Assa Abloy Whitco Cyl4 Window Bolt User manual

Window Bolt
Stylish high security window lock
10mm
34
Whitco Window Bolt: For use with most aluminium and timber windows and narrow stile french doors.
Operation: Key lockable bolt provides push to bolt and key to deadlock operation. Note: Cylinder can be located
on either side of bolt for convenient operation.
Application: Provides safe bolting or deadlocking of most window types and narrow stile french doors.
CYL4®: Please see your local hardware retailer or locksmith prior to installation if you are having this product
keyed to other locks in your home.
Fixing Instructions
1
Remove bolt and screw cover
With unit unlocked remove bolt with
twist and pull action. Remove cover by
twisting a flat head screwdriver in the
end slots.
Mark fixing screw locations through
packer
Check clearance of screws with glass line
and ensure bolt will not interfere with
frame in the unlocked position (Leave at
least 10mm clearance between lock body
and frame). Drill two 4mm pilot
holes to suit fixing screws where marked.
Drilling Holes Accurately - We
recommend centre punching holes
prior to drilling.
Remove key stop for 5 pin key
Note: Optional - this step is not required if
using the key supplied in the pack.
When using a 5 pin key (keyed alike with
door locks), snap off triangular cylinder
stop, on the back of product using a
flat screwdriver as shown and mount
lock using 4mm packer to provide rear
clearance for longer key.
Determine fixing location
Select fixing position, refer to diagrams above. Hold assembled
lock in desired mounting position and check for:
• Orientation of cylinder (bolt can be inserted from either end)
• Use packer when bolt doesn’t engage frame
• When using a 5 pin key (refer step 4), use either the 4mm packer
or drill a 16mm clearance hole of 5mm depth to accommodate
point of the key
Extra Clearance - For extra clearance and strength it may be
necessary to use the packer for optimal bolt engagement.
Note: we recommend using a packer when fitting lock to
casement or awning windows.
Q50012M 0907-2
Before
After
Components
Ferrule Lock Body Packer
Aluminium Screws
Timber Screws
Ferrule Screws Keys
2
Awning
Windows
Fit lock at
bottom of
window
Sliding
Windows
Fit lock
at end of
either window
Casement
Windows
Fit lock
in middle
of window
Option 1
Fit bolt to top
and bottom
of last closing
door
Option 2
Fit bolt to top
and bottom of
both doors
French Doors
1
2
Option 1
With both windows
sliding, fit to top
of lower sash locking
into upper sash
Option 2
With fixed top
window, fit to lower
sliding sash
Double Hung
Windows
1
2
10mm
Before
After

Window Bolt
Stylish high security window lock
Ensure bolt engages fully so that key can be
locked. Pull bolt out to unlocked position
and open window to check that bolt
remains clear of obstacles throughout the
range of window movement.
Attach lock to frame
Screw lock body into position using the
appropriate screw for the frame material.
Replace bolt, check operation and refit
screw cover.
Note: The timber screw has a sharp point
and the aluminium screw has a flat tip.
56
8
6 7
Check operation
Mark and drill bolt hole
With window firmly closed, tap end of
bolt to mark drilling location and drill
10mm diameter hole, deep enough for
full movement of bolt.
Fit ferrule
Hold ferrule in position over bolt hole
and mark fixing locations. Drill two
2.5mm pilot holes to suit fixing screws
and fix ferrule into position.
2.5mm
10mm
2.5mm
10mm
2.5mm
2.5mm
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Road, Oakleigh, VIC 3166
ABN 90 086 451 907 ©2006
www.assaabloyasiapacific.com
Whitco Warranty
ASSA ABLOY Australia Pty Limited (“ASSA ABLOY”) warrants its Whitco products against defects in workmanship and materials for a period of 10 years from
the date of purchase by the retail customer, subject to the limitations and exclusions set out in this Warranty. If, within this period the product is found to be
defective, and none of the limitations and exclusions set out in this Warranty apply, ASSA ABLOY will supply the same or equivalent product free of charge.
This is the only remedy granted by ASSA ABLOY under this Warranty. Limitations: All window screen and door screen products are warranted for a period of
12 months from the date of purchase by the retail customer. This limitation does not apply to key locks and hinges included in window screen and door screen
products, to which the full ten year warranty applies. Exclusions: This Warranty does not cover: 1. Damage to or malfunction or failure of the Whitco product
caused or contributed to by: (a) misuse, abuse, accidental or intentional damage; (b) improper installation or failure to follow fitting instructions; (c) improper
maintenance; (d) use contrary to instructions provided by ASSA ABLOY; (e) fair wear and tear; (f) any modification or repair which has not been authorized by
ASSA ABLOY; (g) use of substitute or replacement parts or cylinders other than genuine ASSA ABLOY parts or cylinders. 2. The cost of:(a) removal, replacement
or reinstallation of the Whitco product; (b) freight costs and travelling time; (c) any modification or repairs to a Whitco product, unless authorised by ASSA
ABLOY. 3. Damage caused by corrosion when the Whitco product is used in a corrosive environment. 4. Tarnish, damage to or deterioration of soft finishes such
as Bronze, Brass and other Antique finishes, which are subject to deterioration due to environmental conditions, frequency of use and other factors. 5. Damage
to Gold, Chrome and powder coated finishes caused by damage to the protective layer. 6. Deterioration in colour and performance of polymer materials. 7.
Personal injury, property damage or economic loss, however caused.
Patent: NZ 326495, AU 727454, GB 2325021