AJAX FireProtect 2 (Heat) Jeweller User manual

FireProtect 2 (Heat) Jeweller User manual
Updated August 4, 2023
FireProtect 2 (Heat) Jeweller is a wireless re detector with a built-in siren.
Designed for indoor installation. Detects temperature rise. The detector also can
work without a hub.
It is available in two modications: with sealed batteries (has SB in the name)
that run 10 years, and with replaceable ones (has RB in the name) that run up to
7 years.
A list of compatible hubs and range extenders is . FireProtect 2 (Heat)
detector is compatible only with hubs on and higher.
The detector operates as part of the Ajax system, communicating with the hub
via the secure radio protocol. The hub communication range is up to
1,700 meters without obstacles.
available here
OS Malevich 2.15
Jeweller
Buy FireProtect 2 (Heat)

Versions of the detector with other sensor combinations are also available. All Ajax re
detectors are .
Functional elements
available here
1. Detector front panel with . To activate the button, press the
center of the panel.
Test/Mute button
2. SmartBracket mounting panel. To remove the panel, turn it
counterclockwise.
3. Device QR code and ID (serial number). It is used to add the detector to the
Ajax system.
4. . Triggers when an attempt is made to detach the detector
from the surface or remove it from the mounting panel.
Tamper button
5. Power button.
6. Detector certication information.

Operating principle
FireProtect 2 (Heat) is a wireless re detector designed for indoor installation.
Available in two versions:
The Battery Life Optimization feature must be enabled to ensure such a lifetime for built-
in and pre-installed batteries.
7. Siren.
8. Green LED indicator.
9. Yellow LED indicator.
10. Red LED indicator.
11. First thermistor. Detects dangerous temperatures.
12. Second thermistor. Detects dangerous temperatures.
With sealed batteries. Such a detector has SB in its name. Built-in battery
life is 10 years. After the batteries are discharged, the detector should be
replaced with a new one.
With replaceable batteries. Such a detector has RB in its name. Pre-installed
battery life is 7 years. When the batteries are discharged, they can be
replaced with new ones.
Learn more
00:00
00:12

The detector is equipped with a siren (piezoelectric buzzer) for audible
notication of alarms and events with a volume of up to 85 dB (at a distance of
3 m from the detector). The detector is always active and reacts to a re 24/7,
regardless of the system’s security mode.
FireProtect 2 is protected by . The tamper controls the removal of the
detector from the SmartBracket mounting panel: the detector reacts with LED
indication and sends notications to users in Ajax apps and the security
company monitoring station.
respond to FireProtect 2 alarms and perform user-
dened actions using . For example, the relay
can turn on the ventilation system and emergency lighting when an alarm
occurs.
Heat sensor
Two built-in thermistors of A1 class detect a rapid rise and exceeding the
temperature threshold in FireProtect 2. Such thermistors notify of alarm when a
rapid temperature rise or static temperature is detected in the range of+54°C to
+65°C.
FireProtect 2 reports that the temperature threshold has been exceeded as soon
as its value exceeds +64°C. The detector reports a rapid temperature rise if the
indicator increases by 10°C within one minute. If the temperature indicator rises
sharply by 20°C or more, the detector alerts immediately.
Test/Mute button
Тo activate the Test/Mute button, press lightly on the centre of the front panel
with your hand. Use a suitable item (mop handle) if you can’t reach up the
detector with your hand. Test/Mute is a mechanical button placed under the
front panel of the detector.
The button performs several functions:
How to replace batteries in FireProtect 2 RB (Heat)
tamper
Ajax automation devices
automation scenarios WallSwitch
In normal mode, it starts the .detector self-test

