Allied Telesis TQ6702e GEN2 User manual

613-003121 Rev. A
TQ6702e GEN2
OUTDOOR WIRELESS ACCESS POINT
AT-TQ6702e GEN2
IEEE802.11ax Dual-radio 5GHz/2.4GHz 8x8+4x4 Wireless AP
Installation Guide

Copyright  2023 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for
any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related
to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the
possibility of such damages.

3
Electrical Safety and Emissions
Standards
This product complies with the standards described in the following sections:
“Federal Communications Commission Interference Statement” on page 3
“European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical
and Electronic Equipment” on page 4
“Safety and Electromagnetic Emissions” on page 4
“Translated Safety Statements” on page 8
Federal Communications Commission Interference Statement
Declaration of Conformity
Manufacturer Name: Allied Telesis, Inc.
Declares that the product: Indoor and Outdoor Wireless Access Point
Model Number: AT-TQ6702e GEN2
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.

4
Caution
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.  E80
Warning
Only trained and qualified personnel are allowed to install or to replace this equipment.  E14
Professional installation is required.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment using the dipole antenna should be installed and operated with
minimum distance 46 cm between the radiator and your body; this equipment using the patch
antenna should be installed and operated with minimum distance 51cm between the radiator and
your body.
European Union Restriction of the Use of Certain Hazardous
Substances (RoHS) in Electrical and Electronic Equipment
This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the
Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied
Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring
incoming materials, and maintaining manufacturing process controls.
Note
For additional statements, refer to Appendix A, ”Technical Specifications and Statements” on
page 83.
Safety and Electromagnetic Emissions
Standard Compliance
• RoHs compliant
• JGPSSI/JIG level A

5
Wire Communications
• IEEE 802.1
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.3x
• IEEE 802.3ab
• IEEE 802.3af
• IEEE 802.3ah
• IEEE 802.3bt
Wireless Communications
• IEEE 802.11 DSSS
• IEEE 802.11a OFDM
• IEEE 802.11b DSSS/FHSS
• IEEE 802.11g OFDM
• IEEE 802.11n
• IEEE802.11ac
• IEEE802.11ax
Safety
• UL 62368-1
• UL 60950-22
• TUV T-mark
• EN 62368-1:2014 / A11:2017
• EN60950-22
• CB62368-1 + CB60950-1
• IEC60950-22
• UL2043
Electromagnetic Interference (EMI)
• FCC Part 15 Subpart B/ Class B
• EN55032 Class B
• EN60601-1-2
• EN301489-1/-17
• VCCI Class B
• CISPR 32 Class B
• AS/NZS CISPR 32

6
Electromagnetic Susceptibility - EN55024
• IEC 61000-3-2:2014
• IEC 61000-3-3:2013
• IEC 61000-4-2:2008
• IEC 61000-4-3:2006+A1:2007+A2:2010
• IEC 61000-4-4:2012
• IEC 61000-4-5:2017
• IEC 61000-4-6:2013
• (IEC 61000-4-8:2009)
• IEC 61000-4-11:2014/AMD:2017
• IEC 61000-3-2:2014
• IEC 61000-3-3:2013
FCC
• 47 CFR Part 15, Subpart C
• 47 CFR Part 15, Subpart E
• DFS
IC
• ICES-003 issue 6
• RSS-102
• RSS-247 issue 2
CE
• RED Directive 2014/53/EU
• EN55032:2015+AC:2016 (CISPR32:2015/COR1:2016)
• EN 55024:2010+A1:2015
• EN55035
• EN 50385
• EN 301489-1 V 2.1.1
• EN 301489-17 V 3.1.1
• EN 300328 V 2.2.2
• EN 301893 V2.1.1
• EUROPEAN COUNCIL DIRECTIVE
• 2014/30/EU
• DFS
• IEC/EN60601-1-2
• UKCA

