Advantech PCE-2033 User manual

User Manual
PCE-2033/2133
LGA1700 12th/13th Generation
Intel® Core™ i9/i7/i5/i3 &
Pentium®/Celeron® CPU Board
for IPC-2 Series Chassis

PCE-2033/2133 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2023
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
AMIBIOS is a trademark of American Megatrends Inc.
Intel®, Core™ i9/i7/i5/i3, Pentium®, Celeron and Xeon are trademarks of Intel® Cor-
poration.
Nuvoton is a trademark of Nuvoton Technology Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product is defective, follow the steps outlined below:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2001213300 Edition 1
Printed in China December 2023

iii PCE-2033/2133 User Manual
Declaration of Conformity
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference. In
this event, users are required to correct the interference at their own expense.
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
Specification Comparison
Model Chipset Intel CPU
Support USB 3.2 USB 2.0 GbE NVMe M.2 miniPCI COM
PCE-2133 Q670E 12th/13th Gen 8 0 2 1 (PCIe x4 M Key) 1 (Full-Size) 2
PCE-2033 H610E 12th/13th Gen 4 4 2 0 1 (mSATA Only) 2

PCE-2033/2133 User Manual iv
Initial Inspection
Before you begin installing your motherboard, please make sure that the following
materials have been shipped:
1 x PCE-2033 or PCE-2133 CPU Board
1 x I/O Shield
1 x Startup manual
1 x Warranty Card
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the PCE-2033/2133 mechani-
cally and electrically before shipment. It should be free of marks and scratches and in
perfect working order upon receipt. As you unpack the PCE-2033/2133, check it for
signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is
damaged or it fails to meet the specifications, notify our service department or your
local sales representative immediately. Also notify the carrier. Retain the shipping
carton and packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.

i PCE-2033/2133 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ............................................................................................... 2
1.2 Features & Benefits................................................................................... 2
1.3 Specifications............................................................................................ 2
1.3.1 System .......................................................................................... 2
1.3.2 Memory ......................................................................................... 2
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 3
1.3.6 Industrial Features ........................................................................ 3
1.3.7 Mechanical and Environmental Specifications.............................. 3
1.4 Jumpers and Connectors .......................................................................... 4
Table 1.1: Jumper List ................................................................. 4
Table 1.2: Connectors ................................................................. 4
1.5 Board Layout: Jumper and Connector Locations...................................... 5
Figure 1.1 Jumper and Connector Locations............................... 5
Figure 1.2 Jumper and Connector Locations............................... 5
1.6 Block Diagram........................................................................................... 6
Figure 1.3 PCE-2033/2133 Block Diagram.................................. 6
1.7 Safety Precautions.................................................................................... 6
1.8 Jumper Settings ........................................................................................ 7
1.8.1 How to Set Jumpers...................................................................... 7
1.8.2 BIOS (JCMOS1) ........................................................................... 7
Table 1.3: Clear BIOS CMOS (JCMOS1).................................... 7
1.8.3 ME Enable (JME1)........................................................................ 7
Table 1.4: JCMOS1/JME1: Clear CMOS/ME FW Update........... 7
1.8.4 JFP1.............................................................................................. 8
Table 1.5: JFP1 ........................................................................... 8
1.8.5 JWDT1 .......................................................................................... 8
Table 1.6: JWDT1........................................................................ 8
1.8.6 SW1 .............................................................................................. 8
Table 1.7: SW1............................................................................ 8
1.8.7 AT(1-2) / ATX(2-3) Mode Selector (PSON1) ................................ 8
Table 1.8: PSON1 ....................................................................... 8
1.9 System Memory ........................................................................................ 9
Chapter 2 Connecting Peripherals ....................11
2.1 Introduction ............................................................................................. 12
2.2 LAN and USB Ports (USB3C1, USB2C1)............................................... 12
Table 2.1: USB 3.0 Connector Pin Assignment......................... 12
Table 2.2: USB 2.0 Connector Pin Assignment......................... 13
2.3 VGA Connector (VGA1), HDMI Connector (HDMI1)............................... 13
Table 2.3: VGA Connector (VGA1) ........................................... 13
Table 2.4: HDMI Receptacle Connector.................................... 14
2.4 Line Out, Mic In Connector (AUDIO1)..................................................... 14
Table 2.5: Audio Connector Pin Assignments ........................... 14
2.5 Serial Ports (COM12).............................................................................. 15
Table 2.6: RS-232 Serial Port (COM12).................................... 15
2.6 CPU Fan Connector (CPUFAN1)............................................................ 16
Table 2.7: CPU Fan Power Connector(CPUFAN1)................... 16
2.7 GPIO Header (GPIO1) ............................................................................ 17
Table 2.8: GPIO Header (GPIO1) ............................................. 17
2.8 Case Open Connector (JCASE1) ........................................................... 18

