AJAX MotionCam Fibra User manual

MotionCam (PhOD) Fibra User manual
Updated July 12, 2023
MotionCam (PhOD) Fibra is a wired motion detector featuring photo verication
of alarms, Photo on Demand, and Photo by Scenario. The device is designed for
indoor use only. Detects movement at a distance of up to 12 meters. Ignores
pets when installed and congured correctly.
An Ajax hub is required for the detector to operate. MotionCam (PhOD) Fibra is
compatible with and on or higher.
Connection to other , , , and is
not provided.
MotionCam (PhOD) Fibra is part of an Ajax system and exchanges data with the
hub using the secure Fibra wired communication protocol. Wired
communication can be up to 2,000 meters long when connected using the
U/UTP cat.5 twisted pair cable.
MotionCam (PhOD) Fibra relates to the Fibra product line of wired devices. Only
accredited Ajax Systems partners can buy, install, and administer Fibra
Hub Hybrid (2G) Hub Hybrid (4G) OS Malevich 2.15.2
hubs radio signal range extenders ocBridge Plus uartBridge

products.
Functional elements
Buy MotionCam (PhOD) Fibra
1. LED indicator.
2. Motion detector lens.
3. Infrared (IR) backlight. Used to take photos in dark and low-light conditions.
4. Camera.
5. SmartBracket mounting panel. To remove the panel, slide it down.
6. Perforated parts of the mounting panel. Necessary to trigger a tamper in
case of any attempt to detach the detector from the surface. Do not break
them off!
7. The hole for attaching the SmartBracket mounting panel with a screw.

Operating principle
MotionCam (PhOD) Fibra is a wired motion detector supporting photo
verication. After detecting motion, it takes a series of images, which allows you
to assess what is happening at the facility in dynamics. This relieves users of
unnecessary anxiety and security companies of unnecessary patrol despatches.
When an armed detector identies motion, it instantly sends an alarm to the
hub. Control panel activates the connected to the system, triggers
, and noties users and the security company. The Ajax app’s log
displays all the alarms and events. The notications contain the hub’s name, the
device’s name, and the to which the detector is assigned.
MotionCam (PhOD) Fibra is equipped with a tamper button and a battery. The
tamper reacts if someone tries to break or open the lid of the enclosure. If it
triggers, the notication is sent to the . The battery is used when the
8. Places for the cables.
9. . Triggers when an attempt is made to detach the detector
from the surface or remove it from the mounting panel.
Tamper button
10. Terminal strip connection socket.
11. QR code with the device ID. It is used to pair the device with an Ajax hub.
12. Terminal strip for the detector connection.
13. The holes to secure the wires with wire ties.
14. Captive screw. It is used to x the detector on the mounting panel.
sirens
scenarios
virtual room
Ajax apps
00:00
00:12

detector takes a photo, activates an IR backlight, and transmits an alarm. This
reduces the current consumption on the line to which the detector is connected
and increases the autonomy of the detector and the system.
Fibra data transfer protocol
The detector uses Fibra technology to transmit alarms and events. It is a wired
data transfer protocol for fast and reliable two-way communication between the
hub and connected devices.
Photo verication
Photo verication allows you to assess what is happening in the facility. Three
types of photo verication for MotionCam (PhOD) are available:
The detector takes Photo by Alarm only if the motion is detected and only when
the armed mode is on. By default, the Photo by Alarm feature is enabled for all
detectors.
The detector does not switch to armed mode instantly. The switching time depends on
two factors: the exit delay (specied in the detector settings) and the hub–detector ping
interval. The ping interval specied in the hub settings , Jeweller/Fibra section, by
default its meaning is 36 seconds.
How Ajax noties of alerts
More about Ajax motion detectors
What is the tamper
Learn more about Fibra protocol
Photo by Alarm.
Photo on Demand.
Photo by Scenario.

