Advantech PCM-3864 Installation and operation manual

Packing listPacking list
Packing listPacking list
Packing list
Before you begin installing your card, please make
sure that the following materials have been shipped:
• 1 PCM-3864/3860 All-in-one single board computer
• 1 Start-up manual
• 1 Floppy cable
• 1 3.5" IDE flat cable
• 1 DIN jack 5p-6p cable
• 1 secondary serial port cable (RS-232/422/485)
• 1 Parallel cable
• CD-ROM or Disks for utility, drivers, and manual (in
PDF format)
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note: For detailed contents of the
PCM-3864/3860, please refer to the
enclosed CD-ROM or Disk (in PDF format).
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service, please visit our support
website at:
http://support.advantech.com
This manual is for the PCM-3864/3860
Part No. 2006000032 1st edition
Printed in Taiwan July1999
PCM-3864/3860 386SBC with VGA/LCD
Start-up Manual
PCM-3864 386 SBC with VGA/ LCD
SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Standard SBC functions
•CPU with core logic: Ali M6117C, 40 MHz
80386SX processor
•BIOS: AMI 128 KB Flash memory
•RAM: One 72-pin SIMM socket. Supports FPM/
EDO DRAM 1 ~ 16 MB (accepts 1 / 4 / 16 MB
modules)
•Enhanced IDE hard disk drive interface:
Supports up to two enhanced IDE devices. BIOS
auto-detect
•Multi-mode parallel port: Configured to LPT1,
LPT2, LPT3 or disabled. Supports SPP/EPP/ECP
mode. D-SUB 25-pin connector on board
•Floppy disk interface: Supports up to two FDDs:
3.5" (720 KB or 1.44 MB) and/or 5.25" (360 KB or
1.2 MB)
•Serial ports: One serial RS-232 port, one serial
RS-232/422/485 port. Two 16C550 compatible
UARTs
•PS/2 Keyboard connector: Mini-DIN keyboard
connector
Digital I/O
•Digital input x 4: TTL compatible input voltage
High; 2.0 V minimum
Low: 0.8 V maximum
•Digital output x 4: TTL compatible output V
High: source 0.4 mA @ 2.4 V min.
low: sink 8 mA @ 0.5 V max.
SVGA/flat panel interface
•Chipset: C&T 65545
•Display memory: 512 KB DRAM
•Hardware Windows acceleration: 16-bit graphic
engine. Hardware line drawing and 64 x 64 x 2
hardware cursor
•Resolution: Panel resolution up to 640 x 480 @
256 colors. Non-interlaced CRT monitors
resolution up to 1024 x 768 @ 16 colors

2PCM-3864/3860 Start Up Manual
The board has a number of jumpers that allow you to
configure your system to suit your application.
The table below lists the function of each of the board
jumpers and connectors:
Jumpers
Label Function
J1 Enable watchdog timer
J3 Enable watchdog timer
J4 CMOS setup
J5 DIO port selector
J6 COM2 RS-232/422/485 selector
Connectors
Label Function
CN1 PC/104 connector
CN2 PC/104 connector
CN3 COM1 connector
CN4 COM2 connector
CN5 Digital I/O port
CN6 PS/2 keyboard connector
CN7 CRT display connector (PCM-3864 only)
CN8 Power connector (-5 V, -12 V)
CN9 Hard disk connector
CN10 Floppy disk connector
CN11 Parallel port connector
CN12 LCD connector (PCM-3864 only)
CN13 Power connector (+5 V, +12 V)
SW1 Reset switch
Jumper settings
J1 & J3: Watchdog timer enable/disable
enable *disable
J1
J3
Jumpers and connectorsJumpers and connectors
Jumpers and connectorsJumpers and connectors
Jumpers and connectors
J4
J3
J1 J5 J6
Mechanical and environmental
•Dimension (L x W): 145 mm x 102 mm (5.9" x 4.2")
•Power supply voltage: +5 V (4.75 ~ 5.25 V)
•Power requirements: +5 V @ 1.5 A (typical)
•Operating temperature: 0 ~ 60° C (32° ~ 140° F)
•Weight: 0.2 kg
J4: CMOS setup
*3.6 V battery on Clear CMOS
J4 1-2 2-3
J5: DIO port selector
*340 H 240 H
J5
J6: COM2 selector
*RS-232 RS-422 RS-485
J6
1
3
5
1
3
5
2
4
6
2
4
6
Locating Jumpers

Locating Connectors
CN10
CN8
CN11 CN12 CN9 CN13
SW1
CN7
CN6
CN5
SIMM1
CN3
CN4
CN1,CN2
PCM-3864 mechanical drawingPCM-3864 mechanical drawing
PCM-3864 mechanical drawingPCM-3864 mechanical drawing
PCM-3864 mechanical drawing