Advantech UNO-3300G Series User manual

User Manual
UNO-3300G Series
Intel® Core® i7/Celeron
Processors Embedded
Automation PC, with 2x PCI(e)/
PCI Extension Slots

UNO-3300G Series User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2016
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel® is trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
C&T is a trademark of Chips and Technologies, Inc.
All other product names or trademarks are properties of their respective owners.
This manual applies to the below model which is abbreviated as UNO-3300G series
products in this article.
UNO-3382G
UNO-3384G
PN: 2003U30000 Edition 1
Printed in Taiwan June 2016

iii UNO-3300G Series User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
警告使用者：這是甲類資訊產品，在居住的環境中使用時， 可能會造成射頻干擾，在
這種情況下，使用者會被要求採取某些適當對策。

UNO-3300G Series User Manual iv
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

v UNO-3300G Series User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the
user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
17. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

UNO-3300G Series User Manual vi
Safety Instructions
Manufacturer
ADVANTECH CO., LTD.
1, ALLEY 20, LANE 26, RUEIGUANG ROAD, NEIHU DISTRICT, TAIPEI 114, TAI-
WAN
Connection for AC mains:
Power installation must be performed with qualified electrician and followed with
National Electrical Code, ANSI/NFPA 70 and Canadian Electrical Code, Part I, CSA
C22.1.
Use No. 18 AWG, 90°C copper wire with TBS, SA, SIS, FEP, FEPB, MI, RHH, RHW-
2, THHN, THHW, THW-2, THWN-2, USE-2, XHH, XHHW, XHHW-2 or ZW-2 type
pressure terminal connector and 4.5 lb-in Torque force when connecting to terminal
block.
Unit shall be connected to readily accessible Branch Circuit Breaker which rated 20 A
Connection for DC power source:
This product is intended to be supplied by a Listed Power Adapter or DC power
source, rated 24Vdc, 4.2A minimum and Tma 55 degree C, if need further assis-
tance, please contact Advantech for further information.
impact rigid = with an impact rating of at least IK09
The enclosure shall be made of metal (except magnesium) or of non-metallic materi-
als having a flammability classification V-1, or better.
Potential for explosion
The device must be installed in an end-use enclosure, which can only be opened by
using a tool (a tool-secured enclosure).
Failure to follow these instructions will result in death or serious injury.
Caution! Wiring minimum temperature 85 degree C.
Prudence! Câblage température minimale de 85 degrés C

vii UNO-3300G Series User Manual
Caution! 1. If the equipment is used in a manner not specified by the manufac-
turer, the protection provided by the equipment may be impaired.
2. Any parts which are required to be examined or supplied only by
the manufacturer or agent.
3. The computer is provided with a battery-powered real-time clock
circuit. There is a danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type recom-
mended by the manufacture. Discard used batteries according to
the manufacturer's instructions.
Prudence! 1. Si l'équipement est utilisé d'une manière non spécifiée par le fabri-
cant, la protection fournie par l'équipement peut être altérée.
2. Toutes les pièces qui doivent être examinés ou fournis que par le
fabricant ou l'agent.
3. L'ordinateur est muni d'un circuit en temps réel de l'horloge alimen-
tée par batterie. Il y a un risque d'explosion si la batterie est rem-
placée de façon incorrecte. Remplacez uniquement avec le type
identique ou équivalent recommandé par le fabricant. Jetez les
piles usagées conformément aux instructions du fabricant.