7
RCM
• AS/NZS CISPR 32: 2015
• AS/NZS 4268: 2017
China SRRC
Hong Kong OFCA
India WPC
Indonesia SDPPI
Israel MOC
Japan
• ARIB STD-T66
• ARIB STD-T71
Korea KC
Malaysia SIRIM
Mexico NOM
Philippine NTC
Singapore IMDA and TS SRD
South Korea KC
Taiwan
• CNS15936
• NCC
• CNS15598-1
Thailand NBTC
Vietnam MIC
Complies with
IMDA Standards
DB102434

8
Translated Safety Statements
Important: Safety statements that have the  symbol are translated into multiple languages in the
Translated Safety Statements document at www.alliedtelesis.com/library.
Remarque: Les consignes de sécurité portant le symbole  sont traduites dans plusieurs langues
dans le document Translated Safety Statements, disponible à l'adresse www.alliedtelesis.com/
library.

9
Table of Contents
Preface ............................................................................................................................................................ 15
Safety Symbols Used in this Document..................................................................................................... 16
Professional Installation Instructions.......................................................................................................... 17
Contacting Allied Telesis............................................................................................................................ 18
Chapter 1: Product Description ................................................................................................................... 19
Features of the TQ6702e GEN2 Access Point .......................................................................................... 20
TQ6000 GEN2 Models............................................................................................................................... 22
Management Tools .................................................................................................................................... 23
Web Browser ....................................................................................................................................... 23
Vista Manager EX and AWC Plug-in ................................................................................................... 23
SNMPv1 and v2c................................................................................................................................. 23
TQ6702e GEN2 Access Point.................................................................................................................... 24
LAN Port .............................................................................................................................................. 25
Power over Ethernet (PoE++) ............................................................................................................. 26
Connector Type ................................................................................................................................... 26
Speed .................................................................................................................................................. 26
Duplex Mode ....................................................................................................................................... 26
Automatic MDIX Detection .................................................................................................................. 27
Maximum Distance .............................................................................................................................. 27
Port Pinouts ......................................................................................................................................... 27
LEDs.................................................................................................................................................... 27
Reset Button........................................................................................................................................ 28
Ethernet Cable Requirements ............................................................................................................. 29
Maximum Distance .............................................................................................................................. 29
TQ0301 Patch Antenna and TQ0064 RF Extension Cable........................................................................ 30
Chapter 2: Installing the Access Point ........................................................................................................ 33
Reviewing Safety Precautions ................................................................................................................... 34
Unpacking the Access Point ...................................................................................................................... 36
Attaching the Ground Cable to the Access Point....................................................................................... 39
Guidelines to Attaching the Ground Cable .......................................................................................... 39
What to Prepare for Attaching the Ground Cable................................................................................ 39
Attaching the Ground Cable to the Access Point ................................................................................ 39
Connecting an Ethernet Cable to the Access Point ................................................................................... 42
Attaching the Antennas to the Access Point .............................................................................................. 46
Installing the Access Point ......................................................................................................................... 49
Guidelines to Installing the Access Point on a Fixture......................................................................... 49
Installation Instructions ........................................................................................................................ 51
Installing the Access Point on a Wall ......................................................................................................... 52
What to Prepare for Wall Installation ................................................................................................... 52
Installing the Access Point on a Wall................................................................................................... 52
Installing the Access Point on a Pole......................................................................................................... 56
Two Methods to Install the Access Point on a Pole............................................................................. 56
Vertical Pole and Horizontal Pole ........................................................................................................ 58
Guidelines for Pole Installation ............................................................................................................ 58
Installing on a Pole Using the U-Bolts and Pole-Mount Bracket ................................................................ 59