PCE-2033/2133 User Manual ii
Table 2.9: JCASE1.................................................................... 18
2.9 Serial ATA Interface (SATA1~SATA2).................................................... 18
Chapter 3 AMI BIOS Setup................................. 19
3.1 Introduction ............................................................................................. 20
Figure 3.1 Setup Program Initial Screen ................................... 20
3.2 Entering Setup ........................................................................................ 21
3.2.1 Main Setup.................................................................................. 21
Figure 3.2 Main Setup Screen................................................... 21
3.2.2 Advanced BIOS Features Setup................................................. 22
Figure 3.3 Advanced BIOS Features Setup .............................. 22
Figure 3.4 Platform Misc. Configuration .................................... 23
Figure 3.5 CPU Configuration ................................................... 23
Figure 3.6 Power & Performance .............................................. 25
Figure 3.7 PCH-FW Configuration............................................. 26
Figure 3.8 AMT Configuration ................................................... 26
Figure 3.9 ASF Configuration .................................................... 27
Figure 3.10 Secure Erase Configuration .................................... 27
Figure 3.11 Firmware Update Configuration .............................. 28
Figure 3.12 PTT Configuration ................................................... 28
Figure 3.13 Trusted Computing.................................................. 29
Figure 3.14 ACPI Settings .......................................................... 29
Figure 3.15 SMART Settings...................................................... 30
Figure 3.16 Super IO Configuration............................................ 31
Figure 3.17 HW Monitor ............................................................. 32
Figure 3.18 Fan Configuration.................................................... 32
Figure 3.19 S5 RTC Wake Settings ........................................... 33
Figure 3.20 Serial Port Console Redirection .............................. 34
Figure 3.21 Legacy Console Redirection Settings ..................... 34
Figure 3.22 PCI Subsystem Settings.......................................... 35
Figure 3.23 Intel TXT Information............................................... 35
Figure 3.24 USB Configuration................................................... 36
Figure 3.25 Network Stack Configuration................................... 37
Figure 3.26 CSM Configuration .................................................. 37
Figure 3.27 NVMe Configuration ................................................ 38
3.2.3 Chipset........................................................................................ 39
Figure 3.28 Chipset .................................................................... 39
Figure 3.29 System Agent (SA) Configuration ........................... 39
Figure 3.30 Memory Configuration ............................................. 40
Figure 3.31 Graphics Configuration............................................ 40
Figure 3.32 VMD Setup Menu .................................................... 41
Figure 3.33 PCH IO Configuration.............................................. 41
Figure 3.34 PCI Express Configuration ...................................... 43
Figure 3.35 PCI Express Root Port Settings .............................. 43
Figure 3.36 SATA And RST Configuration ................................. 44
Figure 3.37 Security Configuration ............................................. 45
Figure 3.38 HD Audio Configuration........................................... 46
3.2.4 Security....................................................................................... 47
Figure 3.39 Security ................................................................... 47
3.2.5 Boot ............................................................................................ 48
Figure 3.40 Boot ......................................................................... 48
3.2.6 Save & Exit ................................................................................. 49
Figure 3.41 Save & Exit.............................................................. 49
Chapter 4 Value-Added Software Services ...... 51
4.1 Value-Added Software Services ............................................................. 52
4.1.1 Software API............................................................................... 52