UNO-3300G Series User Manual viii

ix UNO-3300G Series User Manual
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Hardware Specifications ........................................................................... 2
1.2.1 General ......................................................................................... 2
1.3 System Hardware...................................................................................... 3
1.3.1 I/O Interfaces ................................................................................ 3
1.3.2 Environment.................................................................................. 4
1.3.3 Expansion Board (Optional).......................................................... 4
1.4 Safety Precautions .................................................................................... 4
1.5 Chassis Dimensions.................................................................................. 5
Figure 1.1 UNO-3382G Dimensions............................................ 5
Figure 1.2 UNO-3384G Dimensions............................................ 5
1.6 Accessories............................................................................................... 5
Chapter 2 Hardware Functionality.......................7
2.1 Introduction ............................................................................................... 8
Figure 2.1 UNO-3382G Dimensions............................................ 8
Figure 2.2 UNO-3384G Dimensions............................................ 8
Figure 2.3 UNO-3382G Bottom View .......................................... 9
Figure 2.4 UNO-3382G Front View ............................................. 9
Figure 2.5 UNO-3384G Bottom View .......................................... 9
Figure 2.6 UNO-3384G Front View ............................................. 9
2.2 Serial Interface (COM1) .......................................................................... 10
Figure 2.7 Pin header of COM1................................................. 10
2.2.1 RS-232/422/485 Interface (COM1) ............................................. 10
2.2.2 To switch the internal SW1/SW2 according to the placement .... 11
Figure 2.8 Location .................................................................... 11
Figure 2.9 Without termination................................................... 11
Figure 2.10With termination........................................................ 12
2.3 LAN: Ethernet Connector ........................................................................ 12
2.4 Power Connector .................................................................................... 12
2.5 USB Connector ....................................................................................... 12
2.6 Display Connector................................................................................... 12
2.7 RTC Battery ............................................................................................ 13
2.8 Power Button/Power Management ......................................................... 13
2.8.1 Power mode switch..................................................................... 13
Figure 2.11AT/ATX adjustment .................................................. 13
2.9 Reset Button ........................................................................................... 13
2.10 PCI Express Mini Card Socket................................................................ 14
Figure 2.12PCIE mini card sockets placement........................... 14
2.10.1 iDoor Expansion Slot .................................................................. 14
2.11 PCIe Slot ................................................................................................. 14
2.12 SATA HDD Drive..................................................................................... 15
Figure 2.13SATA Mode Selection .............................................. 15
Figure 2.14Detecting a RAID configuration ................................ 16
Figure 2.15Creating a RAID Volume .......................................... 16
2.13 Audio Jack............................................................................................... 16
2.14 LED Indicators......................................................................................... 17
Chapter 3 Initial Setup ........................................19
3.1 Connecting Power................................................................................... 20

UNO-3300G Series User Manual x
Figure 3.1 Power Connector...................................................... 20
3.2 Inserting an iDoor Module....................................................................... 20
3.3 Installing a Hard Disk .............................................................................. 22
3.4 Installing an Interface card...................................................................... 23
3.5 Installing Power Cable ............................................................................ 24
3.6 Mounting UNO-3300G Series ................................................................. 25
Figure 3.2 Book mount .............................................................. 25
Figure 3.3 Wall mount ............................................................... 26
Figure 3.4 Detachable PC (Optional)_01 .................................. 27
Figure 3.5 Detachable PC (Optional)_02 .................................. 27
Appendix A System Settings and Pin Assignments
............................................................ 29
A.1 System I/O Address and Interrupt Assignment....................................... 30
Table A.1: Interrupt Assignments .............................................. 30
A.2 Board Connectors and Switches............................................................. 30
Figure A.1 Bottom view of System board................................... 30
Figure A.2 Front view of Main/System board............................. 31
A.3 Function of connectors & switches ......................................................... 31
Table A.2: Connectors on System board................................... 31
Table A.3: Connectors on System board................................... 32
A.4 Audio (Pin header) .................................................................................. 32
Table A.4: CN16 Audio .............................................................. 32
A.5 Internal USB............................................................................................ 33
Table A.5: CN20 Internal USB................................................... 33
A.6 COM1...................................................................................................... 33
Table A.6: CN35 COM1............................................................. 33
A.7 LAN1/LAN2 ............................................................................................. 34
Table A.7: CN29 LAN1/LAN2 .................................................... 34
A.8 External USB3.0 ..................................................................................... 35
Table A.8: CN5 External USB3.0............................................... 35
A.9 External USB2.0 ..................................................................................... 36
Table A.9: CN34 External USB2.0............................................. 36
A.10 DISPLAYPORT....................................................................................... 37
Table A.10:CN14 DISPLAYPORT .............................................. 37
A.11 HDMI....................................................................................................... 38
Table A.11:CN36 HDMI .............................................................. 38
A.12 Power Connector (PWR) ........................................................................ 39
Table A.12:Power connector pin assignments ........................... 39
Table A.13:SW7 Power Switch................................................... 39
Table A.14:SW8 Reset ............................................................... 39
Table A.15:CN8 CFast................................................................ 40
Table A.16:CN6/CN7 Mini PCIE ................................................. 41
Table A.17:: CN9 mSATA........................................................... 42
Table A.18:PCN1: reserve for power output, the voltage is same as
power input (CN1) .................................................... 44