TQ6702e GEN2 Outdoor Access Point Installation Guide
10
What to Prepare for Pole Installation Using the U-Bolts and Pole-Mount Bracket...............................59
Installing the Access Point on a Pole Using the U-Bolts and Pole-Mount Bracket ..............................59
Adjusting the Position Upwards or Downwards ...................................................................................61
Installing on a Pole Using the Pole Straps and Mounting Base .................................................................62
What to Prepare for Pole Installation Using the Pole Straps and Mounting Base................................62
Installing the Access Point on a Pole Using the Pole Straps and Mounting Base ...............................62
Starting the First Management Session on the Access Point.....................................................................67
Setting the Country and Location ...............................................................................................................69
Setting the Country ..............................................................................................................................69
Setting the Location .............................................................................................................................70
Rebooting the Access Point.................................................................................................................71
Chapter 3: Installing the TQ0301 Patch Antenna and TQ0064 Extension Cable ......................................73
Unpacking the TQ0301 Dual-band Patch Antenna ....................................................................................74
Unpacking the TQ0064 Extension Cable ...................................................................................................76
Installing the TQ0301 Patch Antenna on a Pole.........................................................................................77
Guideline for Pole Installation ..............................................................................................................77
Attaching the Cables to the TQ0301 Patch Antenna..................................................................................78
Installing the TQ0301 Antenna and TQ6702e GEN2 Access Point ...........................................................79
Attaching the Cable to the TQ6702e GEN2 Access Point ...................................................................80
Appendix A: Technical Specifications and Statements .............................................................................83
TQ6702e GEN2 Access Point Specifications.............................................................................................83
Physical Specifications.........................................................................................................................83
Environmental Specifications...............................................................................................................83
Power Specifications............................................................................................................................84
Antenna Specifications.........................................................................................................................84
TQ0301Patch Antenna Specifications........................................................................................................84
Physical Specifications.........................................................................................................................84
Environmental Specifications...............................................................................................................84
Product Specifications..........................................................................................................................85
Power Specifications............................................................................................................................85
TQ0064 and Cables in TQ6702e GEN2 Access Point Specifications........................................................85
Physical Specifications.........................................................................................................................85
Environmental Specifications...............................................................................................................86
Product Specifications..........................................................................................................................86
Power Specifications............................................................................................................................86
LAN Port .....................................................................................................................................................87
Operation Frequency Information...............................................................................................................89
IC Statements.............................................................................................................................................90
IC Radiation Exposure Statement........................................................................................................90
Déclaration d’exposition à la radiation .................................................................................................90
Caution.................................................................................................................................................90
Avertissement ......................................................................................................................................91
Professional Installation Instruction......................................................................................................91
Instructions d'installation professionnelle:............................................................................................91
Europe - EU Declaration of Conformity ......................................................................................................92
Operating Frequencies and Maximum Transmission Power Levels....................................................92
Radiation Exposure Statement ............................................................................................................92
Importer................................................................................................................................................92
UK - UKCA Declaration of Conformity........................................................................................................93
Operating Frequencies and Maximum Transmission Power Levels....................................................93
Radiation Exposure Statement ............................................................................................................93
Importer................................................................................................................................................93