iii PCE-2033/2133 User Manual
Chapter 5 Chipset Software Installation Utility 53
5.1 Before You Begin.................................................................................... 54
5.2 Introduction ............................................................................................. 54
5.3 Windows Driver Setup............................................................................. 54
Chapter 6 Integrated Graphic Device Setup .....55
6.1 Introduction ............................................................................................. 56
6.2 Windows Driver Setup............................................................................. 56
Chapter 7 LAN Configuration.............................57
7.1 Introduction ............................................................................................. 58
7.2 Features .................................................................................................. 58
7.3 Installation ............................................................................................... 58
7.4 Windows Driver Setup............................................................................. 58
Chapter 8 Intel ME...............................................59
8.1 Introduction ............................................................................................. 60
8.2 Installation ............................................................................................... 60
Chapter 9 SATA RAID Setup ..............................61
9.1 Introduction ............................................................................................. 62
9.2 SATA RAID Driver and Utility Setup ....................................................... 62
Chapter 10 HD Audio ............................................63
10.1 Introduction ............................................................................................. 64
10.2 Installation ............................................................................................... 64
Appendix A Programming the Watchdog Timer..65
A.1 Introduction ............................................................................................. 66
A.1.1 Watchdog Timer Overview.......................................................... 66
A.1.2 Programming the Watchdog Timer ............................................. 66
Table A.1: Watchdog Timer Registers ....................................... 67
A.1.3 Example Program ....................................................................... 68
Appendix B Programming the GPIO.....................73
B.1 Supported GPIO Register ....................................................................... 74
B.2 GPIO Registers ....................................................................................... 74
B.3 GPIO Example Program ......................................................................... 75

PCE-2033/2133 User Manual iv

Chapter 1
1Hardware
Configuration

PCE-2033/2133 User Manual 2
1.1 Introduction
The Advantech PCE-2033/2133 CPU board is engineered for demanding industrial
applications that demand robust computing capabilities in a remarkably compact
form factor. This CPU board is fully compatible with 12th/13th generation Intel®
Core™ i9/i7/i5/i3 processors and supports DDR5 4800 memory configurations of up
to 64GB. Notably, the PCE-2033/2133 offers cost-effective integrated graphics with a
maximum shared memory capacity of up to half the total system memory.
In terms of connectivity, the PCE-2033/2133 boasts an extensive range of I/O
options, including 2 x LAN ports, 8 x USB ports, dual display outputs, 2 x COM ports,
and 2~4 full-height expansion slots. Its single-side I/O design minimizes the space
requirements for deployment, streamlining both cabling and maintenance.
Furthermore, the modular design of the PCE-2033/2133 allows users to configure
their systems with flexibility. For added versatility, this CPU board can be seamlessly
integrated with Advantech's IPC-200 Series ultra-compact IPC chassis, catering to a
wide spectrum of application requirements.
1.2 Features & Benefits
Processor support: Intel 12th/ 13th generation family processors with the lat-
est 10nm lithography.
DDR5 4800 up to 64GB: DDR5 provide up to 50 percent increased perfor-
mance and bandwidth while saving up to 20 percent power.
Storage: Support SATA 3.0 ports with 600MB/s transfer rate.
High Performance I/O capability: Provides high transfer data performance
interface; USB 3.0 data transfer rate is 5 Gbps which is 10 times faster than
USB 2.0.
SUSI API: Supports SUSIAccess and Intelligent system module for remote
management.
1.3 Specifications
1.3.1 System
CPU: LGA-1700-socket Core i9/i7/i5/i3, Pentium and Celeron series proces-
sors.
L2 Cache: Please refer to CPU specification for detailed information.
BIOS: AMI 256Mbit SPI
System Chipset: Intel Q670E (PCE-2133), Intel H610E (PCE-2033)
SATA hard disk drive interface: PCE-2033 supports three SATA 3.0 ports (2
SATA ports via gold finger to backplane), and PCE-2133 supports four SATA 3.0
ports (2 SATA ports via gold finger to backplane).
1.3.2 Memory
RAM: Up to 64 GB in two 262-pin SO-DIMM sockets. Supports dual-channel
DDR5 4800 SDRAM WITHOUT ECC function.
Note! Due to the inherent limitations of the PC architecture, the system may
not fully detect the exact capacity of RAM installed.

