
1.3.1 System............................................................................. 4
1.3.2 Memory........................................................................... 4
1.3.3 Input/Output.................................................................... 4
1.3.4 VGA interface................................................................. 5
1.3.5 Ethernet LAN.................................................................. 5
1.3.6 Industrial features ........................................................... 5
1.3.7 Mechanical and environmental specifications................ 5
1.4 Jumpers and Connectors.................................................... 6
Table 1.1:Jumpers........................................................... 6
Table 1.2:Connectors ...................................................... 6
1.5 Board Layout: Jumper and Connector Locations.............. 9
Figure 1.1:Jumper and Connector locations ................... 9
1.6 PCA-6190 Block Diagram ............................................. 10
Figure 1.2: ................................................................... 10
1.7 Safety Precautions .......................................................... 11
1.8 Jumper Settings ............................................................... 12
1.8.1 How to set jumpers ....................................................... 12
1.8.2 CMOS clear (J1) ........................................................... 12
Table 1.3:CMOS (J1).................................................... 12
1.8.3 Watchdog timer output (J2) .......................................... 13
Table 1.4:Watchdog timer output (J2).......................... 13
1.9 System Memory .............................................................. 13
1.9.1 CPU FSB and memory speed ....................................... 14
1.9.2 Dual channel configuration........................................... 14
1.10 Memory Installation Procedures ..................................... 14
1.11 Processor Installation ...................................................... 15
Chapter 2 Connecting Peripherals .................................18
2.1 Introduction ..................................................................... 18
2.2 1st (CN1) IDE Connectors .............................................. 18
2.3 Floppy Drive Connector (CN3)....................................... 19
2.4 Parallel Port (CN4).......................................................... 19
2.5 USB Ports (CN6,CN63,CN66,CN67)............................. 20
2.6 VGA Connector CN7 ...................................................... 20
2.7 DVI Connector VCN1 (optional).................................... 21

PCA-6190 User’s Manual x
2.8 Ethernet Connector (CN24) ............................................ 21
2.9 Serial Ports (COM1: CN9/CN91; COM2: CN10 ) ......... 22
2.10 PS/2 Keyboard/Mouse Connector (CN11)...................... 22
2.11 External Keyboard Connector (CN12)............................ 23
2.12 CPU Fan Connector (CN68) ........................................... 23
2.13 Front Panel Connectors (CN16, 17, 18, 19, 21&29)....... 24
2.13.1 Power LED (CN16) ...................................................... 24
2.13.2 External speaker (CN17) .............................................. 24
2.13.3 Reset (CN18) ................................................................ 25
2.13.4 HDD LED (CN19)........................................................ 25
2.13.5 ATX soft power switch (CN21).................................... 25
2.13.6 SM Bus Connector (CN29)........................................... 25
2.14 ATX Feature Connector (CN20)..................................... 26
2.15 AC-97 Audio Interface (CN43)....................................... 26
2.16 Serial ATA Interface (SA0,SA1,SA2, and SA3) ............ 26
2.17 Connecting to SNMP-1000 Remote Manager ................ 27
2.18 Auxiliary 4-pin Power Connector (ATX1) ..................... 27
2.19 SCSI Daughterboard Extension Connector (CN30)........ 28
2.20 Case Open Connector (CN64)......................................... 28
2.21 Front Panel LAN Indicator Connector (CN65)............... 29
2.22 GPIO Pin Header (CN93) ............................................... 29
Chapter 3 Award BIOS Setup.........................................32
3.1 Introduction ..................................................................... 32
3.1.1 CMOS RAM Auto-backup and Restore ....................... 32
3.2 Entering Setup ................................................................. 33
Figure 3.1:Award BIOS Setup initial screen ................ 33
3.3 Standard CMOS Setup .................................................... 33
3.3.1 Date............................................................................... 33
3.3.2 Time.............................................................................. 33
3.3.3 IDE channel 0/1 Master/Slave ...................................... 33
3.3.4 Drive A / Drive B.......................................................... 34
3.3.5 Halt On.......................................................................... 34
3.3.6 Memory......................................................................... 34
Figure 3.2:Standard CMOS Features Screen................ 34
3.4 Advanced BIOS Features ................................................ 35
Figure 3.3:Advanced BIOS features screen.................. 35
3.4.1 CPU Features ................................................................ 35
3.4.2 Hard Disk Boot Priority................................................ 35
3.4.3 Virus Warning............................................................... 36
3.4.4 CPU L1 & L2 Cache..................................................... 36
3.4.5 Hyper-Threading Technology....................................... 36
3.4.6 Quick Power On Self Test ............................................ 36
3.4.7 First/Second/Third Boot Device ................................... 36