Agilent Technologies 3070 Series Operating instructions

Agilent 3070 / 79000 Board Test
Systems
Site Preparation
June 2002

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 1
Site Preparation – Legal Notices
03066-90114 Rev. Z 06/2002
In this Chapter ■Notice, 1
■U.S. Government Restricted Rights, 1
■Radiated Immunity, 2
■Overvoltage Category, 2
■Pollution Degree for Agilent 3070 / 79000 Systems, 2
■Insulation Rating for Wires Connected to Agilent 3070
/ 79000 Systems, 2
■Acoustic Level for Agilent 3070 / 79000 Systems, 2
■Acknowledgements, 2
■3070 Series I DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014, 3
■3070 Series II DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014, 4
■3070 Series 3 DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014, 5
■79000 / xDSL DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014, 6
■Emergency Shutdown, 7
■Warranty, 8
■User Safety Symbols, 9
■Safety Symbols, 10
■Warnings, 11
Notice
This manual is provided “as is” and is subject to change
without notice.
AGILENT TECHNOLOGIES, INC. MAKES NO
WARRANTY OF ANY KIND WITH REGARD TO
THIS MATERIAL, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
NONINFRINGEMENT, MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Agilent
shall not be liable for errors contained herein, nor for
direct, indirect, general, special, incidental or
consequential damages in connection with the
furnishing, performance, or use of this material.
U.S. Government Restricted Rights
The Software and Documentation have been developed
entirely at private expense. They are delivered and
licensed as “commercial computer software” as defined
in DFARS 252.227-7013 (Oct 1988), DFARS
252.211-7015 (May 1991) or DFARS 252.227-7014
(Jun 1995), as a “commercial item” as defined in FAR
2.101(a), or as “Restricted computer software” as
defined in FAR 52.227-19 (Jun 1987) (or any equivalent
agency regulation or contract clause), whichever is
applicable. You have only those rights provided for such
Software and Documentation by the applicable FAR or
DFARS clause or the Agilent standard software
agreement for the product involved.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 2
:
Radiated Immunity
When subjected to high RFI fields (greater than 1 V/m),
reduced performance may be experienced when making
low-level analog measurements.
Overvoltage Category
AC Power Overvoltage Category: CAT III
Pollution Degree for Agilent 3070 / 79000
Systems
Pollution Degree 2
Insulation Rating for Wires Connected to Agilent
3070 / 79000 Systems
Use only external wiring with insulation rated for the
maximum voltage (Vrms, Vpk or Vdc) and temperature
to which the wire may be subjected in a fault condition.
Example: The system is connected to a source whose
output is set for 50 Vrms. The source could be set for as
high as 300 Vrms, intentionally or unintentionally.
Therefore, the external wiring connected between this
source and the system must be rated for 300 Vrms.
Acoustic Level for Agilent 3070 / 79000 Systems
LpA = 69dB
am Arbeitsplatz (operator’s position)
normaler Betrieb nach EN27779: 1991
Acknowledgements
The XWD i/o and GIF output routines are derived from
Jef Poskanzer’s PBMplus package:
© Copyright by Jef Poskanzer 1989
HP is a registered trademark of Hewlett-Packard
Company.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 3
:
3070 Series I DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: Agilent Technologies, Inc.
Manufacturing Test Division
Manufacturer’s Address: 815 14th Street S.W.
Loveland, Colorado 80537
Declares that the Product Name: 3070 (Series I) Board Test Systems
Model Numbers: 3070
Product Options: All
Conforms to the following Product Specifications:
Safety: IEC 348:1978/HD 401 S1:1981
CSA 556B
UL 1244
Safety qualification performed August 1987
EMC: CISPR 11:1990/EN55011 (1991): Group 1, Class A
IEC 801-2:1991/EN50082-1 (1992): 4kV CD, 8kV AD
IEC 801-3:1984/EN50082-1 (1992): 3V/m
IEC 801-4:1988/EN50082-1 (1992): 1kV Power Line, 0.5kV Signal Lines
Attestation is provided according to article 10 (2) of the Directive by a Technical Contruction File.
Technical File Number: 97-0900-010-TCF Rev: A Dated: 25 February, 1997
Supplementary Information: This product also herewith complies with the requirements of the Low Voltage Directive 72/23/EEC and the
protection requirements of the EMC Directive 89/336/EEC (inclusive 93/68/EEC) and carries the "CE" mark accordingly.
A Technical Report/Certificate was issued in accordance with Part V (Reg 50) of the UK Regulations (SI 1992 No. 2372) by a UK-appointed
Competent Body, namely,
Design to Distribution Limited
Westfields House, West Avenue
Kidsgrove, Stoke-on-Trent
Staffordshire, ST7 1TL United Kingdom
Certificate Number: D2D/EMC/CC/007/97 Dated: 10 March, 1997
March 25, 1997
For further information contact your local Agilent Sales and Service office.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 4
:
3070 Series II DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: Agilent Technologies, Inc.
Manufacturing Test Division
Manufacturer’s Address: 815 14th Street S.W.