In the rst case, the delay is set by an administrator or a PRO user with admin rights. In
the second case, the delay occurs because the hub takes one ping interval to notify the
detector about the security mode change.
Photo on Demand feature is useful for checking the situation at the facility.
Depending on the settings, photos can be taken anytime or when MotionCam
(PhOD) is armed. By default, the Photo on Demand feature is disabled for all
users.
When Photo by Scenario is enabled, MotionCam (PhOD) takes pictures in case
of alarm from other Ajax devices. By default, the Photo by Scenario feature is
disabled for all detectors.
Also, Ajax Systems has the detector without the Photo on Demand and Photo by
Scenario functions. This product is called .
A built-in camera can take from 1 to 5 images with a resolution of 160 × 120 and
320 × 240 pixels, as well as up to 3 images with a resolution of 640 × 480 pixels.
The detector has an IR backlight for shooting in the dark, which activates with
insucient light. MotionCam (PhOD) takes black-and-white photos when
shooting in these conditions.
Features of alarm photo verication
More about the Photo on Demand feature
How to congure Photo on Demand
More about the Photo by Scenario feature
How to congure Photo by Scenario
MotionCam Fibra


Photos are played back in the application as a photo or animated series (if more
than 1 photo is taken). The number of pictures is congured in . To
view the received photos, click on the MotionCam (PhOD) Fibra notication in
the event feed.

You can view all the photos from the animated series individually by clicking on
the icon at the bottom of the screen.
Ajax apps


You can save photo verication as video or images by clicking the download
icon.
Photo delivery time
The photo delivery time to Ajax apps depends on the image resolution, Fibra
signal strength, and Internet connection speed. The alarm messages are
delivered immediately, regardless of the settings.

The table shows the delivery time for one photo when the signal strength
between the hub and MotionCam (PhOD) is 2–3 bars, and the hub is connected
via Ethernet or 4G (LTE).
Photo resolution Delivery time
160 × 120 pixels up to 7 seconds
320 × 240 pixels
(default) up to 9 seconds
640 × 480 pixels up to 20 seconds
Temperature compensation
Temperature compensation is necessary for the detector’s response to
movements, even if the room temperature is close to the human body
temperature. Read more about temperature compensation in .
Pet immunity
When properly installed and congured, MotionCam (PhOD) does not react to
pets weighing up to 20 kg and below 50 cm in height. To and
the detector, follow our recommendations.
this article
install congure
Why motion detectors react to animals and how to avoid it

Sending events to the monitoring station
The Ajax security system can transmit alarms to the monitoring
app as well as the central monitoring station (CMS) in the formats of SurGard
(Contact ID), SIA (DC-09), ADEMCO 685 and .
MotionCam (PhOD) Fibra can transmit the following events:
The Ajax devices are addressable, meaning that PRO Desktop app and CMS
receive events, device type, assigned name, and location (room, group). The list
of transmitted parameters may differ depending on the type of CMS and the
selected communication protocol.
You can nd the device ID, loop (zone) number, and the line number in the device .
Photos are sent to the security company monitoring station if the CMS software
supports photo verication. A list of such CMSs is .
supports receiving photo verication without additional setup.
Selecting the installation site
PRO Desktop
other protocols
Which CMS the Ajax security system can be connected to
1. Motion alarm.
2. MotionCam (PhOD) Fibra alarm photo verications.
3. Photo by Scenario.
4. Tamper alarm. Tamper recovery.
5. Loss of connection with the hub. Restoration of connection.
6. Permanent Deactivation / activation of the detector.
7. Alarm due to loss of the main power. Restoration of the main power.
States
available here
PRO Desktop

When choosing a spot to install MotionCam (PhOD), consider the parameters
that affect the operation of the device:
Follow these when designing the Ajax system project for an
object. The security system should be designed and installed by professionals.
The list of authorized Ajax partners is .
MotionCam (PhOD) Fibra cannot be installed
Fibra signal strength.
The length of the cable used to connect the detector to the hub.
Motion detection zone.
The camera’s viewing angle and the presence of obstacles in front of it.
recommendations
available here
1. Outdoors. This could damage the detector.
2. In places where objects and structures may obstruct the detector’s and the
camera’s view. For example, behind a ower or a column.
3. In places where glass structures may obstruct the detector’s view; it doesn’t
detect movement behind glass.
4. Facing the window to avoid direct sun rays hitting the detector lens. This can
lead to false alarms of the motion detector on the armed mode.
5. Opposite any objects with rapidly changing temperature — for example,
electric and gas heaters, air conditioners. This can lead to false alarms of
the motion detector on the armed mode.
6. Opposite any moving objects with a temperature close to that of the human
body — for example, opposite the swinging curtains above a radiator. This
can lead to false alarms of the motion detector on the armed mode.
7. In places with fast air circulation — for example, near fans, air conditioners,
open windows, or doors. This can lead to false alarms of the motion
detector on the armed mode.
8. Inside premises with temperature and humidity values that do not
correspond to the operating parameters. This could damage the detector.
9. In places with low or unstable Fibra signal strength.

