AFRISO ARV ProClick User manual

NOTICE!
This instruction manual is also available on www.afriso.pl.
WARNING!
The product may only be mounted, commissioned and disposed of by qualied, specially trained
staff.
Alterations performed by unauthorized staff may cause a threat and are forbidden for safety
reasons.
APPLICATION
DESCRIPTION
APPROVALS AND CERTIFICATES
Drawing 1. Construction
4-way rotary mixing valves are commonly used with solid fuel boilers, as mixing valves which simultaneously increase
the temperature of the water returning to the boiler. They can be also successfully utilized in systems with cast iron
gas or oil boilers.
4-way rotary mixing valves ARV ProClick with inner threads are made of brass. The connections have octagonal shape.
The valves have knobs for manual operation and rotation angle limiters. The scale on top of the knob is printed on one
side with “from 0 to 10” and on the other “from 10 to 0”, so one can mount the valve in various positions. The thicker
knob part shows the sleeve position inside the valve. The knob itself is made from a non-slip material. The durable
plastic parts under the knob are used to mount the ARM ProClick actuator on the valve. The ProClick system does not
require any tools. ARV ProClick valves require low torque.
The rotary mixing valves ARV ProClick comply with the Pressure Directive PED 2014/68/EU and according to article 4.3
(sound engineering practice) must not wear the CE mark.
DN20 ÷ DN25
DN32DN40 ÷ DN50
4-way rotary mixing valves
ARV ProClick
Art.-No 13 482 10, 13 484 10, 13 485 10,
13 486 10, 13 487 10
INSTRUCTION MANUAL 953.001.0064 1
TECHNICAL DATA
Parameter / piece Value / description
Working temperature 5-110˚C
Working pressure max 10 bar
Differential pressure max 1 bar
Body brass CW617N
Sealing EPDM
Leak rate (Δp=50 kPa) max 1,5%
Rotation angle 90˚
Required torque max 1 Nm
Glycol concentration max 50%
MOUNTING
Notice! The attening on the spindle of the valve and on the adapter mounted on it (Drawing 1) indicates the middle
of the obturator inside the valve (Drawing 2a and 2b).
The ARV ProClick valve is delivered with mounted knob, blue ring and scale. Not to damage the plastic elements,
we suggest to disassemble the scale, knob and blue limiting ring before mounting the valve. These parts are moun-
ted on latch. When having trouble with dismounting the knob, one can gently pry it up with a at screwdriver.
Next mount the valve in the system. When the valve is in place, set it and assemble the plastic components,
as follows:
1. Determine the working range of the obturator inside the valve and the closing direction (Drawing 2).
First determine the hot water inlet from the boiler, system outlet, system return and boiler return. Next set
the obturator exactly in the middle of the system outlet and boiler return (Drawing 2 - “s” axis). This means
the valve is open in 50%. The obturator must work in the range of +/- 45˚ from that position.
2. Determine the closing direction of the valve and choose the right side of the scale. A 4-way valve is closed when
the hot water from the boiler is owing completely to the return of the boiler (Drawing 2a and 2b – “z” axis).
The indicator coincides with position “0” on the scale. Depending on the exact system, closing the valve can
mean turning the obturator left (Drawing 2a) or right (Drawing 2b). A 4-way valve is open when the hot water
from the boiler is supplying the system outlet (Drawing 2a and 2b – “o” axis). The indicator coincides then with
position “10” on the scale. Depending on the exact system, opening the valve can mean turning the obturator
right (Drawing 2a) or left (Drawing 2b). A double-sided scale is delivered with the ProClick valves. It is printed
“from 0 to 10” on one side and “from 10 to 0” on the other. Choose the correct side following the rule:
- if the valve is closed turned right (clockwise) choose the scale “from 0 to 10”,
- if the valve is closed turned left (counter-clockwise) choose the scale “from 10 to 0”.
3. Put on and latch the blue limiting ring on the valve, which was set according to point 1. The indicator should
point directly on the middle of the attening on the spindle and adapter (Drawing 3).
4. Lock the knob on the adapter. It ts only in one position (Drawing 4).
5. Put the lid with the chosen scale (Drawing 5) on the knob. To lock the lid rst put the smaller inset in the hole
inside the knob and then press the lid down.
6. Check if the valve works properly.
valve body DN40-DN50
valve body DN32
valve body DN20-DN25 with plastic part for ProClick actuator
adapter with attening, for ARM ProClick actuators
adapter xing screw
knob with a thicker part showing the valve sleeve position
double-sided scale
limiting ring with indicator
attening on the valve spindle
AFRISO Sp. z o.o.
Szałsza ul. Kościelna 7
42-677 Czekanów
Poland
www.afriso.pl
Customer service
Tel. [phone]
Fax: [phone]
[email protected]
1 2

EXAMPLE APPLICATIONSDrawing 2a. Choosing the scale Drawing 2b. Choosing the scale
Drawing 3. Mounting the blue ring Drawing 4. Mounting the knob Drawing 5. Mounting the scale
USING THE VALVE Drawing 6. ProClick system
1. Position of the knob with scale
After the valve was properly mounted and set, position
“0” will mean the valve is totally closed (hot water clo-
sed) and position “10” – the valve is fully open
(hot water open). Every other positon means a percenta-
ge opening (e.g. “4” means valve open in 40%).
2. Position of the sleeve inside the valve
The middle of the thicker raised part of the knob
indicates the position of the obturator inside the valve.
It makes checking the work of the valve easier after
mounting.
3. Mounting the electric actuator ARM ProClick
Under the knob of the valve there is always an adapter
for ARM ProClick electric actuators. Thanks to the
ProClick system (Drawing 6) one needs only to take off
the knob and blue limiting ring and slide the actuator
onto the valve. The mechanism will lock itself on the
valve.
1. Dismount the device.
2. To protect the environment, this product must not be disposed of together with regular household waste. Dispose
of the product according to local directives and guidelines. This device consists of materials that can be reused by recyc-
ling companies.
The manufacturer’s warranty for this product is 36 months after the date of sale from AFRISO sp. z o.o.. In case of any alteration
in the product or usage against this instruction manual, the warranty becomes void.
For AFRISO sp. z o.o. customer satisfaction is the prime objective. Please contact us if you have any questions, suggestions
or problems concerning our product: [e-mail], [phone].
The ARV ProClick valve is a maintenance-free product.
DISMOUNTING, DISPOSAL
MAINTENANCE
WARRANTY
CUSTOMER SATISFACTION
Z
SS
O O Z
indicator in the
middle of the outlets

on the adapter
More applications can be found on www.afriso.pl or in the Technical brochure.
3 4