3 PCE-2033/2133 User Manual
Chapter 1 Hardware Configuration
1.3.3 Input/Output
PCIe bus:
–PCE-2033: 1 x PCIe x16 from CPU, 1 x PCIe x4 and 1 x PCIe x1 from PCH.
–PCE-2133: 1 x PCIe x16 or 2 x PCIe x8 from CPU, and 3 x PCIe x4 and 1 x
PCIe x1 from PCH.
Serial ports: 2 x RS-232/422/485 serial ports.
USB port:
–PCE-2033: 4 x USB 3.2 Gen1 and 4 x USB 2.0
–PCE-2133: 8 x USB 3.2 Gen2
GPIO: Supports 8-bit GPIO from super I/O for general purpose control applica-
tion.
1.3.4 Graphics
Controller: Intel® HD Graphics embedded on processor.
Display memory: Shared memory is subject to OS (install 2 GB or above mem-
ory for basic system configuration).
VGA: 1920 x 1080 @ 60Hz.
HDMI: Up to 3840 x 2160 @ 60Hz
DP: Up to 4096 x 2160 @ 60Hz via optional cable
DVI: Up to 1920 x 1080 @ 60Hz via optional cable
PCI express x16 slot on the backplane: An external graphic card can be
installed in the PCIe x16 slot for high 2D/3D graphics capabilities.
1.3.5 Ethernet LAN
Supports single/dual 10/100/1000 Mbps Ethernet port(s) via the dedicated PCI
Express x1 bus which provides a 500 MB/s data transmission rate.
Controller:
–PCE-2033:
LAN1: I219V
LAN2: I226V
–PCE-2133:
LAN1: I219LM
LAN2: I226V
1.3.6 Industrial Features
Watchdog timer: Can generate a system reset. The watchdog timer is pro-
grammable, with each unit equal to one second or one minute (255 levels).
1.3.7 Mechanical and Environmental Specifications
Operating temperature: 0 ~ 60°C (32 ~ 140°F, depending on CPU and thermal
solution)
Storage temperature: -40 ~ 85°C (-40 ~ 185° F)
Operating humidity: 40°C @ 95% RH, non-condensing
Non-operating humidity: 60°C @ 95% RH, non-condensing
Power supply voltage: +3.3 V, +5 V, +12 V, +5 VSB
Board size: 188.6 x 127 mm
Board weight: 0.4 kg (weight of board)