Chapter 1
1Overview
This chapter provides an overview
of UNO-3300G series' specifica-
tions.
Sections include:
Introduction
Hardware specification
Safety precautions
Chassis dimensions
Accessories

UNO-3300G Series User Manual 2
1.1 Introduction
AAdvantech's UNO-3300G series offer an open and universal automation
solution. The newest UNO-3300 series of the Control Cabinet PC have attractive
and flexible extension capabilities such as 2 x USB2.0 & 2 x USB3.0 port, 1 x
HDMI, 1 x DP, 1 x COM port, 2 x LAN ports, 2 x mPCIe. UNO-3384G
also supports 1 x PCIex4 & 1 x PCI expansion. It's a reliable industrial
control machine certified by industrial automation standard IEC-61010.
1.2 Hardware Specifications
1.2.1 General
Certification:
–CE, FCC, UL, CB, IEC-61010, UL-61010
Dimensions (W×D×H):
–UNO-3382G: 254 x 65.2 x 207 mm (10'' x 2.5'' x 8.15'') Aluminum
–UNO-3384G: 254 x 103.2 x 207 mm (10'' x 4.06'' x 8.15'') Aluminum
Mounting: Book mount
Power Consumption: 45W (Typical, no card added)
Power Requirements: 24 VDC, support AT/ATX power mode
BIOS AT simulation mode (support system reboot automatically after power
recovery)
Weight: UNO-3382G: 3.1kg, UNO-3384G: 3.9kg
OS Support: Windows7/8, WES7, Advantech Linux
System Design: Fanless

3 UNO-3300G Series User Manual
Chapter 1 Overview
1.3 System Hardware
CPU:
–UNO-3382G-474AE: Intel Core® i7-4650U (4M Cache, 1.7GHz)
–UNO-3384G-474AE: Intel Core® i7-4650U (4M Cache, 1.7GHz)
–UNO-3382G-4C3AE: Intel Celeron 2980U (2M Cache, 1.6GHz)
–UNO-3384G-4C3AE: Intel Celeron 2980U (2M Cache, 1.6GHz)
Memory: 8G/4G DDR3L built-in
Indicators: Six LEDs for power, battery, HDD, COM (active status)
Storage: HDD: 2 × 2.5" SATAHDD/SSD bays, support SATAGen3.0
Display: 1 ×DP,1 ×HDMI (support 2 independent displays) 1920*1200
Watchdog Timer: 256 levels time interval, programmable from 1 to 255
sec
Expansion Slots:
–UNO-3382G: 2 Full-size mPCIe
–UNO-3384G: 2 Full-size mPCIe, 1x PCIex4, 1x PCIx1
PCIE max speed is 5GT/s; PCI max speed is 66MHz; system can provide
typical 10W for each PCI/PCIE slot, Max 20W for single slot condition:
Each PCI/PCIE slot can support below power rail:
1.3.1 I/O Interfaces
Serial Ports: 1 x RS-232/422/485, DB9, auto flow control, 50 ~ 115.2 kbps
LAN Ports: 2 x RJ45, 10/100/1000 Mbps IEEE 802.3u 1000Base-T Fast
Ethernet
USB Ports: 4 x USB Ports (2 x USB 2.0, 2 x USB 3.0 compliant)
Displays: 1 x HDMI, supports 1920 x 1200 @ 60 Hz 24 bpp; 1 x DP, supports
3200 x 2000 @ 60 Hz 24 bpp
Power Connector: 1 x 3 Pin, Terminal Block
Condition Slot1 power Slot2 power Total Power limitation
(slot1 + slot2 power)
1typical 10W,
Max 20W NA <20W (Note1)
2NA typical 10W,
Max 20W <20W (Note1)
3typical 10W,
Max 20W
typical 10W,
Max 20W <20W (Note1)
Slot type A: 3.3V B: 5V C: 12V D:-12V Note
PCI slot typical 3.03A
Max 6.06A
typical 2A
Max 4A
typical 0.83A
Max 1.66A Max 0.5A
A+B+C+D,
total
power<20W
PCIE slot typical 3.03A
Max 6.06A
typical 2A
Max 4A
typical 0.83A
Max 1.66A N/A A+B+C, total
power<20W
Note! Total power consumption combined on PCI and PCIe slots should be
less than 20 Watt.