Interconnected Fire Detectors Alarms*
All re detectors of the FireProtect 2 product line support the Interconnected
Alarm feature. This function activates the built-in sirens of all re detectors in
the system as soon as at least one of the re detectors detects an alarm. Sirens
of FireProtect 2 detectors are activated within 20 seconds after an alarm is
detected. and are activated over a detector ping
interval set in the Jeweller (or Jeweller/Fibra) settings, but no later than 60
seconds after.
FireProtect 2 detectors have different sound and LED indications of alarm types
to make it easier for users to distinguish between them. In case of
interconnected alarm, FireProtect 2 detectors indicate exactly the alarm type
detected by the initiating detector. The initiating detector additionally indicates
the alarm by LED. Instead, FireProtect and FireProtect Plus detectors notify all
types of alarms with the same sound.
*The Interconnected Fire Detectors Alarm function is not certied according to EN 14604
and EN 50291
Sending events to the monitoring station
The Ajax system can transmit events and alarms to the monitoring
app as well as the Central Monitoring Station (CMS) via SurGard (Contact ID),
SIA DC-09 (ADM-CID), ADEMCO 685, and other protocols. The list of supported
protocols is .
In case of an alarm, it mutes the detector alarm or of
all re detectors in the system for 10 minutes.
Interconnected Alarm
In case of a fault or low battery level it mutes the sound and LED indication
for 12 hours.
FireProtect FireProtect Plus
How to set Interconnected Fire Detectors Alarms
How to mute Interconnected Fire Detectors Alarms
PRO Desktop
available here
Which CMSs Ajax connects to

Addressability of Ajax devices allows you to send not only events but also the
type of the device, the name, virtual room, and security group assigned to it to
the PRO Desktop and to the CMS. The list of transmitted parameters may differ
depending on the type of the CMS and the selected communication protocol.
The ID and detector loop (zone) number are available in the detector .
Adding to the system
Before adding a device
A can connect the device to the hub.
To connect to the hub, the detector should be within the coverage area of the
hub radio network. To operate via a rst connect the
detector to the hub and then to the range extender. You can do this in the range
extender settings in Ajax apps.
How to connect FireProtect 2 to a hub
States
1. Install the .Ajax app
2. if you don’t have one.Create an account
3. Add a to your app. Set the required
settings and create at least one .
hub compatible with the detector
virtual room
4. Make sure that the hub is on and has Internet access via Ethernet, Wi-Fi,
and/or mobile network. You can do this in the Ajax app or by looking at the
LED indicator of the hub: it should light up white or green.
5. Make sure that the hub does not start updates and that it is disarmed by
checking the status in the Ajax app.
PRO or a user with system setup rights
radio signal range extender
1. Open the .Ajax app

Once connected, FireProtect 2 will appear in the hub device list in the Ajax app.
Device status update depends on the ping interval set in the Jeweller or
Jeweller/Fibra settings. The default value is 36 seconds.
FireProtect 2 works with only one hub. When connected to a new hub, the
detector stops transmitting data to the old hub. Once added to a new hub,
FireProtect 2 is not removed from the list of devices of the old hub. This must be
done manually in the Ajax app.
Autonomous operation mode
2. Select the hub if you have several of them or if you are using the
.
Ajax PRO
app
3. Go to the Devices tab. Press Add Device.
4. Enter the name of the device.
5. Scan the QR code or enter the ID manually. QR code is located on the rear
part of the enclosure (under the mounting panel) and on the device
packaging. The device ID can be found below the QR code.
6. Select the and security group (if the is enabled).virtual room group mode
7. Click Add; the countdown will begin.
If the maximum number of devices is added to the hub, when you add the device,
you will get a notication about exceeding the device limit. The number of devices
that you can connect to the hub depends on the .central unit model
8. Turn on the detector by holding the power button for 3 seconds. The hub
connection request is sent only if the detector is enabled. If the detector
fails to connect to the hub, try again in 5 seconds.
The detector cannot connect to the hub if they operate on different radio
frequencies. The radio frequency range of the devices depends on the region of
sale. Please contact for information on the operating frequency
range of your devices.
technical support

FireProtect 2 detectors can be used autonomously without connecting to an
Ajax hub. In this case, the detector noties of re with only a built-in siren
andLED . Users don’t receive notications on any , including
, or . The
feature is also unavailable for this operation mode.
To use the detector autonomously, follow these steps:
During a self-test FireProtect 2 noties about each step with a built-in siren and
LED indication. Once a self-test is completed, the LED turns off, and
the detector works autonomously.
In case of an alarm, press the Test/Mute button or eliminate the cause of the
alarm to mute the siren.
Indication
indication Ajax apps
Ajax Translator PRO Desktop Interconnected Fire Detectors Alarms
1. Select the optimal location of the detector using the recommendations in
the place section.Selection of installation
2. Mount the detector on the SmartBracket panel as described in the
section.Installation
3. Press the power button to switch on the detector.
4. Start a with the Test/Mute button. Press the centre of the front
panel and hold it for 1.5 seconds.
self-test
indication
00:00
00:06