Fibra signal strength
Fibra signal strength is determined by the ratio of the number of undelivered or
corrupted data packages to those expected over a specic time. The icon in
the Devices tab in Ajax apps indicates the signal strength:
The following factors affect the signal strength:
Motion detector detection area
The location of the detector determines the area to be monitored and the
effectiveness of the security system. When selecting the installation place,
consider the direction of the detector lens, viewing angles, and the presence of
obstacles to the view of the lens.
The detector can recognize motion at a distance of up to 12 metres. The
direction of the detector lens should be perpendicular to the intended entry path
into the premises. Ensure that furniture, house plants, vases, and decorative or
glass elements do not obstruct the view of the detector or its camera.
Three bars — excellent signal strength.
Two bars — good signal strength.
One bar — low signal strength; stable operation is not guaranteed.
Crossed out icon — no signal; stable operation is not guaranteed.
The number of devices on the Fibra line.
Cable length and type.
The correctness of the wire connections to the terminals.
What is Fibra Signal Strength Test

Horizontal viewing angle of the detector
Vertical viewing angle of the detector
When installing the detector, perform the . This allows you
to check the operation of the device and accurately determine the sector in
which the detector registers motion. If possible, take a couple of photos at the
installation site to ensure that the camera captures the desired area and that no
obstructions are blocking its view.
Designing and preparing
It is crucial to properly design the system project to install and congure the
devices correctly. The project must consider the number and types of devices at
the object, their exact location and installation height, the length of wired Fibra
lines, the type of cable used, and other parameters. Read to learn tips
for designing the Fibra system project.
When designing the project, consider the wiring diagram of the power cables
laid at the facility. Lay signal cables at a distance of at least 50 cm from power
cables in parallel. In case of an intersection, maintain a 90° angle between the
conductors.
Before installation, check the cables for bends and physical damage. During
installation, observe the bending radius specied by the manufacturer in the
Detection Zone Test
the article

cable specications. Otherwise, there is a risk of damaging or breaking the
conductor.
Different types of devices can be connected to the same Fibra line. For example,
you can use opening detectors, sirens, keypads, and MotionCam (PhOD) Fibra
on the same line.
If you are connecting multiple devices to a single Fibra line, make sure that they
are connected one after the other, as shown in the diagram.
Ajax systems also support Beam and Ring topologies. Ring connection will be available
in the next OS Malevich updates.
Cable length and type
Recommended cable types:
The wired connection range may vary if you use a different cable type. No other types of
cables have been tested.
Verication using a calculator
More about Fibra topologies
How to update OS Malevich
U/UTP cat.5 4 × 2 × 0.51, copper conductor.
Signal cable 4 × 0.22, copper conductor.

To ensure that the project is designed correctly and that the system will work in
practice, we have developed a . The calculator
helps check the communication quality and cable length for wired Fibra devices
when designing the system project for the selected conguration.
You can connect up to 100 devices to Hub Hybrid (with default settings).
Preparing for installation
Cable arrangement
When preparing to lay cables, check the electrical and re safety regulations in
your region. Strictly follow these standards and regulations. Tips for cable
arrangement are available in .
Cable routing
We recommend you to carefully read the section
before installation. Avoid deviations from the system project. Violating the basic
installation rules and the recommendations of this manual may lead to incorrect
operation and loss of connection with MotionCam (PhOD). Tips for cable routing
are available in .
Preparing cables for connection
Remove the insulating layer and strip the cable with a special insulation stripper.
The ends of the wires inserted into the device terminals must be tinned or
crimped with a sleeve. This ensures a reliable connection and protects the
conductor from oxidation. Tips for preparing the cables are available in
.
Installation and connection
Fibra power supply calculator
this article
Selecting the installation site
this article
this
article

Before installing MotionCam (PhOD), make sure that the optimal detector location has
been selected and that it meets the requirements of this manual. Before nal installation,
run the , and . During
installation adhere to the rules and requirements of regulatory legal acts on electrical
safety.
Connecting MotionCam (PhOD) Fibra to the hub
line power supply test detection zone test Fibra signal strength test
1. Turn off the power of lines in the . The function is available in
the Lines menu:
Hub → Settings → Lines → Lines Power Supply.
Ajax PRO app
2. Route the cable to connect MotionCam (PhOD) to the hub casing. Connect
the wires to the required hub line.
+24V — 24 V⎓ power terminal.
А, B — signal terminals.
GND — ground.
3. Remove the SmartBracket mounting panel from the detector. Carefully break
out the perforated part to output the cable from the rear side (top or
bottom).

