Advantech WISE-1530 User manual

User Manual
WISE-1530
M2.COM WIFI/BLE IoT Node
OEM/Integrators Installation
Manual

WISE-1530 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
ARM is trademarks of ARM Corporation.
Freescale is trademarks of Freescale Corporation.
Microsoft Windows are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech's high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive,
it will be repaired or replaced at no charge during the warranty period. For out-of-
warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
Part No. 2006E15300 Edition 1
Printed in China March 2019

iii WISE-1530 User Manual
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
FOR PORTABLE DEVICE USAGE (<20m from body/SAR needed)
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncon-
trolled environment and are safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept as far
as possible from the user body or set the device to lower output power if such func-
tion is available.
FOR MOBILE DEVICE USAGE (>20cm/low power)
Radiation Exposure Statement:
Caution! Any changes or modifications not expressly approved by the party
responsible for compliancecould void the user's authority to operate this
equipment.

WISE-1530 User Manual iv
This equipment complies with FCC radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES)
Note: The country code selection is for non-US model only and is not available to all
US model. Per FCC regulation, all WiFi product marketed in US must fixed to US
operation channels only.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and oper-
ated. The end user has to be informed that the FCC radio-frequency exposure guide-
lines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate
this equipment.
If the labelling area is small than the palm of the hand, then additional FCC part 15.19
statement is required to be available in the users manual: This device complies with
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains
TX FCC ID: M82-WISE1530 ".
If the labelling area is larger than the palm of the hand, then the following FCC part
15.19 statement has to also be available on the label: This device complies with Part
15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NCC
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者
均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指
依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學
及醫療用電波輻射性電機設備之干擾。
模組認證：
1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。
2. 系統廠商應於平台上標示 「本產品內含射頻模組： 字樣。

v WISE-1530 User Manual
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
1 WISE-1530
1 Screw for WISE-1530
1 China RoHs Notice
Optional Accessories
Development Board
Ordering Information
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
Part No. Description
1750008001-01 Wi-Fi antenna Dipole L=141.5mm, 5dBi 2.4/5GHz
1750008653-01
1750007965-01 Antenna Cable RP-SMA to MHF4 L=200mm Antenna Cable R/P SMA (M) to MHF4, 300mm
1700015038 FPC Cable 10P-0.5mm 7.9cm for DCU2.0
1931000590 Screw M2.5x5L F/S D=5.3 H=0.8 (1+) ST Ni
1700023619-01 A cable USB-A 4P(M)/micro USB 5P(M) 1m ADAM-T212
1700025876-01 M cable USB-A 4P(M)/Plug-in 2P-5.0 90CM
XRISC-ADP-10HW-AG ADP A/D 100-240V 10W 5V WM
193A231540 POST F=M3*6L M=M3*6L D=5 d=2.88 B=5 H=15 Cu
Part No. Description
9696150000E ASS'Y WISE-DB1500 A101-1 M2.COM CARRIER
9696ED2200E ASS’Y WISE-ED22 A101 Daughter Board
Part No. WISE-1530ITB-SDA10
WISE-1530 M2.COM WIFI/BLE module

WISE-1530 User Manual vi
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the
user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

vii WISE-1530 User Manual
Contents
Chapter 1 Product Overview................................1
1.1 Introduction ...............................................................................................2
1.2 Specifications............................................................................................3
Chapter 2 H/W Installation....................................5
2.1 Board Connector.......................................................................................6
Figure 2.1 Card Edge Bevel ........................................................6
Figure 2.2 Card Edge Outline-Topside........................................6
Figure 2.3 Card Edge Outline-Backside......................................7
2.2 Module Outline..........................................................................................8
Figure 2.4 Type A 2230...............................................................8
2.3 Connector Specifications ..........................................................................8
2.3.1 Top Side Connector Physical Dimensions....................................8
Figure 2.5 Top Side Connector Physical Dimensions .................9
2.3.2 Carrier Board Connection Length.................................................9
Figure 2.6 Carrier Board Connection Length.............................10
2.3.3 Carrier Board Connector Height .................................................10
Figure 2.7 H3.2-D3....................................................................10
2.4 WISE-1530 Pin-Out Map.........................................................................11
Figure 2.8 M.2 Connector..........................................................12
2.5 Quick Starter of WISE-1530....................................................................12
2.5.1 Preparing for Hardware...............................................................12
Chapter 3 Development Environment Setup....15
3.1 Overview.................................................................................................16
3.2 Installation of WICED Studio...................................................................17
3.2.1 Windows Install...........................................................................17
3.2.2 Copy patch file............................................................................19
3.3 Build Source File.....................................................................................20
3.3.1 Make a "Make Target" file...........................................................20
3.3.2 Build Project................................................................................21
3.4 Generate a Programming File.................................................................23
3.4.1 Launch J-Flash ...........................................................................24
3.4.2 Open bootloader bin file..............................................................24
3.4.3 Merge DCT bin file......................................................................25
3.4.4 Merge application bin file............................................................25
3.4.5 Save as a final bin file.................................................................26
3.5 Programming...........................................................................................26
3.5.1 Debug Setting.............................................................................26
Chapter 4 Example: WISE-1530 Demo(StartKit)...
29
4.1 Introduction .............................................................................................30
4.2 Detailed about WISE-1530 Demo...........................................................30
4.3 Step by step usage guide........................................................................31
4.4 memory/flash usage................................................................................36
4.5 I/O Test (factory).....................................................................................37
4.5.1 Introduction.................................................................................37