LEDs and the built-in siren of the detector can report alarms as well as certain
states of the detector.
LED indication Sound indication Event Notes
The red LED ashes
continuously.
The siren sounds in
time with the LED
indication.
Alarm by:
The detector stops
alarming as soon as
its sources are
eliminated.
Also, you can mute
the alarm by pressing
the
or in the Ajax
app.
The LED and sound
indications resume if
the source of the
alarm is still present
after the muting timer
(10 minutes) has
expired.
The red LED ashes
every 4 seconds. No. Muted alarm.
The detector stops
alarming as soon as
its source is
eliminated.
The red LED ashes 2
times in a row. No. Restore after alarm.
If the source of the
alarm is removed, the
detector is restored
automatically.
The yellow LED lights
up for 1 second. No.
Tamper alarm.
The detector is
removed from the
SmartBracket
mounting panel.
The green LED lights
up for 1 second. No.
The detector is
installed on the
SmartBracket
mounting panel.
Turns on when the
tamper is triggered.
Green, yellow, and red
LEDs light up in turn,
No. Turning the detector
on.
To turn on the
detector, hold the
rapid temperature
rise;
temperature
threshold
exceeding.
Test/Mute
button

then go off. power button for 1
second.
Green, yellow, and red
LEDs light up at the
same time, then go
off in reverse order.
No. Turning the detector
off.
To turn off the
detector, hold the
power button for 2
seconds.
The green LED is
permanently on. No. Connection to the hub in progress.
The indication turns
off after the detector
connection to the hub.
The green LED ashes
6 times in a row. No.
The detector has been
removed from the
hub.
The indication turns
on when the detector
receives information
that it has been
removed from the
hub.
The yellow LED
ashes 2 times in a
row every minute.
The siren beeps in
time with the LED
indication every
minute.
Malfunction detected.
All malfunctions are
displayed in the
detector in
Ajax apps. Fields with
malfunctions are
highlighted in red.
If the detector needs
to be repaired, contact
.
The yellow LED
ashes once per
minute.
The siren beeps in
time with the LED
indication once per
minute.
Low battery level.
You can replace
batteries in a detector
with replaceable
batteries only (has RB
in its name). A
detector with sealed
batteries (with SB in
the name) should be
replaced with a new
one after the batteries
are discharged.
The yellow LED
constantly ashes.
No. The battery is
completely
You can replace
batteries in a detector
states
Technical
Support
How to replace
batteries in
FireProtect 2 RB
(Heat)

discharged. with replaceable
batteries only (has RB
in its name). A
detector with sealed
batteries (has SB in
its name) should be
replaced with a new
one after the batteries
are discharged.
The red LED ashes 5
times.
The siren beeps 5
times. Performing a self-test.
The test can be
started by pressing
the
or in the Ajax
app in the detector
settings.
Detector testing
Functionality testing
The test allows you to check the status of the detector’s sensors. You can run it
in two ways: by pressing the Test/Mute button on the detector or in Ajax apps.
If the detector is in an alarm state, the self-test is not available.
To run the test using the Test/Mute button, press the center of the front panel
and hold for 1.5 seconds.
To run the test in the Ajax app:
How to replace
batteries in
FireProtect 2 RB
(Heat)
Test/Mute
button
1. Open the Ajax app.

After starting the test, the red LED of the detector ashes 5 times in a row. The
detector’s siren beeps in time with the LED indication. When the test is over,
users receive a notication about the detector state in Ajax apps.
The detector also noties about the test result with sound and LED indications.
If the test is failed and a malfunction is detected, the detector starts to indicate
a malfunction 3 seconds after the test is begun: the yellow LED ashes twice,
and the siren beeps in time with the LED indication.
The self-test does not start immediately, but no later than 30 seconds after pressing the
Test/Mute button or running from the Ajax app.
If no sound and LED indications occurred during the self-test, the detector may not be
used. Contact our .
Testing at the place of installation
Ajax system provides several tests to select the correct installation place of
devices. Jeweller Signal Strength Test is available for FireProtect 2. The test
determines the strength and stability of the signal at the intended location of the
device.
To run the test in the Ajax app:
2. Select the hub if you have several of them or if you are using the
.
Ajax PRO
app
3. Go to the Devices menu.
4. Select FireProtect 2 (Heat).
5. Go to the settings by clicking on the gear icon .
6. Click on the Device Self-test eld.
Technical Support
1. Select the hub if you have several of them or if you are using the
.
Ajax PRO
app
2. Go to the Devices menu.