Loveland, Colorado 80537
Declares that the Product Name: 3070 Series II Board Test Systems
Model Numbers: 3070, 72, 73, 75, 79 and 3170, 72, 73, 75, 79 and 3272, 73, 75, 79
Product Options: All
Conforms to the following Product Specifications:
Safety: IEC 1010-1 (1990) Incl. Amend 1 (1992)/EN61010-1 (1993)
CSA C22.2 #1010.1 (1992)
UL 1244
EMC: CISPR 11:1990/EN55011 (1991): Group 1, Class A
IEC 801-2:1991/EN50082-1 (1992): 4kV CD, 8kV AD
IEC 801-3:1984/EN50082-1 (1992): 3V/m
IEC 801-4:1988/EN50082-1 (1992): 1kV Power Line, 0.5kV Signal Lines
Attestation is provided according to article 10 (2) of the Directive by a Technical Contruction File.
Technical File Number: 95-0900-001-TCF Rev: A Dated: 31 March, 1995
Supplementary Information: This product also herewith complies with the requirements of the Low Voltage Directive 72/23/EEC and the EMC
Directive 89/336/EEC (inclusive 93/68/EEC) and carries the "CE" mark accordingly.
A Technical Report/Certificate has been issued in accordance with Part V (Reg 50) of the UK Regulations (SI 1992 No. 2372) by a UK-appointed
Competent Body, namely,
Interference Technology International Limited
41-42 Shrivenham Hundred Business Park
Shrivenham, Swindon, Wilts. SN6 8TZ
England, UK
Certificate Number: ITI/0084/UK Dated: 11 April, 1995
April 20, 1995
For further information contact your local Agilent Sales and Service office.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 5
:
3070 Series 3 DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: Agilent Technologies, Inc.
Manufacturing Test Division
Manufacturer’s Address: 815 14th Street S.W.
Loveland, Colorado 80537
Declares that the Product Name: 3070 Series 3 Board Test Systems
Model Numbers: 3070, 2, 3, 5, 9 and 3170, 2
Product Options: All
Conforms to the following Product Specifications:
Safety: IEC 1010-1 (1990) Incl. Amend 1 (1992) + Amend 2 (1995)/EN61010-1 (1993) + A2 (1995)
CSA C22.2 #1010.1 (1992)
UL 3111
EMC: CISPR 11:1990/EN55011 (1991): Group 1, Class A
EN50082-1:1992
IEC 1000-4-2:1995: 4kV CD, 8kV AD
IEC 1000-4-3:1995: 3V/m
IEC 1000-4-4:1995: 1kV Power Line, 0.5kV Signal Lines
Attestation is provided according to article 10 (2) of the Directive by a Technical Contruction File.
Technical File Number: 97-0900-030-TCF Rev: A Dated: 12 February, 1998
Supplementary Information: This product also herewith complies with the requirements of the Low Voltage Directive 72/23/EEC (inclusive 93/68/EEC), and
with therequirements of the Machinery Directive 89/392/EEC (inclusive 93/68/EEC), and with the protection requirements of theEMC Directive 89/336/EEC and
carries the "CE" mark accordingly. (Note: Compliance with the Machinery Directive requires equipment installation to be performed in accordance with the
Agilent Application Note, "Compliance with the Machinery Directive requires specific installation procedure.") A Technical Report/Certificate has been issued in
accordance with Part V (Reg 50) of the UK Regulations (SI 1992 No. 2372) by a UK-appointed Competent Body, namely,
Celestica Limited
Westfields House, West Avenue
Kidsgrove, Stoke-on-Trent
Staffordshire, ST7 1TL United Kingdom
Certificate Number: TCR/98/023 Dated: 20 March, 1998
May 1, 1998
For further information contact your local Agilent Sales and Service office.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 6
:
79000 / xDSL DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: Agilent Technologies, Inc.
Manufacturing Test Division
Manufacturer’s Address: 815 14th Street S.W.
Loveland, Colorado 80537
Declares that the Product Name: 79000 Series Functional Test Systems
Model Numbers: E2195A, E2196A, E2190A
Product Options: All
Conforms to the following Product Specifications:
Safety: IEC 61010-1 (1990) + A2:1995/EN61010-1:1993 + A2:1995
CSA C22.2 #1010.1:1992
UL 3111-1
EMC: CISPR 11:1990/EN55011 (1991): Group 1, Class A
EN50082-1:1992
IEC 61000-4-2:1995/: 4kV CD
IEC 61000-4-3:1995/: 3V/m
IEC 61000-4-4:1995/: 1kV Power Line
Attestation is provided according to article 10 (2) of the Directive by a Technical Contruction File.
