When selecting an installation location for DoorProtect, take
into account any obstacles impairing the radio signal
transmission.
The detector is equipped with two magnets - small and big,
with the magnet operation ranges of 1 cm and 2 cm
accordingly. The magnet is attached to the moving part of the
door (window) to the right of the detector. If necessary, the
detector may be positioned horizontally.
1. Fix the SmartBracket attachment panels of the detector
and magnet with bundled screws or other no less reliable
attachment hardware.
2. Put the detector on the panel - single blink of the light
indicator will confirm that the tamper has been actuated.
Prior to the attachment of the detector to a surface with
screws, please perform signal strength test in the Ajax
Security System application for at least a minute. This will
demonstrate communication quality between the detector
and the hub and ensures proper installation place selection.
The detector is connected to the hub and set up via the
Ajax Security system mobile application. To establish
connection please locate the detector and the hub within
the communication range and follow the device adding
procedure.
A wire detector with a NC type contact may be connected
to DoorProtect using an outside-mounted terminal clamp.
To lead out the wire from the DoorProtect body, break out
the plug.
Before using the external detector connected to the
terminal clamp, activate it in the DoorProtect settings.
If the detector is located in a room requiring 24-hour
control, activate the "Always active" mode - DoorProtect will
be actuated in case of opening, even if the system is not in
the arming mode.
1. DoorProtect.
2. Battery CR123A (pre-installed).
3. Big magnet.
4. Small magnet.
5. Outside-mounted terminal clamp.
6. Installation kit.
7. Quick Start Guide.
Do not install the detector:
1. Outside the premises (outdoors).
2. Nearby any metal objects and mirrors causing radio
signal attenuation or screening it.
3. Within any premises with the temperature and
humidity beyond the range of permissible limits.
FUNCTIONAL ELEMENTS
LOCATION SELECTION MOUNTING THE DEVICE
CONNECTION AND SETTING UP
EN
DoorProtect is a wireless door and window opening
detector, equipped with a sealed contact reed relay
designed for processing more than one million openings.
It has a socket for connecting an external detector.
DoorProtect is connected to the Ajax security system via
the protected Jeweller protocol, with an effective
communication range of up to 1,200 meters without
obstacles. It can operate up to 7 years from a bundled
battery, and is designed for use indoors.
IMPORTANT: This Quick Start Guide contains general
information about the DoorProtect. Before using the device,
we recommend to reviewing the User Manual on the
website:
ajax.systems/support/devices/doorprotect
TECH SPECS
COMPLETE SET
WARRANTY
Maximum RF output power Up to 20 mW
Modulation FM
Frequency band 868.0-868.6 mHz
Radio signal Up to 1,200 m
(any obstacles absent)
Socket for connecting
wire detectors Yes, NC
Power supply 1 battery CR123A, 3 V
Up to 7 years
Battery life
Operating
temperature range From 0°С to +50°С
Operating humidity Up to 80%
Dimensions Ø20х90 mm
29 g
Weight
Manufacturer: Research and Production Enterprise “Ajax” LLC
Address: Sklyarenko 5, Kyiv, 04073, Ukraine
By request of Ajax Systems Inc.
www.ajax.systems
1 - DoorProtect.
2 - Big magnet.
3 - Small magnet.
5 - SmartBracket
attachment panel
(perforated part is
required for
actuating the tamper
in case of any
attempt to tear off
the detector from the
surface).
6 - External detector
connection socket.
7 - QR code.
8 - Device switch.
9 - Tamper button.
4 - Light
indicator.
5
4
8
7
3
6
9
21
Blinks 2 times per second
Excellent
signal level
Good
signal level
Poor
signal level
No signal
Lights with interruptions
once every 1.5 seconds
Blinks 5 times per second
Lights up for a short time
once every 1.5 seconds
Status indicator Signal level
Warranty for the Ajax Systems Inc. devices is valid for 2
years after the purchase and does not apply to the
supplied battery. If the device does not work correctly, you
should first contact the support service—in half of the
cases, technical issues can be solved remotely!
The full text of the warranty is available on the website:
ajax.systems/warranty
Technical support:
Quick Start Guide
Magnetic opening detector
Model Name: Ajax DoorProtect Detector actuation
threshold
1 cm (small magnet)
2 cm (big magnet)
Anti-tamper switch Yes
User Agreement:
ajax.systems/end-user-agreement
This product can be used across all EU member states.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
IMPORTANT INFОRMATION
This device in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
All essential radio test suites have been carried out.
Wireless magnetic door detector
8
To connect the detector to a third party security central unit
using the Ajax uartBridge or Ajax ocBridge Plus integration
module, follow the recommendations in the user manual of
the respective device.
3. Fix the magnet on the attachment.