11
Figure 1: Front Panel of the TQ6702e GEN2 Access Point .................................................................................................24
Figure 2: Back Panel of the TQ6702e GEN2 Access Point..................................................................................................24
Figure 3: Ethernet LAN Port .................................................................................................................................................26
Figure 4: LEDs......................................................................................................................................................................27
Figure 5: Reset Button..........................................................................................................................................................28
Figure 6: TQ0301 Dual-band Patch Antenna and 2m RF Cables ........................................................................................30
Figure 7: TQ0301 Ports ........................................................................................................................................................31
Figure 8: TQ0064 10m RF Extension Cable.........................................................................................................................31
Figure 9: Ground Posts ........................................................................................................................................................40
Figure 10: Connecting the Ground Wire to the Access Point ...............................................................................................40
Figure 11: Removing the Cap from the LAN Port.................................................................................................................42
Figure 12: Sealing Nut, Clamping Claw, and Sealing Insert.................................................................................................43
Figure 13: Sliding the Ethernet LAN Cable Through the Sealing Nut and Clamping Claw...................................................43
Figure 14: Installing the Sealing Insert .................................................................................................................................44
Figure 15: Inserting the Sealing Insert in the Clawing Clamp...............................................................................................44
Figure 16: Connecting the LAN Cable to the Ethernet LAN Port..........................................................................................45
Figure 17: Tightening the Sealing Nut ..................................................................................................................................45
Figure 18: Attaching a Surge Protector to an Antenna Connector .......................................................................................46
Figure 19: Screwing the Nut onto the Surge Protector.........................................................................................................46
Figure 20: Installing the Metal and Rubber Washers on the Surge Protector ......................................................................47
Figure 21: Installing an Antenna on a Surge Protector.........................................................................................................47
Figure 22: Tightening the Nut to Secure the Antenna ..........................................................................................................48
Figure 23: Installing the Antennas to the Access Point ........................................................................................................48
Figure 24: Orientations of the Mounting Base to the Access Point ......................................................................................49
Figure 25: Correct Orientation ..............................................................................................................................................50
Figure 26: Invalid Orientations of the Access Point..............................................................................................................51
Figure 27: Marking the Mounting Base Holes on the Wall....................................................................................................53
Figure 28: Attaching the Mounting Base to the Access Point...............................................................................................54
Figure 29: Attaching the Access Point to the Wall................................................................................................................55
Figure 30: Two Methods of Pole Installations.......................................................................................................................56
Figure 31: Pole Orientations for the Access Point................................................................................................................58
Figure 32: Attaching the Pole-Mount Bracket to the Pole.....................................................................................................60
Figure 33: Attaching the Access Point to the Pole-Mount Brackets .....................................................................................61
Figure 34: Threading the Pole Straps...................................................................................................................................63
Figure 35: Wrapping the Pole Straps Around the Pole.........................................................................................................64
Figure 36: Inserting the Strap Ends into the Screws ............................................................................................................65
Figure 37: Tightening the Straps ..........................................................................................................................................66
Figure 38: Login Window......................................................................................................................................................68
Figure 39: Basic Settings for Radio1 ....................................................................................................................................69
Figure 40: Basic Settings for Radio1 ....................................................................................................................................70
Figure 41: TQ0301 Patch Antenna on a Polr .......................................................................................................................77
Figure 42: Attaching the Cables to the Antenna Connectors................................................................................................78
Figure 43: TQ6702e GEN2 Access Point and TQ0301 Patch Antenna ...............................................................................79
Figure 44: Cables and Antenna Connectors on the TQ6702e GEN2 Access Point.............................................................80
Figure 45: Attaching the cable to an Antenna Connector.....................................................................................................81
Figure 46: Pin Layout for the RJ45 Connector on the LAN Port...........................................................................................87
Figures

TQ6702e GEN2 Outdoor Access Point Installation Guide
12

13
Table 1. Specifications of the TQ6702e GEN2 Wireless Access Points ...........................................................................22
Table 2. Components of the Access Point ..........................................................................................................................25
Table 3. LEDs .....................................................................................................................................................................28
Table 4. Components in the TQ6702e Access Point Shipping Boxes ................................................................................36
Table 5. Pole Sizes and Angles .........................................................................................................................................57
Table 6. Components in the TQ0301 Patch Antenna Shipping Boxes ...............................................................................74
Table 7. Component in the TQ0064 Extension Cable Shipping Boxes ..............................................................................76
Table 8. TQ6702e GEN2 Physical Specifications ..............................................................................................................83
Table 9. Environmental Specifications ................................................................................................................................83
Table 10. TQ6702e GEN2 Maximum Power Consumption ................................................................................................84
Table 11. Antenna Specifications .......................................................................................................................................84
Table 12. Frequency and Gain ...........................................................................................................................................84
Table 13. TQ0301 Antenna Physical Specifications ...........................................................................................................84
Table 14. TQ0301 Antenna Environmental Specifications .................................................................................................84
Table 15. TQ0301 Antenna Product Specifications ............................................................................................................85
Table 16. TQ0301 Power Input ..........................................................................................................................................85
Table 17. Cable Physical Specifiations ...............................................................................................................................85
Table 18. Cable Environmental Specifications ...................................................................................................................86
Table 19. Cable Product Specifications ..............................................................................................................................86
Table 20. Cable Power Handling ........................................................................................................................................86
Table 21. LAN Port Specifications ......................................................................................................................................87
Table 22. MDI Pin Signals (100Base-TX) ...........................................................................................................................87
Table 23. MDI-X Pin Signals (100Base-TX) .......................................................................................................................87
Table 24. 1000Base-T Connector Pinouts ..........................................................................................................................88
Table 25. Operation Frequency ..........................................................................................................................................89
Tables