Technical File Number: 99-0900-001-TCF Rev: A Dated: 5 February, 1999
Supplementary Information: This product also herewith complies with the requirements of the Low Voltage Directive 72/23/EEC (inclusive
93/68/EEC), and with the requirements of the Machinery Directive 89/392/EEC (inclusive 93/68/EEC), and with the protection requirements of the
EMC Directive 89/336/EEC and carries the "CE" mark accordingly. A Technical Report/Certificate was issued in accordance with Part V (Reg 50)
of the UK Regulations (SI 1992 No. 2372) by a UK-appointed Competent Body, namely,
Celestica Limited
Westfields House, West Avenue
Kidsgrove, Stoke-on-Trent
Staffordshire, ST7 1TL United Kingdom
Certificate Number: CC/KID/009/99 Dated: 22 February, 1999
February 26, 1999
For further information contact your local Agilent Sales and Service office.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 7
:
Emergency Shutdown
The Emergency Shutdown Switch, (or Emergency Off,
EMO) is the large red button located at the lower left
corner on the front of the testhead. It turns off all ac and
dc power to the testhead, and is equivalent to turning off
the PDU on the rear of the pod. Press the Emergency
Shutdown Switch if you need to power down the
testhead and its associated equipment in an emergency.
DO NOT use the Emergency Shutdown Switch as a
substitute for correct power-down (unboot) procedures
i.e., executing the testhead power off command.
To restore power after pressing the Emergency
Shutdown Switch, switch the PDU Off for 15 seconds
and then On again.
Emergency Shutdown
Switch (EMO)

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 8
:
Warranty
Agilent 3070 / 79000 BOARD TEST SYSTEMS 1-YEAR
1. Agilent warrants Agilent hardware, accessories and
supplies against defects inmaterials and workmanship for the
period of one year. If Agilent receives notice of such defects
during the warranty period, Agilent will, at its option, either
repair or replace products which prove to be defective.
Replacement products may be either new or like-new.
2. Agilent warrants that Agilent software will not fail to
execute its programming instructions, for the period of one
year, due to defects in material or workmanship when
properly installed and used. If Agilent receives notice of
defects during the warranty period, Agilent will replace
software media which does not execute its programming
instructions due to such defects.
3. Agilent does not warrant that the operation of Agilent
products will be uninterrupted or error free. If Agilent is
unable, within a reasonable time, to repair or replace any
product to a condition as warranted, customer will be entitled
to a refund of the purchase price upon prompt return of the
product to Agilent.
4. Agilent products may contain remanufactured parts
equivalent to new in performance or may have been subject
to incidental use.
5. The warranty period begins on the date of delivery or on
the date of installation if installed by Agilent. If customer
schedules or delays Agilent installation more than 30 days
after delivery, warranty begins on the 31st day from delivery.
6. Warranty does not apply to defects resulting from (a)
improper or inadequate maintenance or calibration, (b)
software, interfacing, parts or supplies not supplied by
Agilent, (c) unauthorized modification or misuse, (d)
operation outside the published environmental specifications
for the product, or (e) improper site preparation or
maintenance.
7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE
ABOVE WARRANTIES ARE EXCLUSIVE AND NO
OTHER WARRANTY OR CONDITION, WHETHER
WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED AND
AGILENT SPECIFICALLY DISCLAIMS ANY IMPLIED
WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND
FITNESS FOR A PARTICULAR PURPOSE.
8. Agilent will be liable for damage to tangible property per
incident up to the greater of $300,000 or the actual amount
paid for the product that is the subject of the claim, and for
damages for bodily injury or death, to the extent that all such
damages are determined by a court of competent jurisdiction
to have been directly caused by a defective Agilent Product.
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE
REMEDIES IN THIS WARRANTY STATEMENT ARE
CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES.
EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL
AGILENT OR ITS SUPPLIERS BE LIABLE FOR LOSS
OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL (INCLUDING LOST PROFIT OR
DATA), OR OTHER DAMAGE WHETHER BASED IN
CONTRACT, TORT, OR OTHERWISE.
FOR CONSUMER TRANSACTIONS IN AUSTRALIA
AND NEW ZEALAND: THE WARRANTY TERMS
CONTAINED IN THIS STATEMENT, EXCEPT TO THE
EXTENT LAWFULLY PERMITTED, DO NOT
EXCLUDE, RESTRICT OR MODIFY AND ARE IN
ADDITION TO THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE SALE OF THIS
PRODUCT TO YOU.

©Agilent Technologies 1989–2002 Agilent 3070 / 79000 Site Preparation 9
:
User Safety Symbols
These symbols are used on labels on various places on
the testhead.
WARNING — Do not operate the testhead if you can see this
symbol. It means that hazards exist because the safety shroud
is not installed. These hazards include pinched fingers from
pulling down a test fixture and electrical shock if Agilent
Performance Port is installed.
WARNING — Keep your hands away from the indicated
areas of the testhead to avoid pinched fingers when rotating the
testhead.
WARNING — Do not rotate the testhead past 65 degrees with
a fixture installed, or the fixture could fall off the testhead,
causing personal injury.
CAUTION - ESD — Devices sensitive to electrostatic
discharge may be present. Follow approved ESD-safe handling
practices while working with this equipment.
!
!
55 -
50 -
65 -