UNO-3300G Series User Manual 4
1.3.2 Environment
Relative Humidity: 95% @40°C (Non-condensing)
Operating Temperature: 0 ~ 55°C(32 ~ 131°F) @ 5 ~ 85% RH with 0.7m/s
airflow (Industry SSD)
Storage Temperature: - 40 ~ 85°C (-104 ~ 185°F)
Shock Protection:
–IEC 60068-2-27
–mSATA: 20 G @ wall mount, half sine, 11 ms
Vibration Protection:
–IEC 60068-2-64 (Random 1 Oct./min, 1hr/axis.)
–mSATA: 2 Grms @ 5 ~ 500 Hz
1.3.3 Expansion Board (Optional)
Model: UNO-3384G
Optional Expansion Type:
1x PCIe slot, 1 x PCIex4 slot; 1x PCI slot, 1 x PCI slot;
1.4 Safety Precautions
The following sections tell how to make each connection. In most cases, you will sim-
ply need to connect a standard cable.
Warning! Always disconnect the power cord from your chassis whenever you are
working on it. Do not connect while the power is on. A sudden rush of
power can damage sensitive electronic components. Only experienced
electronics personnel should open the chassis.
Caution! Always ground yourself to remove any static electric charge before
touching UNO-3000G series. Modern electronic devices are very sensi-
tive to static electric charges. Use a grounding wrist strap at all times.
Place all electronic components on a static-dissipative surface or in a
static-shielded bag.

5 UNO-3300G Series User Manual
Chapter 1 Overview
1.5 Chassis Dimensions
Figure 1.1 UNO-3382G Dimensions
Figure 1.2 UNO-3384G Dimensions
1.6 Accessories
Refer to the below accessories list for UNO-3300G series.
1
1
× 3-pin plug-in block for power wiring
× Warranty card
254
207
26
26
195 199
10
194 198
254
207
67
67
199 195
194 198
10

UNO-3300G Series User Manual 6

Chapter 2
2Hardware
Functionality
This chapter shows how to setup
UNO-3300G series' hardware
functions, including connecting
peripherals, setting switches and
indicators.
Sections include:
Peripherals
RS-232 Interface
RS-422/485 Interface
LAN / Ethernet Connector
Power Connector
Mini PCIe Socket
Audio Connector
USB Connector
DP/HDMI Display Connector

UNO-3300G Series User Manual 8
2.1 Introduction
The following figures show the interfaces of UNO-3300 series and the detail informa-
tion by each peripheral.
Figure 2.1 UNO-3382G Dimensions
Figure 2.2 UNO-3384G Dimensions
254
207
26
26
195 199
10
194 198
254
207
67
67
199 195
194 198
10

9 UNO-3300G Series User Manual
Chapter 2 Hardware Functionality
Figure 2.3 UNO-3382G Bottom View
Figure 2.4 UNO-3382G Front View
Figure 2.5 UNO-3384G Bottom View
Figure 2.6 UNO-3384G Front View

UNO-3300G Series User Manual 10
2.2 Serial Interface (Iso.COM)
The UNO-3300G series offer one standard RS-232/422/485 serial communication
interface ports: COM (Pin header CN35).
The IRQ and I/O address of serial ports are listed as below.
COM: 2E8, IRQ4
Figure 2.7 Pin header of COM1
2.2.1 RS-232/422/485 Interface (COM)
The UNO-3300 series offers one serial communication interface port (COM), COM
allows,
SW1 for RS-232/422/485 switch
SW2 for RS485/422 receiver termination setting
In RS-422/485 mode, the UNO-3300 series automatically detects signals to match
RS-422 or RS-485 networks.
In RS-485 mode, the UNO-3300 series automatically detects the direction of incom-
ing data and switches its transmission direction accordingly. So no handshaking sig-
nal (e.g. RTS signal) is necessary. This lets you conveniently build an RS-485
network with just two wires. More importantly, application software previously written
for half duplex RS-232 environments can be maintained without modification.