TQ6702e GEN2 Outdoor Access Point Installation Guide
14

15
Preface
This guide contains the hardware installation instructions for the following
products:
TQ6702e GEN2 Outdoor Wireless Access Point
TQ0301 Dual-band Patch Antenna
TQ0064 RF Extension Cable
This preface contains the following sections:
“Safety Symbols Used in this Document” on page 16
“Professional Installation Instructions” on page 17
“Contacting Allied Telesis” on page 18

TQ6702e GEN2 Outdoor Access Point Installation Guide
16
Safety Symbols Used in this Document
This document uses the following conventions.
Note
Notes provide additional information.
Caution
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warning
Warnings inform you that performing or omitting a specific action
may result in bodily injury.

Preface
17
Professional Installation Instructions
You must comply with the following cautions:
Installation personnel
This product is designed for specific applications and needs to be
installed by a qualified individual who has RF and related rule
knowledge. The general user shall not attempt to install the product or
modify the settings.
Installation location
The product shall be installed at a location where the radiating antenna
can be kept 20cm from nearby persons in normal operation conditions
to meet regulatory RF exposure requirements.

TQ6702e GEN2 Outdoor Access Point Installation Guide
18
Contacting Allied Telesis
If you need assistance with this product, visit the Allied Telesis web site at
www.alliedtelesis.com/support.

19
Chapter 1
Product Description
This chapter describes the hardware components of the TQ6702e GEN2
access point and optional antenna and cables. This chapter contains the
following sections:
“Features of the TQ6702e GEN2 Access Point” on page 20
“TQ6000 GEN2 Models” on page 22
“Management Tools” on page 23
“TQ6702e GEN2 Access Point” on page 24
“TQ0301 Patch Antenna and TQ0064 RF Extension Cable” on page 30

TQ6702e GEN2 Outdoor Access Point Installation Guide
20
Features of the TQ6702e GEN2 Access Point
The TQ6702e GEN2 Wireless Access Point is a dual-radio access point
with 4x4 (2.4GHz) and 8x8 (5GHz) Wi-Fi 6 wireless connectivity. This
access point is suitable for both indoor and outdoor environments. With
the PoE++ LAN port, the access point can be connected to your wired
network and powered from a PoE++ power source device.
Basic hardware features include:
One 2.4GHz radio
One 5GHz radio
Four 2.4G/5GHz dual-band antennas
Four 5GHz external antennas
One 100M/1000M/2.5G/5G Base-T Ethernet LAN port
Power over Ethernet (PoE++) on the LAN port
One Reset button for restoring the default settings
LEDs for LAN, WLAN, and power
Pole or wall installation
External antenna surge protectors
N-type antenna connectors for replacing antennas
Aluminum chassis to repel ultraviolet (UV) radiation and withstand
high temperature (IP66/IP67 protection rating)
Basic features of the 2.4G and 5GHz radios include:
IEEE 802.11a/b/g/n/ac/ax
Channel blankets
Multi-channel, single channel, and hybrid operation
Automatic channel selection
Band steering
WiFi multimedia (WMM) for prioritizing traffic
Basic features of the Ethernet LAN port include:
100Mbps (IEEE 802.3u), 1000Mbps (IEEE 802.3ab), 2.5Gbps, and
5Gbps (IEEE 802.3bz)
PoE++ (IEEE 802.3bt)
Flow control (IEEE 802.3x)
VLAN tagging (IEEE 802.1Q)