PCE-2033/2133 User Manual 4
1.4 Jumpers and Connectors
Connectors on the PCE-2033/2133 CPU board link it to external devices such as
hard disk drives or a keyboard. In addition, the board has a number of jumpers used
to configure your system for your application.
The tables below list the function of each of jumpers and connectors. Later sections
in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for
connecting external devices to your CPU board.
Table 1.1: Jumper List
Label Function
JCASE1 Case open connector
JCMOS1 CMOS clear jumper
JFP1 Power Switch / Reset connector
JME1 Intel ME Enable/Disable jumper
JSMB1 Reserved for RD debug
JWDT1 Watchdog Reset
PSON1 AT(1-2) / ATX(2-3) mode selector
SW1 USB power mode, H/W monitor alarm mode and VGA mode
change
Table 1.2: Connectors
Label Function
AUDIO1 Audio connector (Line-out, Mic-In)
COM12 2 x RS232/422/485
CPUFAN1 CPU FAN connector (4-pin)
DIMMA1 DDR5 SODIMM slot
DIMMB1 DDR5 SODIMM slot
DP1 3rd Display output
GPIO1 8-bit digital I/O connector
HDMI1 HDMI connector
LAN1_USB3C1 PCE-2033: LAN, 2 x USB 3.2 Gen1
PCE-2133: LAN, 2 x USB 3.2 Gen2
LAN2_USB3C1 PCE-2033: LAN, 2 x USB 3.2 Gen1
PCE-2133: LAN, 2 x USB 3.2 Gen2
MINIPCIE1 Mini PCIe connector
SATA1~2 Serial ATA connector for storage
SPI1 SPI flash card pin header for BIOS
SW2 Power ON/Off switch
USB2H1 2 x USB 2.0 (PCE-2133 only)
USB3C1 4 x USB 3.2 Gen2 (PCE-2133 only)
USB2C1 4 x USB 2.0 (PCE-2033 only)
VGA1 VGA display output

5 PCE-2033/2133 User Manual
Chapter 1 Hardware Configuration
1.5 Board Layout: Jumper and Connector
Locations
Figure 1.1 Jumper and Connector Locations
Figure 1.2 Jumper and Connector Locations
1.5 Board Layout: Jumper and Connector Locations
)LJXUH-XPSHUDQG&RQQHFWRU/RFDWLRQV
ESPI1 NVME1 (PCE-2133 only)

PCE-2033/2133 User Manual 6
1.6 Block Diagram
Figure 1.3 PCE-2033/2133 Block Diagram
1.7 Safety Precautions
PCIeX1 Gen3
USB2.0*2
HDMI DVI
FRONT PANEL
Audio Jack
(MIC-in/Line-out) LINE OUT&MIC
FRONT PANEL
Internal PH
FRONT PANEL
Internal PH. (PCE-2133Only)
Level-Shift DDR5 4800
DDI1 Channel 0
DDR5 4800
Channel 1
NVME M.2 (PCE-2133 Only)
PCE-2133: 4 x USB 3.2 Gen2
PCE-2033: 4 x USB 2.0
PCIe x4 Gen4.0
2 PCIe x16 GF
To BP
PCIe x16 Gen4.0
VGA VGA Converter
Chrontel CH7517A-BF
2 USB 2.0 (Header)
SPI BIOS
eDP
PEG
USB 2.0*2
SATA Gen3*2
PCIe Gen3*10
Type A Dongle
3rd Display Pin Header DDI2
LGA1700
12th/13th Gen
Intel Core
Processor
Intel PCH
PCE-2133: Q670E
PCE-2033: H610E
DMI
Gen 4.0
FRONT PANEL
LAN1:
PCE-2133: I219LM
PCE-2033: I219V
MDI LAN1+
2 x USB 3.2
FRONT PANEL
PCIeX1 Gen3
USB 3.0 *2, USB2.0*2
LAN2: Intel I226V
SATA3.0
USB 2.0*2
TPM 2.0
SUPER I/O
NCT6126D
WATCH DOG TIMER
CASE OPEN
2 RS-232/422/485
GPIO
eSPI BUS
Realtek
ALC888S HD AUDIO
SPI BUS
COM1, 2
GPIO0
SATA1 Conn.
MDI LAN2 + 2 x USB 3.2
PCIeX1 Gen3/Gen2 /SATA3.0
PCIE/SATA/USB2.0
mSATA(H610E)
(Q670E)
1 Mini PCIe Slot
FRONT PANEL
Internal Conn.
Internal Conn.
SATA3.0 SATA2 Conn. Internal Conn.
(PCE-2133 Only)
Warning! Always completely disconnect the power cord from your chassis when-
ever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sud-
den power surges. Only experienced electronics personnel should open
the PC chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to static
electrical discharges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
Caution! The computer is provided with a battery-powered Real-time Clock.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to manufacturer's instructions.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.