WISE-1530 User Manual viii
4.5.2 I/O Test Use WICED API............................................................ 37
4.5.3 I/O Test Use SUSI API ............................................................... 39

Chapter 1
1Product Overview

WISE-1530 User Manual 2
1.1 Introduction
WISE-1530 is a wireless module integrated with ARM Cortex-M4 Processor and Wifi
/ BLE connectivity. This technology is the best solution for WIFI and BLE combo
Applications. For example, we may use BLE to configure device and transfer mass
data through wifi connectivity. You may choose the WIFI or BLE to submit your sen-
sor data according to different scenario and purpose, such as the short range with
low power consumption or mass data rate to complete the specific task.
Your sensors or applications with low data rate requirement can be achieved years
battery lifetime in short range communication BLE. Advantech WISE-1530 also pro-
vides multi-interfaces for sensor and I/O control.
With ThreadX v5.6 microprocessor operating system and add-on software stacks, it's
convenient to build the application software or sensor algorithm over the OS. Data
can be quickly and easily acquired and transformed into a different format to commu-
nicate with WISE-PaaS or other cloud services. Developer can build their application
backbone faster and focus on their applications, value-added services.
The main features of WISE-1530 are:
ARM Cortex-M4 Core Processor
Built-in Wifi / BLE connectivity
Great for Low Power Energy application
Rich interfaces for sensor and I/O control
Support ThreadX v5.6
Support wide temperature -20 ~ 70 °C

3 WISE-1530 User Manual
Chapter 1 Product Overview
1.2 Specifications
* Note: Frequency Band can be configurable for Japan or Korea by request.
Processor System MCU STM32F4 ARM® 32-bit Cortex®-M4 CPU 100MHz
Memory RAM 256KB
Flash 1024KB
Form Factor M2.COM Type A 2230
Spec. Standard M2 COM Technical SPEC_v1.1
Wireless Network
Standard IEEE 802.11b/g/n and Bluetooth 4.1
Frequency
Band 2.4000~2.4840 GHz for Wi-Fi 2.4000~2.4835 GHz for BLE
Channels 1~13 for Wi-Fi and 79 for Bluetooth and 39 for BLE
Topology Star network
Transmit
Power
Typ. 14 dBm ± 2 at 802.11b CCK Mode 1M
Typ. 12 dBm ± 2 at 802.11g OFDM Mode 54M
Typ. 12 dBm ± 2 at 802.11n OFDM Mode MCS0
Max 10 dBm ± 2 for BLE
Receiver
Sensitivity
Typ. -95dBm at 1 Mbps
Typ. -75 dBm at 54 Mbps
Typ. -89 dBm at MCS0
Typ. -89 dBm for BLE
RF Data
Rate Up to 65Mbps
Function End node
Antenna
connector MHF4 connector
I/O
UART 1 (2 wire support RTS/CTS)
I2C 1
GPIO 2
SPI 1
I2S 1
ADC 4
Programming / Debug
Port 1 via WISE-ED22 (CN1)
Power 3.3V
Environment
Operational
Temperature -20 ~ 70° C
Operating
Humidity 5% ~ 95% Relative Humidity, non-condensing
Physical
Characteristics Dimensions (WxD) 22 x 30 mm
OS ThreadX v5.6, SDK 4.1.8

WISE-1530 User Manual 4

Chapter 2
2H/W Installation

WISE-1530 User Manual 6
2.1 Board Connector
M2.COM Type A Module
Module size: 22 mm x 30 mm
PCB thickness: 0.8 mm ± 10%
Pin count: 75 pins
Module input voltage: 3.3V DC-in
Connector mating force: 30N Maximum
Connector current rating: 0.5A / Power contact
Connector operation temperature range: -45 °C to +85 °C
Figure 2.1 Card Edge Bevel
Figure 2.2 Card Edge Outline-Topside

