Advantech FWA-1211 Installation and operation manual

FWA-1211 Startup Manual 1
Before installation, ensure that the following materials have
been received:
• One FWA-1211 din-rail Platform
• One box of accessories
• Onewarrantycerticate
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1:AcrobatReaderisrequiredtoviewanyPDFle
Acrobat Reader can be downloaded at: www.
adobe.com/Products/acrobat/readstep2.html
(Acrobat is a trademark of Adobe).
Note 2:Suppliedbycertiedpowersupply:
FSP040-RHAN2
ADP-40GD BH
Industrial Grade Cyber Security Appliance based on
Intel® Atom™ x5-E3940/ x5-E3930 Processor Platform
Startup Manual
Main Board Functions
• CPU: Intel Atom™ E3940/E3930
• BIOS: AMI™
• Memory: 1 x DDR3L 1333/1600/1867 MHz SODIMM, up
to 8 GB
• Ethernet:
- 5 x 10/100/1000 Mbps RJ45 via Intel i210-IT with 2
segment bypass
- 2 x10/100/1000 Mbps SFP via Intel i210-IS
• Storage: 1 x 2.5” internal SSD; 1 x mSATA slot (half size)
• Peripherals:
- USB:12x USB2.0 on front panel
- 2 x Power LED
- 1 x HDD LED
- 1 x Alarm LED
- 1 x Micro-HDMI
- 1 x Reset
- 1 x Console
- 2 x DB9 RS-232/422/485 seriel port (SKU option)
• Dimensions (W x L x H): 88 mm x 127 mm x 150 mm
• Weight: 3 Kg
• Environment: Operating Non-operating
• Temperature: -40 °C ~ 70 °C -40 °C ~ 85 °C
(-40 °F ~ 158 °F) (-40 °F ~ 185 °F)
• Altitude: Below 5000 m
• Humidity: 5% ~ 95%
• IP Rating: IP40
SpecicationsPacking List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com.tw/support
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the FWA-1211 series Rev. A.
Part No. 2002121100 1 st Edition
December 2020
Warning:
Pleasepowero󰀨themachineanddisconnectitfrom
all power source before you disassemble FWA-1211
machine.
This product is intended to be supplied by an UL Listed
power supply or dc source suitable for use at minimum
Tma 40 degree C whose output meets ES1, LPS, and
is rated 9-36Vdc, 4-1A. If need further assistance,
please contact Advantech for further information.

2 FWA-1211 Startup Manual
FWA-1211
Front view:
Back view:
Specication
Installation
Installing
1. Unfasten the screws (red arrows), take out and keep for
later, then loosen the screws circled in red and remove
the heatsink.
Installing the memory
1. Prepare the memory.
2. Insert into the slot as below and press the memory until
locked.

FWA-1211 Startup Manual 3
Installing the mSATA
1. Prepare the mSATA.
2. Insert the msata storage into the slot as below.
3. Take the screw from the assembly box.
4. Fix as below.
5. Take two thermal pads from the assembly box.
6. Replacetheheatsinkandxthescrewsasbelow.
7. Thenxthescrewsontheheatsink.
Installation (Cont.) Installation (Cont.)

4 FWA-1211 Startup Manual
Installing the SSD
1. Unfasten the screws (red arrows) and keep for future
use.
2. Take 4 screws out of the accessory box as below and
xtheSSDontothethebracket.
Installation (Cont.)
Installation (Cont.)
3. Take the SATA power cable from the accessory box,
then connect to the SSD.
4. Connect the SATA cable and the power cable as shown
below.
5. Route the cable to the side of the mainboard as shown
below.
6. Putontheheatsinkandxwththescrewsasshown
below.

FWA-1211 Startup Manual 5
Installing the DIN Rail
1. Take the screw and bracket out from the accessory box.
2. Install the screw and bracket as shown below.
3. Install the machine on the bracket accordingly.
Installation (Cont.) Jumpers and Connectors
The board has a number of jumpers that allow you to con-
gureyoursystemtosuityourapplication.Thetablebelow
lists the function of each of the jumpers and connectors.
Jumper/Connector List
Connector Name Function
SODIMM1 System memory expansion slot
for DDR3L SO-DIMM.
BAT1 Battery holder for coin battery
SATA1 SATA IO connector
SATA_PWR1 Power connector for SATA HDD
used
MSATA1 Half size mSATA connecter
8051_JTAG1 Programming 8051 pin header
LPC1 LPC bus connecter for TPM
module
LAN1, LAN2, LAN_
MAGT1 RJ45 LAN connectors
USB2_1 USB2.0 connectors
USB2_2 USB2.0 connectors
COM1 RJ45 console connector
HDMI-D1 Micro HDMI connector
SYS_RST1 System reset button
PWR_BTN1 Power button pin header
CN3 Power in pin header
Ex1 Extend board connecter
JCMOS1 Clear CMOS jumper
PSON1 AT/ATX mode select
Jumper Name Pin Default Setting Function
JCMOS1
1-2 Jumper short Normal status
2-3 open Clear CMOS
PSON1
1-2 Jumper short AT mode
2-3 open ATX mode