7 PCE-2033/2133 User Manual
Chapter 1 Hardware Configuration
1.8 Jumper Settings
This section provides instructions on how to configure your motherboard by setting
the jumpers. It also includes the motherboard’s default settings and your options for
each jumper.
1.8.1 How to Set Jumpers
You can configure your motherboard to match the needs of your application by set-
ting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2 and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set-
ting jumpers.
1.8.2 BIOS (JCMOS1)
The PCE-2033/2133 CPU board contains a jumper that can erase BIOS CMOS data
and reset the system BIOS information. Normally this jumper should be set with pins
1-2 closed. If you want to reset them, set JCMOS1 to 2-3 closed for just a few sec-
onds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS to its last status or default setting.
1.8.3 ME Enable (JME1)
The PCE-2033/2133 CPU board contains a jumper that can enable ME data. Nor-
mally this jumper should be set with pins 1-2 closed, then you can see ME informa-
tion shows in BIOS menu. If you want to disable ME temporarily for firmware update,
set JME1 to 2-3 closed.
Table 1.3: Clear BIOS CMOS (JCMOS1)
Function Jumper Setting
*Keep BIOS CMOS data
Clear BIOS CMOS data
* default setting
1-2 closed
1
2-3 closed
1
Table 1.4: JCMOS1/JME1: Clear CMOS/ME FW Update
Function Jumper Setting
* ME enabled
ME disabled
* default setting
1-2 closed
1
2-3 closed
1

PCE-2033/2133 User Manual 8
1.8.4 JFP1
1.8.5 JWDT1
1.8.6 SW1
1.8.7 AT(1-2) / ATX(2-3) Mode Selector (PSON1)
Table 1.5: JFP1
Pin Function
1 Power On Off
2, 4 Ground
3 System Reset
5 Clear Watchdog
Table 1.6: JWDT1
Closed Pins Result
1-2 Reserved
2-3* Watch Dog Timer Reset
* default setting
Table 1.7: SW1
Switch State Setting
1 1* - 8 LAN1_USB2C1 & LAN2_USB3C1 do not provide standby charging
2 2* - 7 USB3C1 does not provide standby charging
3 3* - 6 HW monitor alarm beep
4 4* - 5 VGA always on. VGA will be ON when a cable is detected
* default setting
Table 1.8: PSON1
Closed Pins Result
1 VCCAT
2 +V3.3_JUMP
3 VCCATX

9 PCE-2033/2133 User Manual
Chapter 1 Hardware Configuration
1.9 System Memory
PCE-2033/2133 has two 262-pin memory sockets for DDR5 4800 MHz memory
modules with a maximum capacity of 64 GB. (Maximum 32 GB for each DIMM)
Note! Both PCE-2033 and PCE-2133 do NOT support registered DIMMs
(RDIMMs).

PCE-2033/2133 User Manual 10

Chapter 2
2Connecting
Peripherals

PCE-2033/2133 User Manual 12
2.1 Introduction
You can access most of the connectors from the top of the board. If you have a num-
ber of cards installed, you may need to partially remove a card to make all the con-
nections.
2.2 LAN and USB Ports (USB3C1, USB2C1)
PCE-2033/2133 provides up to 10 x USB ports with complete plug & play and hot
swap support. These USB ports comply with USB specifications 2.0 and 3.0, support
transfer rates up to 480 Mbps (USB2.0), and 10 Gbps (USB 3.2 Gen2). Eight ports
are located on the I/O bracket, and the other two USB ports are located on the back-
plane via gold finger. PCE-2033/2133 is equipped with two high-performance 1000
Mbps and 2500 Mbps Ethernet LANs.
Table 2.1: USB 3.0 Connector Pin Assignment
Pin Signal
1 +5V
2 USB Data-
3 USB Data+
4 GND
5 SSRX-
6 SSRX+
7 GND
8 SSTX-
9 SSTX+
PCE-2133: USB3C1
LAN2_USB3C1
LAN1_USB3C1
PCE-2033: USB2C1