The test does not start immediately, but the waiting time does not exceed the duration of
one detector ping interval. The default value is 36 seconds. You can change the detector
ping interval in the Jeweller (or Jeweller/Fibra) menu in the hub settings.
Icons
The icons show some of the detector states. You can view them in Ajax apps in
the Devices tab.
Icon Meaning
Jeweller signal strength between the detector and the hub or the radio signal
range extender. The recommended value is two or three bars.
Battery charge level of the device.
The Interconnected Fire Detectors Alarm feature is activated.
The detector operates in the Always Active mode.
The icon is displayed permanently. FireProtect 2 is always active and responds
to a re 24/7, regardless of the system’s security mode.
The detector operates through a .
3. Select FireProtect 2 (Heat).
4. Go to the settings by clicking on the gear icon .
5. Select Jeweller Signal Strength Test.
6. Perform the test following the tips in the app
Learn more
Learn more
Learn more
Learn more
radio signal range extender

The detector is permanently deactivated.
The detector has detected a rapid temperature rise.
The detector has detected that the temperature threshold has been exceeded.
The detector was removed from the SmartBracket mounting panel, or the
enclosure integrity was violated in another way. Check the mounting of the
detector.
The detector’s siren plays an alarm sound.
Malfunction detected. A list of malfunctions is available in the detector
.
The detector has tamper triggering events deactivated.
States
The states include information about the device and its operating parameters.
You can see FireProtect 2 (Heat) states in Ajax apps. To access them:
Ajax apps display three FireProtect 2 temperature parameters. The rst one
shows the air temperature in the room where the detector is installed. The other
two (Temperature Threshold Exceeded and Rapid Temperature Rise) show
whether re-related temperature changes are detected. These values may differ
from the temperature in the room.
Learn more
states
Learn more
1. Open the Ajax app.
2. Select a hub if you have several of them or if you are using the Ajax PRO
app.
3. Go to the Devices tab.
4. Select the device from the list.

Parameter Meaning
Temperature
Air temperature in the premise where
FireProtect 2 is installed. Measured in Celsius
or Fahrenheit degrees depending on the app
settings.
In the normal state, the temperature value is
displayed in black.
When the temperature rises, the eld is
highlighted with red.
Jeweller Signal Strength
Jeweller signal strength between FireProtect 2
and the hub or radio signal range extender.
The recommended value is two or three bars.
Jeweller is a protocol for transmitting
FireProtect 2 events and alarms.
Connection via Jeweller
Connection status between FireProtect 2 and
the hub or radio signal range extender via
Jeweller:
Battery Charge The battery power level of the device:
When the batteries are discharged, users and
the CMS receive a notication.
After the low battery notication, the detector is
able to operate for another month under normal
conditions. In case of an alarm, the battery
Online — the detector is connected to the
hub or radio signal range extender. Normal
state.
Oine — no connection between the
detector and the hub or radio signal range
extender. Check the detector connection.
OK — detector batteries have sucient
charge. Normal state.
Battery low — detector batteries are
discharged.

power is enough to ensure 4 minutes of the
sound and LED indication operation.
You can replace batteries in a detector with
replaceable batteries only (has RB in its name).
A detector with sealed batteries (with SB in the
name) should be replaced with a new one after
the batteries are discharged.
Lid
The status of the detector`s tamper that
responds to detachment of the device from the
surface or opening of the enclosure:
Temperature Threshold Exceeded
Alarm state if temperature threshold is
exceeded:
If a temperature threshold exceeding is
detected, the text eld highlights red.
Rapid Temperature Rise Alarm by rapid temperature rise:
How the battery charge is displayed
Battery life calculator
How to replace batteries in
FireProtect 2 RB (Heat)
Open — the detector is removed from the
SmartBracket mounting panel, or the
enclosure integrity is violated in another
way. Check the mounting of the detector.
Closed — the detector is installed on the
SmartBracket mounting panel. The integrity
of the device enclosure and the mounting
panel is not violated. Normal state.
Learn more
No — normal state, the detector does not
detect a temperature threshold exceeding.
Alarm — the detector has detected a
temperature threshold exceeding.
Learn more