If it is necessary to output cable from the bottom or the side, make holes
carefully in the places indicated in the gure using a drill at low speed.
4. If the detector is not the last device in the connection line, prepare a second
cable in advance. The ends of the wires of the rst and second cables,
which will be inserted into the detector terminals, must be tinned and
soldered together, or crimped with a sleeve.
5. Run the cable from the hub into the detector enclosure through the hole that
was made.
6. Connect the wires to the MotionCam (PhOD) terminals according to the
gure below. Be sure to follow the polarity and connection order of the
wires. Securely fasten the cable to the terminals. Secure the cable with ties.

+24V — 24 V⎓ power terminal.
А, B — signal terminals.
GND — ground.
7. If the detector is the last on the line, in case of Beam (Radial) connection,
install a terminating resistor jumper on the two contacts. Connect it to the
signal terminals of the MotionCam (PhOD). Terminating resistor (120 Ohm)
is included in the hub complete set.
8. Temporarily secure the SmartBracket panel to a vertical surface or corner
using double-sided adhesive tape or other temporary fasteners. This is
necessary to run the detector tests. The installation height is 2.4 metres.
9. Place the detector on the SmartBracket mounting panel.
10. Turn on line power in the Ajax PRO app (Hub → Settings → Lines →
Lines Power Supply). When the device is turned on, the green LED will light
up for about 1 second.

11. .Add the detector to the hub
12. Perform the .Detection Zone Test
How to run the functionality testing
13. Take some test photos to make sure that the camera is capturing the
required area and no obstacles are blocking its view.
14. Perform the . The recommended signal strength is
two or three bars. If the signal strength is one or zero bars, check the
connection correctness and the cable integrity.
Fibra Signal Strength Test
15. Run .Lines Power Test
16. If the detector passes the tests, x the SmartBracket mounting panel to a
vertical surface with bundled screws. Use at least two xing points (one is in
the perforated part of the mount above the tamper). The tamper reacts if
someone tries to break or open the lid of the enclosure — the notication
about this is sent to Ajax apps.
To x SmartBracket on the corner, screw the bundled fasteners to the side
recesses. Use at least two xing points (one is in the perforated part of the
mount above the tamper).

Adding to the system
The detector is compatible with and only with rmware
version or higher. Only veried partners can add and congure Fibra
devices in .
Before adding a device
When using other mounts, make sure they do not damage or deform the
mounting panel.
Double-sided adhesive tape can be used for temporary fastening as the device can
come unglued from the surface at any time. As long as the device is taped, the
tamper will not be triggered when the detector is detached from the surface.
17. Put the detector on the SmartBracket mounting panel and secure it with a
captive screw.
Hub Hybrid (2G) Hub Hybrid (4G)
OS Malevich 2.15.2
Ajax PRO apps
Types of accounts and their rights
1. Install the . Sign in or create .Ajax PRO app an account
2. Add the hub compatible with MotionCam (PhOD) Fibra to your app. Adjust
the settings and create at least one .virtual room
3. Make sure that the hub is on and has Internet access via Ethernet and/or
mobile network. You can do this in the Ajax app.

How to add MotionCam (PhOD) Fibra
Two ways to add devices are available in the : automatically and
manually. If the connection fails, check the wired connection’s correctness and
try again. If the maximum number of devices (100 for Hub Hybrid) has already
been added to the hub, you will receive an error notication while adding.
MotionCam only works with one hub. When the device is paired with a new hub,
it stops exchanging data with the previous hub. When the detector is added to a
new hub, it remains in the list of devices on the previous hub. You can remove
the device manually.
To add a device manually:
To automatically add a device:
4. Make sure the hub is disarmed and does not start updates. Check the hub
status in the Ajax app for this.
5. Make sure MotionCam is physically connected to the hub.
Ajax PRO app
1. Open the Ajax PRO app. Select the hub to which you want to add
MotionCam (PhOD).
2. Go to the Devices tab and click: Add Device.
3. Assign a name to the device.
4. Scan the QR code or enter the device’s ID manually. A QR code with ID is
placed on the detector enclosure under the SmartBracket mounting panel.
Also, it is duplicated on the device packaging.
5. Select a virtual room and a security group (if is enabled).Group mode
6. Press Add.
1. Open the Ajax PRO app. Select the hub to which you want to add the
detector.
2. Go to the Devices tab and click Add Device.
3. Select Add All Fibra Devices. The hub will scan the Fibra lines. After
scanning, all devices connected to the hub that have not yet been added to