Advantech PCIE-1753 User manual

User Manual
PCIE-1753
96-Ch Digital I/O PCI Express
Card

PCIE-1753 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2023
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
Intel® and Pentium® are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2003E17511 Edition 2
Printed in Taiwan March 2023

iii PCIE-1753 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the
user manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference. In this
event, users are required to correct the interference at their own expense.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Have the follow-
ing information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

PCIE-1753 User Manual iv
Warnings, Cautions, and Notes
Document Feedback
To assist us with improving this manual, we welcome all comments and constructive
criticism. Please send all feedback in writing to [email protected].
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
1. To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
2. Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.
Warning! Warnings indicate conditions that if not observed can cause personal
injury!
Caution! Cautions are included to help prevent hardware damage and data
losses. For example,
“Batteries are at risk of exploding if incorrectly installed. Do not attempt
to recharge, force open, or heat the battery. Replace the battery only
with the same or equivalent type as recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.”

v PCIE-1753 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following occurs, have the equipment checked by service person-
nel:
–The power cord or plug is damaged.
–Liquid has penetrated the equipment.
–The equipment has been exposed to moisture.
–The equipment is malfunctioning, or does not operate according to the user
manual.
–The equipment has been dropped and damaged.
–The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -20 °C (-4 °F) or above 60 °C (140 °F) as this may damage the compo-
nents. The equipment should be kept in a controlled environment.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at
the operator’s position should not exceed 70 dB (A).
DISCLAIMER: These instructions are provided according to IEC 704-1 standards.
Advantech disclaims all responsibility for the accuracy of any statements contained
herein.

PCIE-1753 User Manual vi
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor über-
hitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt
werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es
sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in
das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-
lösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
–Netzkabel oder Netzstecker sind beschädigt.
–Flüssigkeit ist in das Gerät eingedrungen.
–Das Gerät war Feuchtigkeit ausgesetzt.
–Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
–Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
–Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz
nur durch densellben order einem vom Hersteller empfohlene-mahnlichen Typ.
Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht
fachmännische Weise gewechselt wird. Verfangen Sie die Batterie nur gleicher
oder entsprechender Type, wie vom Hersteller empfohlen. Entsorgen Sie Batte-
rien nach Anweisung des Herstellers.
17. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC-
704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in die-
sem Zusammenhang getätigten Aussagen ab.

vii PCIE-1753 User Manual
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Features .................................................................................................... 2
1.3 Applications............................................................................................... 3
1.4 Installation Guide ...................................................................................... 3
1.5 Accessories............................................................................................... 3
Chapter 2 Installation............................................5
2.1 Installation ................................................................................................. 6
2.2 Packing List............................................................................................... 6
2.3 Driver Installation ...................................................................................... 7
2.4 Software Utility .......................................................................................... 8
2.5 Software Development Using DAQNavi SDK ........................................... 8
2.6 FPGA Code Update .................................................................................. 8
2.7 Hardware Installation ................................................................................ 9
Figure 2.1 Device Manager ....................................................... 10
Chapter 3 Signal Connections ...........................11
3.1 Overview ................................................................................................. 12
3.2 Switch and Jumper Settings.................................................................... 12
Figure 3.1 Jumper and switch settings ...................................... 12
Figure 3.2 Selected jumper and switch settings ........................ 12
3.2.1 Keep Last Status (JP1)............................................................... 13
Table 3.1: Power-On Configuration (JP1) ................................. 13
3.2.2 Port Direction Settings (JP2~JP25) ............................................ 13
Table 3.2: DI/O Channel Direction Configuration (JP2 ~ JP25) 13
Table 3.3: Summary of Jumper Settings ................................... 14
3.2.3 Board ID (SW1)........................................................................... 15
Table 3.4: Board ID ................................................................... 15
3.3 Pin Assignment Connections .................................................................. 16
3.3.1 Digital Input (TTL DI, Pull-Up/-Down) ......................................... 18
Figure 3.3 Digital input signal connection.................................. 18
Figure 3.4 Digital input signal connection using a switch as inter-
nally pulled-up .......................................................... 19
Figure 3.5 Digital input signal connection using a switch as inter-
nally pulled-down...................................................... 20
3.3.2 Digital Output (TTL DO).............................................................. 21
Figure 3.6 Digital output signal connection............................... 21
Appendix A Specifications ....................................23
A.1 Digital Input ............................................................................................. 24
A.2 Digital Output .......................................................................................... 24
A.3 General ................................................................................................... 24
Appendix B Block Diagram ...................................25

PCIE-1753 User Manual viii

Chapter 1
1Overview

PCIE-1753 User Manual 2
1.1 Introduction
The PCIE-1753 is a 96-ch DI/O card with PCI Express bus. It provides 96 channels of
parallel digital input/output compatible with 5V/TTL. It emulates mode 0 of the 8255
PPI chip, but the buffered circuits offer a higher driving capability than the 8255.
The I/O channels are divided into twelve 8-bit ports. Each port can be divided into two
nibbles (bits 0 ~ 3 belong to the low nibble, while bits 4 ~ 7 belong to the high nibble).
You can configure each nibble as either input or output via software. The interrupt
handling capability provides users the flexibility to generate interrupts to a PC. This
card uses a high-density SCSI 100-pin connector for easy and reliable connections to
field devices.
Two other features give the PCIE-1753 practical advantages in an industrial setting.
When the system is hot reset (the power is not turned off) PCIE-1753 retains the last
I/O port settings and output values if the user has set jumper JP1 to enable this fea-
ture. Otherwise, port settings and output values reset to their default state, or to the
state determined by other jumper settings. The PCIE-1753’s other useful feature is it
supports both wet and dry contacts for digital input channels, allowing it to interface
with other devices more easily.
The following sections of this chapter will provide further information about features,
an installation guide, and some brief information on software and accessories for the
PCIE-1753 card.
1.2 Features
96 TTL digital I/O lines
Interrupt handling capability
Supports both dry and wet contact for digital input channels
Keeps the I/O port settings and DO state after a hot reset
BoardID switch
Pattern match interrupt function for DI
“Change of state” interrupt function for DI
Programmable digital filter function for DI (available for bit 0 of every port)
The Advantech PCIE-1753 offers the following main features:
Plug-and-Play Function
The PCIE-1753 is a Plug-and-Play device, which fully complies with PCI Express
Specifications. During card installation, there is no need to set jumpers or DIP
switches. Instead, all bus-related configurations such as base I/O address and inter-
rupt are automatically done by the Plug-and-Play function.
Board ID
The PCIE-1753 has a built-in DIP Switch that helps define each card’s ID when multi-
ple PCIE-1753 cards have been installed on the same PC chassis. The board ID set-
ting function is very useful when users build their system with multiple PCIE-1753
cards. With correct Board ID settings, you can easily identify and access each card
during hardware configuration and software programming.
Digital Filter for Digital Input Channels
The PCIE-1753 includes a programmable digital filter on channel 0 (bit 0) on each
port to eliminate the unexpected signal or noise from the card's inputs. When the dig-
ital filter is enabled, the state of the corresponding input channel will not update
immediately until the signal is stable for a period of time which is programmed by the
user.