If a rapid temperature rise is detected, the text
eld highlights red.
Permanent Deactivation
Shows the status of the device permanent
deactivation function:
Firmware FireProtect 2 rmware version.
Device ID
ID (serial number) of FireProtect 2. Also
available on the detector’s enclosure (under the
mounting panel) below the QR code and on the
packaging box.
Device No. The number of FireProtect 2 loop (zone). Events
are sent to the CMS from this number.
Settings
To change FireProtect 2 (Heat) settings in the Ajax app:
No — normal state, the detector does not
detect a rapid temperature rise.
Alarm — the detector has detected a rapid
temperature rise.
Learn more
No — the device operates in normal mode.
Lid only — detector’s tamper triggering
notications are disabled.
Entirely — the detector does not execute
system commands, does not participate in
automation scenarios, and does not send
notications of alarms, malfunctions, and
other events to the CMS and system users.
In this case, the detector will continue to
operate autonomously and indicate alarms
using the built-in siren.
Learn more
1. Open the Ajax app.

Settings Meaning
Name
Detector name. Displayed in the list of hub
devices, text of SMS and notications in the
events feed.
To change the name, click on the text eld.
The name can contain up to 12 Cyrillic
characters or up to 24 Latin characters.
Room
Selecting the virtual room to which FireProtect 2
is assigned.
The room name is displayed in the SMS text
and notications of the events feed.
To change the room, click on the eld.
Alert with a siren
If the temperature threshold exceeded
When this option is enabled, the
connected to the system are activated when the
detector detects a temperature threshold
exceeding.
If rapid temperature rise detected
When the option is enabled, the
connected to the system are activated when the
detector detects a rapid temperature rise.
Jeweller Signal Strength Test Switches the detector to the Jeweller signal
strength test mode. The test helps to determine
the optimal place for installing FireProtect 2.
2. Select the hub if you have several of them or if you are using the
.
Ajax PRO
app
3. Go to the Devices tab.
4. Select the device from the list.
5. Go to Settings by clicking on the gear icon .
6. Set the required settings.
7. Click Back to save the settings.
Ajax sirens
Ajax sirens

The test shows the signal strength between the
detector and the hub or radio signal range
extender via the Jeweller wireless data transfer
protocol.
The recommended value is two or three
divisions.
Device Self-test
Runs a detector self-test.
User Guide Opens FireProtect 2 User Manual in the Ajax
app.
Permanent Deactivation
Allows to deactivate the device without
removing it from the system. Three options are
available:
Delete device Unpairs FireProtect 2 from the hub and deletes
its settings.
Battery life optimization setting
The Battery Life Optimization feature is provided to save the detectors’ battery
charge. It is available only for hubs on or higher with
Learn more
Learn more
No — the device operates in normal mode.
Lid only — detector’s tamper triggering
notications are disabled.
Entirely — the detector does not execute
system commands, does not participate in
automation scenarios, and does not send
notications of alarms, malfunctions, and
other events to the CMS and system users.
In this case, the detector will continue to
operate autonomously and indicate alarms
using the built-in siren.
Learn more
OS Malevich 2.14

FireProtect 2 detectors connected. This feature is enabled by default.
When the Battery Life Optimization feature is enabled, the hub increases the
ping interval for FireProtect 2 detectors.
This feature doesn’t affect alarm notication delivery time.
To disable the Battery Life Optimization feature:
If the Battery Life Optimization feature is disabled:
Selection of installation place
The detector is designed for indoor installation only.
The coverage area of one FireProtect 2 (Heat) is 50 to 60 m², depending on the
type of premises.
1. Open the Ajax app.
2. Select the hub with FireProtect 2 detectors connected.
3. Go to:
Hub → Settings → Service → Fire Detectors Settings.
4. Disable the Battery Life Optimization toggle.
5. Click Back to save the settings.
FireProtect 2 SB (Heat) built-in battery life is 5 years (instead of 10).
FireProtect 2 RB (Heat) pre-installed battery life is 3.5 years (instead of 7).