6 FWA-1211 Startup Manual
Clear CMOS Pin Header
Pin Number Pin Name Function
1 NC NC
2 RTEST Clear CMOS
3 GND Ground
AT/ATX Mode Selection Pin Header
Pin Number Pin Name Function
1AT Enable AT mode
2 V3.3_net 3.3V level net
3VATX Enable ATX mode
Battery Holder for Coin Battery
Pin Number Pin Name Function
1 VBAT1 3V battery power
2 GND Ground
JCMOS1
PH_3x1V_2.00mm
1
2
3
JCMOS1
PH_3x1V_2.00mm
1
2
3
PSON1
PH_3x1V_2.00mm
1 2 3
BAT1
W_2V_1.25mm
1
2
Jumpers and Connectors (Cont.)
SATA Connector
Pin Number Pin Name Function
1 GND Ground
2 TX+ TX+ Signal of SATA
3 TX- TX- Signal of SATA
4 GND Ground
5 RX- RX+ Signal of SATA
6 RX+ RX- Signal of SATA
7 GND Ground
SATA Power Connector (SATA_PWR1)
Pin Number Pin Name Function
1 VCC 5V power
2 GND Ground
3 GND Ground
4 +V12 12V power
Power Button Signal Pin Header
Pin Number Pin Name Function
1 PANSWIN# Power button signal
2 GND Ground
GND
TX+
TX-
GND
RX-
RX+
GND
SATA1
<Characteristic>
1
2
3
4
5
6
7
89
SATA_PWR1
W_4V_2.5mm
<Characteristic>
1
2
3
4
PWR_BTN1
WB_2V_2.00mm
1
2
Jumpers and Connectors (Cont.)

FWA-1211 Startup Manual 7
Power Board Connector (CN3)
Pin Number Pin Name Function
1 GND Ground
2 +V12_SB_S 12V standby power
3 GND Ground
4 +V12_SB_S 12V standby power
5 GND Ground
6 +V12_SB_S 12V standby power
7 GND Ground
8 PWRBTN_IN power button input signal
9 +V5_SB 5V standby power
10 PA_OK# Power good signal of
power A
11 +V5 5V system power
12 PB_OK# Power good signal of
power B
8051 _JTAG Pin Header
Pin Number Pin Name Function
1 RST/C2CK Reset 8051 & clock for
C2 interface
2 C2D data for C2 interface
3 GND Ground
CN3
PH(F)_6x2V_S2.0mm
1
3
5
7
9
11
2
4
6
8
1
0
1
2
8051_JTAG1
PH_3x1V_2.00mm
<Characteristic>
1
2
3
LPC Connector
Pin Number Pin Name Function
1L_FRAME#
LPC Frame signal
2 GND Ground
3 LAD0 LPC address pin 0
4 CLK LPC 25Mhz clock
5 LAD1 LPC address pin 1
6 SERIRQ LPC serial IRQ ouput
7 LAD2 LPC address pin 2
8 RESET LPC reset input
9 LAD3 LPC address pin 3
10 VCC3 3.3V power
RJ45 Console Port
Pin Number Pin Name Function
1RTS Signal of COM1 for
system console
2 DTR Signal of COM1 for
system console
3 TXD Signal of COM1 for
system console
4,5 GND Ground
6 RXD Signal of COM1 for
system console
7 DSR Signal of COM1 for
system console
8 CTS Signal of COM1 for
system console
LPC1
BH_5x2V_S2.00mm
1
3
5
7
9
2
4
6
8
1
0
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

8 FWA-1211 Startup Manual
Figure 1: Location List of Jumper and Connector on Mainboard
Jumpers and Connectors (Cont.)

FWA-1211 Startup Manual 9
The PWR board has a number of jumpers that allow you to
congureyoursystemtosuityourapplication.Thetablebe-
low lists the function of each of the jumpers and connectors.
Jumper/Connector List
Connector Name Function
DC_IN1 Power in connecter
CN1 main board connecter
PWR_BTN1 Power button connecter
Power in Connector
Pin Number Pin Name Function
1 PGND Ground
2 DC_A Power A input
3 ALM2 Signal of alerm2
4 ALM1 Signal of alerm1
5 PGND Ground
6 DC_B Power B input
DC_IN1
PLUG_6_5.00mm
<Characteristic>
1
2
3
4
5
6
Main Board Connector
Pin Number Pin Name Function
1 GND Ground
2 +V12_SB 12V standby power
3 GND Ground
4 +V12_SB 12V standby power
5 GND Ground
6 +V12_SB 12V standby power
7 GND Ground
8 PWRBTN_IN power button input signal
9 +V5_SB 5V standby power
10 PA_OK# Power good signal of
power A
11 0 5V system power
12 PB_OK# Power good signal of
power B
Power Button Connector
Pin Number Pin Name Function
1 PWRBTN_IN Signal of power button
2 GND Ground
CN1
PH_6x2V_S2.0mm
<Characteristic>
2
4 6 8 1
0
1
2
1
3 5 7 9
1
1
PWR_BTN1
WB_2V_2.00mm
1
2
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

10 FWA-1211 Startup Manual
Figure 2: Location List of Jumper and Connector on PWR Board
Jumpers and Connectors (Cont.)