7 WISE-1530 User Manual
Chapter 2 H/W Installation
Figure 2.3 Card Edge Outline-Backside
Reference from PCI Express M.2 Specification Rev 1.0 (Nov 1, 2013) Section 2.3.5
Card PCB Details

WISE-1530 User Manual 8
2.2 Module Outline
The mechanical dimension information of M2.COM form factor follows the Type A
2230 module size: 22 x 30 mm. Both module types use a 75-position host interface
connector and have room to support up to four RF connectors in the upper section.
Figure 2.4 Type A 2230
2.3 Connector Specifications
2.3.1 Top Side Connector Physical Dimensions
The top-side scheme has two connectors that share a common footprint but have dif-
ferent stack-up requirements.
Length - 22 mm maximum including land pattern
Width - 9.1 mm maximum including land pattern

9 WISE-1530 User Manual
Chapter 2 H/W Installation
Figure 2.5 Top Side Connector Physical Dimensions
Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013
2.3.2 Carrier Board Connection Length
The carrier board connector of M2.COM follows the p Type 2230 M.2 module con-
nector:
The additional increase in length is 7.05mm maximum for top-side connector to
the module length.
The retention screw adds 2.75 mm maximum.
The maximum extension, including land pattern, beyond the module leading
edge is 4.3 mm.
M2.COM module lengths are 30 mm and 42 mm.

WISE-1530 User Manual 10
Figure 2.6 Carrier Board Connection Length
Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013
2.3.3 Carrier Board Connector Height
The dimensions of M2.COM form factor follow the Type A 2230 -D3 M.2 module size.
Hence, the carrier board connectors must choose H3.2-D3 or H4.2-D5 connector as
in the following diagrams.
Figure 2.7 H3.2-D3
Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013

11 WISE-1530 User Manual
Chapter 2 H/W Installation
2.4 WISE-1530 Pin-Out Map
PIN M2.COM
Signal name STM32L443RCI6 MCU Pin Name M2.COM Signal name PIN
1 GND GND 3.3V VCC 2
3 MICRO_USB_HS_DP PA12 3.3V VCC 4
5MICRO_USB_HS_D
NPA11 NC 6
7 GND GND PB12 I2S_CK_MICRO 8
9 NC PA4 I2S_WS_MICRO 10
11 NC PC12 I2S_SD_MICRO 12
13 NC NC 14
15 NC PB14 CB_RESET_OUT# 16
17 NC GND GND 18
19 NC PC9 CB_PWR_ON 20
21 NC PA9 UART3_TX (O)(0/3.3V) 22
23 NC Connector Key
Connector Key Connector Key
Connector Key Connector Key
Connector Key Connector Key
Connector Key PA10 UART3_RX (I)(0/3.3V) 32
33 GND GND NC 34
35 NC NC 36
37 NC PA5 GPIO_0_MICRO 38
39 GND GND PB0 GPIO_1_MICRO 40
41 NC NC 42
43 NC PB13 GPIO_3_WL 44
45 GND GND PB0 GPIO_4_WL 46
47 ADC0_MICRO PA6 PB2 GPIO_5_WL 48
49 ADC1_MICRO PA7 PB1 GPIO_6_WL 50
51 GND GND NC 52
53 ADC2_MICRO PC4 NC 54
55 ADC3_MICRO PC5 NC 56
57 GND GND PB7 I2C0_SDA 58
59 NC PB6 I2C0_SCL 60
61 NC PC3 SPI_MOSI 62
63 GND GND PC2 SPI_MISO 64
65 +VBAT_R VBAT(3.3V) PB13 SPI_SCK 66
67 NC PB9 SPI_CS0# 68
69 GND GND NC 70
71 RESET_IN# NRST 3.3V VCC 72
73 WAKEUP_MICRO# PC0 3.3V VCC 74
75 GND GND

WISE-1530 User Manual 12
Figure 2.8 M.2 Connector
2.5 Quick Starter of WISE-1530
2.5.1 Preparing for Hardware
The user needs to prepare for hardware as following:
WISE-1530, WISE-1500 and WISE-ED22.
802.11b/g/n (2.4 GHz) Wireless Access Point (AP).
PC Runs on Windows®, Mac® OS X®, and Linux®
Please refer to the following steps for setup a WISE series of boards before using
WISE-1530.
Step 01: Please prepare boards as below.
1.WISE-1530
2.WISE-1500
3.WISE-ED22
4.WISE-ED22 reset button
5.CN2 on WISE-1500